Cisco Switching/Routing :: ASA 5505 Dropping Port 443 Traffic?
May 10, 2012
Networking is not my gig, but it has to be at this very moment. We have an ASA 5505. Let me explain what's going on.
On Tuesday I wanted to be able to use the ASDM since there is less room for error. But we only had a console set up. So I ran the following commands...
in ($config)
http of course didn't do anything incomplete command
http 192.168.1.2 255.255.255.255 didn't anything incomplete command
http 192.168.200.254 255.255.255.255 inside
[Code]....
Everything started working after that. Everything worked fine all of wednesday and thursday. Then this morning it stopped processing again. When I traceroute it gets to the machine that is hooked up to the console and stops. So I'm guessing its actually getting to the ASA router and being swallowed up again...
View 23 Replies
ADVERTISEMENT
Jun 5, 2013
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
View 2 Replies
View Related
Jul 21, 2012
We have a Cisco ASA 5505 (v7.2(3)) with a "fairly" normal configuration yet we have a problem where it appears UDP/53 traffic is denied on our inside network.
here is output from our sys log:
SyslogID Source IP Dest IP Description
305006 172.18.22.3 portmap translation creation failed for udp src inside:172.18.22.156/42013 dst inside:172.18.22.3/53
To give some clarification:
172.18.22.3 is one of our DNS servers
172.18.22.156 is a device we're experimenting with.
We've bypassed the Cisco by using a 4G wireless router with this same device - and it works flawlessly.Here is a [scrubbed] copy of our config. It is what I inherited from the previous admin - I'm not sure of all its finer points (I'm not Cisco certified -- perhaps I'm just certifiable.)
: Saved
:
ASA Version 7.2(3)
!
hostname [redacted]
[code].....
View 5 Replies
View Related
May 13, 2012
We have a switch that, when configuring auto qos on and edge port facing video equipment, the upstream port channel drops. I was wondering if no auto qos would have to be configured on the member ports of the port channel prior to enabling auto qos on any other ports.
View 2 Replies
View Related
Sep 24, 2012
I inherited a Cisco ASA 5505 and am trying to piggy back the device off of an established Network. Here is the basic layout:
192.168.10.1 (Core Router - Handles DHCP/DNS)
192.168.10.9 (ASA 5505 - Piggy backing off of Network)
192.168.40.x (ASA 5505 - VLAN)
I'm able to get onto the Internet without any problems. Devices from the 192.168.10x Network can not ping the inside VLAN1 (192.168.40.x). However, I would like traffic going from the inside VLAN to the Outside VLAN to be blocked, except for 192.168.10.1 and 192.168.10.9. I've tried using ACL's but end up killing my Internet connection. 192.168.10.1 is the default route and is how I get out to the Internet. Is this possible? Essentially, I'm trying to set up a small Network that guests can connect to. The idea is that they can get to the Internet, but that is it. They can't get to internal resources on the 192.168.10.x Network
Here is the config:
ASA Version 8.2(1)
!
hostname ciscoasa
enable password EeCsulrpu.9LalEE encrypted
[Code].....
View 5 Replies
View Related
Dec 12, 2011
Been dealing with a strange problem for several days now. It started out with a problem that I thought was VTP related but ended up being something else. I setup a span port on a 3750 that I am connected to that was mirroring the trunk connection coming into the switch.
Never saw an VTP traffic come across the connection but doing a sh vtp status indicated the traffic was arriving and getting processed. When I found some debug commands (debug sw-lan vtp), I was also able to see the packets go between switches. Seeing this issue concerns me that there is other traffic that isnt showing up during a span session.
I know that doing a span on a switch, especially using a trunk port as a source, isnt a good idea. Since I didnt have a TAP at time, this was my only choice. I have since borrowed a NetOptics TP-CU3 tap from a good friend and was able to confirm the VTP traffic was going across the trunk connection between switches.
All of my 3750's are running 12.2.55.SE.
View 8 Replies
View Related
Dec 12, 2011
How do I redirect my port 80 traffic to my Trend Micro IWSVA in my 3550 switch? How do I use PBR? Can I use WCCP in my 3550?
View 3 Replies
View Related
Apr 24, 2012
I am looking to find a command or counter to tell me if a cisco switch port on a 4510 was ever up and passed traffic. I want to shutdown all unused switchports on our access switches. But before I do that I need to make sure device is just not off or the person is away on vacation. If I do sh int interface, is there a counter I can reference.
View 4 Replies
View Related
Jun 18, 2012
We would like to setup a link to our DR site that is separate from our main network traffic. This link will be used by an EMC VNX SAN for replication traffic. The SAN will be plugged into a fiber port on a 3750 switch and going out from the same switch (going in as multimode, going out as single mode) into a patch panel that runs over to the DR site (about a mile away). At the DR site it will go from the fiber panel into another 3750 switch which ends up going back out of that switch into our DR SAN.
I'm wondering what the best way would be to configure the fiber ports to accomplish this. I'm affraid that the replication traffic will find it's way over through another route and congest our main network unless configured appropriately.
View 4 Replies
View Related
Nov 16, 2011
Can the SRP547W be configured to allow traffic on port 25 from an external ip range to an internal address?
View 0 Replies
View Related
Nov 27, 2012
I want to know what is the best way to black traffic inside the same VLAN, this VLAN is a user VLAN, it means that I am talking about access layer.I wanted to use private vlan, but C2960S doesn't support this feature. Any other way to prevent any to any traffic in the user vlan, this vlan only have to speak at the Layer 3.
View 2 Replies
View Related
Dec 17, 2012
How do I limit broadcast/mulitcast traffic on a switchport to e.g. 5000 pps ? I don't want the port to shut down, just block or drop broadcast traffic that exceeds 5000 pps.
View 19 Replies
View Related
Feb 6, 2013
So I took a laptop with wireshark and plugged it into a nexus 5000 port that is configured as a trunk with 3 vlans allowed on it. The laptop was seeing all kinds of traffic on the wire, most of it was not involving my laptop.
For example: Server A VLAN 10= 10.10.10.1 Server B VLAN 20= 10.20.20.1 and wireshark laptop is plugged into a trunk port which is allowing those vlan's. The vlan's are routable.
10.10.10.3 is seeing the entire conversation when 10.10.10.1 backs up 10.20.20.1 even though it has no reason to see it. It is as if the trunk is spanning traffic to the laptop port. No span is setup however. It's really weird. This is not just broadcast traffic, but actual tcp taffic between Server A and B. Why would a trunk port see traffic between 2 other servers talking to each other on the vlan.
Trunk port configuration below:
Interface Ethernet 141/1/3
switchport mode trunk
switchport trunk allowed vlan 10, 20
View 5 Replies
View Related
Nov 20, 2011
We have Cisco 3524XL switch, Motorola AXS1800 chassis. I am configuring this cisco switch so I can connect AXS1800 traffic thru cisco 3524XL, on switch port gigabit 0/1, I am using cisco Part no. WS-G5486 (1000Base-LX) connector to connect to AXS1800, both port are member of vlan 200 allowed, and configured dhcp-server 192.168.0.1, but still I can't ping any host or host can't get DHCP server.
View 2 Replies
View Related
Nov 20, 2011
Is there a way to use the "no switchport command to enable routing on a port and yet sequester it from traffic on other vlans within the switch?
The switch in question is a 3750E
View 2 Replies
View Related
Dec 26, 2011
We have Cisco 3524XL switch, Motorola AXS1800 chassis. I am configuring this Cisco switch so I can connect AXS1800 traffic thru Cisco 3524XL, on switch port gigabit 0/1, I am using Cisco Part no. WS-G5486 (1000Base-LX) connector to connect to AXS1800, both port are member of v lan 200 allowed, and configured dhcp-server 192.168.0.1, but still I can't ping any host or host can't get DHCP server. I have attached my config file for your review.
View 25 Replies
View Related
Oct 3, 2012
I am attempting to block all FTP traffic on port 21 from the servers in my network, and only allow FTP from one server to go out.
I have created the following ACL
access-list 101 Permit ip any any
access-list 101 Permit 21 1.1.1.1 0.0.0.0 any
access-list 101 Deny 21 any any
and have applied it to my truck VPN that goes up to my firewall
int Vlanxxx
ip access-group 101 out
But when i test ftp is still allowed by all servers.
View 6 Replies
View Related
May 9, 2012
I am testing out some inspection options on an ASA 5505, and I am running into a situation in which applying a http inspection is dropping all outbound http traffic. I get a "protocol violation" error in the logs.
Here is the setup: I'm not sure why the web traffic is getting dropped.
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
[Code].....
View 2 Replies
View Related
Apr 14, 2013
I have 2 Vlans with seperate networks and want to create a route between one server in vlan 465 to another server in vlan 436 via port 80.Vlan 465 has a ASA 5505 inside that IP address 89.254.12.35 will be initiating the connection to address 10.200.1.213.
-Vlan 465: server address 10.200.1.213
-Vlan 436: server address 89.254.12.35
However for extended security I would like to restrict the firewall opening to an IP to IP opening.
View 7 Replies
View Related
Aug 4, 2012
I am trying to limit the incoming and outgoing traffic on a l2 port to 8mbps for a ip subnet within the nexus 7000. The port is connected to my ISP router which has a bandwidth of 20mbps.Policing won't work on a l2 Port and shaping cannot be applied on a port level. url...I have been reading thru the qos guide for nexus release v6 and have problems understanding the different queues.
View 3 Replies
View Related
Mar 26, 2013
We have some ASR WAN routers which have a dedicated 400M interface to a remote site.
Servers on our Local network source the data through some firewalls via 10G interfaces, which connects to 4500X WAN switches then to the Routers on 1G links.
The sources are rate limiting the traffic but the routers are periodically dropping packets which I think is mostly due to burstiness in the traffic between as it traverses through from 10G links to 1G then to 400M.
How to setup traffic shaping on the 4500X outbound port to our WAN routers.I'd like to see if we could buffer and smoothe out the traffic as it exits the 4500X WAN switch 1G port to the WAN Routers.
View 1 Replies
View Related
Jun 22, 2012
I have couple C2960G and C3750. Is there any way to filter (on ingress port) type of traffic? I would like to allow IP only, and discard (i.e.) IPX, or other garbage, that any device can produce.I have tried to find something about this, but only thing I have found is feature : protocol filter, which doesn't seems to be working on my hardware.
View 6 Replies
View Related
Nov 2, 2011
Is it possible to configure the span(switch port analyzer) port and restrict it to only listen to ingress and egress of TCP/1433 from the source port?
View 2 Replies
View Related
Feb 19, 2013
I have a Cisco ASA 5505 with a fairly simple set up. Few VPN tunnels and only 3 open ports for applications. I have entered the following lines static (inside,outside) tcp interface 9002 10.0.3.230 9002 netmask 255.255.255.255 access-list outside_access_in extended permit tcp any interface outside eq 9002.I have done this before with zero issues. The other two ports are open, however, port 9002 will not be visable from the outside. The ASA says it is open, but if I go to a site like canyouseeme, it shows closed. I cannot connect to the application either.
View 3 Replies
View Related
Apr 29, 2013
I need to configure pop3 port to be open on my ASA 5505. I've created an acl and static route to do this but for some reason, it's not open.
View 1 Replies
View Related
Dec 20, 2012
In my LAN environment, I'm using two cisco SG300-10 switches. Both switches are connected by GE10 on both switches, where both ports are set to trunk.Now on all ports 1-9 on both switches, I'm having client computers attached. So I set ports 1-9 to "access" mode.All interfaces on any switch is left in default vlan.
Is it normal that I see all traffic from all connected devices on any port where I connect a listening device?What I'd like to achieve is, that only traffic that is meant for a specific workstation is actually forwarded to this workstation. By now it seems that I get all the traffic from everybody.
View 6 Replies
View Related
Jul 7, 2012
How to configure traffic flow between computers inside VLANs and a routed port? Here is the setup details:
1. Switch 3750-X
2. VLAN 100 - ( SVI IP address 192.168.100.1 /24)
3. VLAN 200 - ( SVI IP address 192.168.200.1 /24)
4. routed port gi1/0/48 (IP address 192.168.150.1 /24). Note: this port is directly connected to a firewall ASA 5520 port IP 192.168.150.100 /24
Ip routing is enabled on the switch and inter vlan traffic is flowing ok. I can ping the routed port gi1/0/48 from any computer connected in the VLAN 100 or 200. For example computer with IP 192.168.100.25 can ping the routed port 192.168.150.1. Switch can ping firewall port 192.168.150.100 and the 'sh ip route' command shows the network 192.168.150.0 /24 as directly connected network.
any computer in the two VLANs CANNOT ping firewall ASA port 192.168.150.100 Is it because inter VLAN routing does not work with a routed port on L3 switch? I looked up fallback bridging, but it is meant for non IP traffic.The goal is I am trying to set the ASA port as an internet gateway for VLANs.
View 4 Replies
View Related
Apr 25, 2011
I have setup an ASA 5505 w/ Security Plus with three subnets. The subnets are as follows:
VLANSubnetWAN 10.0.0.80/29LAN192.168.1.0/24DMZ172.30.200.0/24 ]
The ASA is the gateway router at .1 for the LAN and DMZ networks. On the WAN network, the ASA occupies .85 and uses .86 as it's gateway to the Internet. Clients on the LAN are able to access the Internet without any troubles. I have a static NAT setup to map the DMZ server's 172.30.200.81 address to 10.0.0.81. I also have a general NAT that should allow other servers on that network to access the internet, but no machine at all on that network can route outside of 172.30.200.0/24. I used the packet tracer and had it trace traffic coming from the DMZ network to the Internet, and it did not show me any conflicts with any of the access lists or anything else. However, no matter what I do, I cannot initiate traffic from the DMZ and have it go out to the Internet successfully.I attempted to follow the directions in the article PIX/ASA 7.x and above: Mail (SMTP) Server Access on the DMZ Configuration Example; but I have obviously missed something, done something wrong, or perhaps the example assumes something about my configuration that I have not done. See the attached config file that I have scrubbed. I have removed VPN configuration information and other unnecessary parts of the config file to make it easier to read. I have setup an ASA 5505 w/ Security Plus with three subnets. The subnets are as follows: VLANSubnetWAN 10.0.0.80/29LAN192.168.1.0/24DMZ172.30.200.0/24 ]
View 4 Replies
View Related
Oct 9, 2012
I want to be able to use port 1-80 for all outgoing traffic. I have a VPS outside my home, which can redirect the packets to the prober ports.Is it possible with an application on the computer and VPS? Or is it impossible?
View 1 Replies
View Related
Aug 22, 2011
I am deployting a AS 5505 unit. It is connecting a Site to Site LAN but all the traffice needs to "routed" on the "outside" network.
Example:
ASA 5505 LAN IP: 192.168.11.1
(
Tunnel: xxx.xxx.xxx.150 -> yyy.yyy.yyy.50 (Completed!)
[Code].....
View 2 Replies
View Related
Jul 18, 2011
I have a setup like this.
Foreach computer I need to go and configure the browser proxy settings and some people are getting smart and turn it to automatic configuration again.
So what i want to achieve is to have my DIR-655 to route all the HTTP/port 80 traffic to the proxy server.
That way it is transparent and then it is not needed to configure each computers browser settings.
I am pretty new to this and the router configurations.
The proxy server works fine if i configure the browser manually.
View 6 Replies
View Related
Dec 26, 2012
We have a customer who uses about 20 x c2960's switches for access layer and 2 x c3560e for distribution layer. C2960's uses C2960-LANLITEK9-M , Version 12.2(58)SE1. Everything was working fine. Now we got information, that sometimes there are problems with connectivity. Customer tries to reach internet.
SW11#sh int fa0/18
FastEthernet0/18 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is e8ba.806a.4412 (bia e8ba.806a.4412)
[Code].....
View 7 Replies
View Related
Jan 16, 2012
I have a problem where only the 2950's switches go transperant. They drop VLAN1 thus no CDP snmp packets. The users keep working fine but our NMS center keeps calling me at 3am when this happens.
These are access switches that connect to stacked 3750's. Some of the uplinks are using media converters that i have been trying to get removed. But i doubt that it could be the cause of the vlan1 going down.
View 3 Replies
View Related
