I am deployting a AS 5505 unit. It is connecting a Site to Site LAN but all the traffice needs to "routed" on the "outside" network.
Example:
ASA 5505 LAN IP: 192.168.11.1
(
Tunnel: xxx.xxx.xxx.150 -> yyy.yyy.yyy.50 (Completed!)
[Code].....
Networking is not my gig, but it has to be at this very moment. We have an ASA 5505. Let me explain what's going on.
On Tuesday I wanted to be able to use the ASDM since there is less room for error. But we only had a console set up. So I ran the following commands...
in ($config)
http of course didn't do anything incomplete command
http 192.168.1.2 255.255.255.255 didn't anything incomplete command
http 192.168.200.254 255.255.255.255 inside
[Code]....
Everything started working after that. Everything worked fine all of wednesday and thursday. Then this morning it stopped processing again. When I traceroute it gets to the machine that is hooked up to the console and stops. So I'm guessing its actually getting to the ASA router and being swallowed up again...
I have 2 Vlans with seperate networks and want to create a route between one server in vlan 465 to another server in vlan 436 via port 80.Vlan 465 has a ASA 5505 inside that IP address 89.254.12.35 will be initiating the connection to address 10.200.1.213.
-Vlan 465: server address 10.200.1.213
-Vlan 436: server address 89.254.12.35
However for extended security I would like to restrict the firewall opening to an IP to IP opening.
I have a Cisco ASA 5505 with a fairly simple set up. Few VPN tunnels and only 3 open ports for applications. I have entered the following lines static (inside,outside) tcp interface 9002 10.0.3.230 9002 netmask 255.255.255.255 access-list outside_access_in extended permit tcp any interface outside eq 9002.I have done this before with zero issues. The other two ports are open, however, port 9002 will not be visable from the outside. The ASA says it is open, but if I go to a site like canyouseeme, it shows closed. I cannot connect to the application either.
View 3 Replies View RelatedI need to configure pop3 port to be open on my ASA 5505. I've created an acl and static route to do this but for some reason, it's not open.
View 1 Replies View RelatedI am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.
View 12 Replies View RelatedSo here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
With the Cisco ASA-5505, is there a more secure port that can be configured for VNC other than 5901? I am new to Firewalls We have a User who has requested that 5901 be opened but I was advised not to do so for security concerns.
View 5 Replies View RelatedI have the following configuration in my ASA 5505 and I'm having problems connecting with other players on my XBox.
I think my problem is that I need to forward ports tcp:3074, udp:3074, and udp:88 to my xbox which is at 192.168.2.50 (vlan 3 below).
Trying to do port forwarding so that one particular host located on the WAN can get access to a LAN box on a specific port via the public IP.
Here's what I've setup on the ASA (IP addresses and port number have been changed to protect the innocent):
I would like to be able to do SSH port forwarding from outside to an IP address inside. Normally, this is very straighforward.
The problem now is that if I do so, then the LAN to LAN VPN stops working!.There is a LAN to LAN VPN working flawlesly (so far) between an ASA 5505 and a Cisco 861 Integrated Router. However, I would like also, to give SSH access to an IP address behind the Cisco router. The moment I do this the VPN breaks!
I attached the Cisco 861 router configuration, where the problem shows. The ASA has public IP X.X.X.105 and the router has X.X.X.105. These two are used for the VPN tunnel.
The internal network in the ASA is 10.115.16.0/24 and 192.168.10.0/24 in the router. These talk to each other using the tunnelt. But, the moment I try to forward port 22 in the router from X.X.X.107 to 192.168.10.30 the VPN breaks! I do that with the following line: ip nat inside source static tcp 192.168.10.30 22 X.X.X.107 22.Obviously, something is eluding me. The configuration is rather short and simple. But, I'm a newbie with Cisco rotuer configuration. Note that the tunnel stays up after I use the natting entry and I can talk from the router to the ASA, but not the other way around!The router is Cisco 861 with IOS version 15.0(1)M7.
We have an ASA 5505 and I need to set up port forwarding for an unusual port number which will be used for FTP on an IIS server.It's a bit complex as there are 3 VLANs: these are called ISP, Server and LAN-side VPN. We need to add a TCP port 8521 forward from the server's IP in Server WAN to ISP WAN VLAN with public IP address.
View 1 Replies View RelatedI am working on an ASA5505 and am trying to open the ftp port. I have a server (192.168.10.202) on the local LAN which is attempting to download antivirus updates from the net via ftp.
Saved
:
ASA Version 8.3(2)
!
hostname SITE
enable password XXXXXX
passwd XXXXXX
names
[code]....
how do you enabled multiple port mapping on asa 5505? i want to use 1 static ip address for rdp connection for 15 users, and the port will start from 3390 to 3340.
View 4 Replies View RelatedI need to open ports 9080 and 5280 on my Cisco ASA 5505 firewall and despite doing everything I THINK I needed to do...when I run the utility to check from outside; it is NOT open....I utilize a website called [URL] (very good for these kinds of things) I have added the specific port(s) to my services so that I can CHOOSE them; added an ACE/ACL to; added incoming/outgoing rules to accomodate traffic to those ports....NOTHING.
View 7 Replies View RelatedWe are trying to install filter software at our main location and branches. The admin console has been installed at the main branch, but I need to allow access to ports 58000-58003 through our firewall in order to successfully install the software at our branches.
View 1 Replies View Relatedhave a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.All this box really does is port forward external clients to 1 address on the internal lan for client software updates.So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
View 16 Replies View RelatedI have ASA5505 and am having issue with port forwarding NAT . [code]
View 11 Replies View Relatedmy friend was against a wall trying to update her office's system, and it seems like every Cisco person in the region has gone on vacation.For some sort of new system her office is getting, she was told that she needed to enable NAT with external IP xxx.xxx.xxx.14 (The ASA's IP is xxx.xxx.xxx.11) and internal IP xxx.xxx.xxx.58 and that port 8222 needs to be open. I know this is sort of vague, but it's what she was given, and I know the 8222 port is very specific in function,?
At any rate, the best I could come up with was to run:
static (inside,outside) xxx.xxx.xxx.58 xxx.xxx.xxx.14 netmask 255.255.255.255
access-list inbound extended permit tcp any host xxx.xxx.xxx.11 eq www
access-list inbound extended permit tcp any host xxx.xxx.xxx.11 eq https
access-list inbound extended permit tcp any host xxx.xxx.xxx.11 eq 8222
access-list inbound extended permit udp any host xxx.xxx.xxx.11 eq 8222
access-group inbound in interface outside
But after I inserted this, she did what she was supposed to be able to do (went home and tried to run some sort of remote installation file) and it didn't work...
I have an ASA 5505 running 8.4.I am only letting ICMP traffic in from the outside.As a test, I opened a couple of ports I need on the ASA.I cannot access these ports and I do not get a denied error in the log.
I contacted the ISP and they are not blocking these ports.I ran an online port scanner to check ports 1-100 as a test. They all came up as blocked on the port scanner. The only deny error I got on the ASA was for port 80.Is this normal behavior? If so, how do I get it to show all of the deny errors so I know the traffic is at least hitting the firewall?
I have the following configuration in my ASA 5505 and I'm having problems connecting with other players on my XBox (moderate NAT).
I think my problem is that I need to forward ports tcp:3074, udp:3074, and udp:88 to my xbox which is at 192.168.2.50 (vlan 3 below).
[code]
# sh run
: Saved
:
[Code].....
I am trying to forward specific ports from the outside interface on my ASA5505 to my servers inside and can not get it to work! I have a VPN that currently works and the firewall rule in place I am just overlooking something simple I'm sure. Here is the config:
ASA Version 8.2(5)
!
hostname ASA
enable password <removed>
passwd <removed>
[Code]...
I have been asked to "forward a port on an ASA 5505 to an internal ip address." Sounds easy for most of you, and I thought I did it right, but I am not certain. Basically, they want it set up so that when xx.xx.xx.xx:30000 (x's = the firewall ip with port 30000) is accessed from outside, it is forwarded to an internal ip on port 30000 (xxx.xxx.x.xxx:30000)
Here is what I tried from within ASDM 6.4:
1. NAT Rules-add static NAT route:
original-Interface: inside
-Source: xx.xx.xx.xx (local ip of computer on LAN they wish to access from outside)
Translated - Interface - Use Interface IP Address
Enable PAT: Original and Translated port both set to 30000
2. Access Rule - add
Interface: Inside
Source: any
Destination: xx.xx.xx.xx (IP of Firewall)
Service: tcp/30000
We are trying to setup our ASA 5505 to do port forwarding to multiple internal servers and have run into some issues. A little background on what we are trying to do.
We have 1 static external IP. Internally we have one exsisting server (10.1.1.184) that has port 80 forwarded to it and another exsisting server (10.1.1.185) that has port 443 forwarded to it. Both of these servers are serving seperate web apps to our employees who of course use them offsite. We have now added an additional server (10.1.1.186) that needs to use both ports 80 and 443. Is there any way to set it up so that these ports can be forwarded to all the servers that need them? Also, how would this work as far knowing what traffic will need to go to which server even though it is using the same port?
The equipment is: ASA 5505ASA Version 7.2(4)ASDM Version 5.2(4) I appologize in advance if what I'm trying to do is difficult/impossible. I inherted the ASA 5505 at this location and I was not here when it was initially installed. In fact no one on staff was here when it was initially installed. I did manage to find the passwords to it though. I'm not at all familiar with the ASA 5505 or Cisco secuirty appliances in general.
I want to have my port 4 on the asa 5505 only allow access to the internet and not the internal network, what do i need to do?
View 1 Replies View RelatedI've configured port forwarding on an ASA 5505 to connect to an Access Point web administration.This Is for testing purposes only. I've followed the guidelines for port forwarding and I've created an access list but I can't connect to the AP.I know It's working because It connects fine when connected to my speedtouch router.I've attached a running-config.I'm getting hit counts on the ACL and I'm getting untranslate_hits on the nat but no translate hits.
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
!
[code]......
How do I monitor connections to the DMZ port on our ASA 5505 (via ASDM 5.2)? We have a WAP connected to it and it's intermittently dropping connections.
View 2 Replies View RelatedDo I create an SMTP Network Object and send TCP traffic throught NAT?
Or do I go to the ASDM's Configuration/Firewall, choose Public Servers, and choose Private Interface=inside, Public Interface=outside, set the private/public IPs, and choose SMTP as the service? This seems much simpler, but is it the correct way to do it?
I am using ASDM 6.4(5) and would like to use that versus the CLI.
I would like to setup an cisco ASA 5505 to only allow certain IP's on port 3389, but i can't get it to work. Maybe some of you experts know why?
Here is my config:
ASA Version 8.4(3)!hostname cisco-asaenable password ** encryptedpasswd ** encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.253 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 95.*.*.* 255.255.255.248!ftp mode passiveobject network obj_anysubnet 0.0.0.0 0.0.0.0object network rdpuser-1host 46.*.*.*object network rdpuser-2host 48.*.*.*object network rdp-host-pchost 192.168.1.20object
[code].....
The allowed IP's are setup on user level (rdpuser-1 and rdpuser-2) .Still do, I can't connect to the server from any of these IP's...
We have a new installation of a ASA 5505 and are trying to get some NAT issues straightened out. On our internal network, we have two servers running Filemaker Server, a relational database server that clients connect with using port 5003. Our goal is to be able to allow users from the outside to access either of these servers as needed. I know how to set up a simple static NAT rule and matching Access rule in ASDM which would be fine for a case in which only one server using a given port is running on a network, but for simple static rules I seem to be blocked from entering a different translated port number from the orginal port number, which becomes a problem when two servers we need to access from the outside are running software using the same port number.
What is the simplest way to address this need? I am guessing that I need to set up a scenario like this, where port 5004 (or any arbitrarily choosen unused port, can be used to access the second server: [code]
I am trying to open port 52199 on my ASA 5505 I have gone to firewall, access rules and then add tcpip.Not sure if that is the correct place but cannot get it to work?
View 1 Replies View RelatedI have a customer thats got a Linksys router now, that has a DMZ port.The DMZ port is configurede to it routes the extra public ip-adress to the DMZ port it has.At the DMZ port they have another router connected, where they routes the public ip-adresses på some other devices.How can i make this setup on a Cisco ASA 5505 (With the Security Plus licens)What i have to do is to replace the Linksys router, and make it so, so it works like it was before with the Linksys.
View 5 Replies View RelatedI have ASA 5505 with 8.4(2)8 software for one of my branch offices and I can't configure port forwarding.It seems to be very simple, but it's not working. I use my ASA as a gateway to the internet for users in office and for site-to-site IPSec VPN to HQ. I have pppoe-enabled outside interface, but ISP gives me static routable ip address. I have server behind my firewall and I should "publish" to the WAN some of its' tcp and udp ports, but I see that no packets forwarded through ASA. I tried to configure PAT as stated in official "Cisco Security Appliance Configuration Guide" through CLI and ASDM.[code]
View 4 Replies View Related