Cisco Firewall :: ASA 5505 Port Blocking?
Jun 24, 2012
I have an ASA 5505 running 8.4.I am only letting ICMP traffic in from the outside.As a test, I opened a couple of ports I need on the ASA.I cannot access these ports and I do not get a denied error in the log.
I contacted the ISP and they are not blocking these ports.I ran an online port scanner to check ports 1-100 as a test. They all came up as blocked on the port scanner. The only deny error I got on the ASA was for port 80.Is this normal behavior? If so, how do I get it to show all of the deny errors so I know the traffic is at least hitting the firewall?
View 2 Replies
ADVERTISEMENT
Nov 28, 2011
I am working on an ASA5505 and am trying to open the ftp port. I have a server (192.168.10.202) on the local LAN which is attempting to download antivirus updates from the net via ftp.
Saved
:
ASA Version 8.3(2)
!
hostname SITE
enable password XXXXXX
passwd XXXXXX
names
[code]....
View 4 Replies
View Related
Sep 8, 2011
I am required to block the IP neworks used by approx 10 coutries. The issue is if using an ACL this works out to be about 18,000 lines, I have done all the summarization possible.. are there any other options? as the ASA 5505 crashes when implementing this many lines.
View 3 Replies
View Related
Jan 7, 2012
Previous attempts to set up these NAT rules has been met with minimal success. We have been able to get the NAT rules created, and able to ping our inside servers and receivers from a different outside network, but every time we get that far our internal network crashes. Running the Packet Trace utility via the ASDM shows that internal traffic from the servers to the workstations is being blocked by the default implicit rule under the access rule heading that states "any to any, service being ip, action= deny". Reverse traffic from the workstations to the servers is being allowed though. In an effort to start over again, the Cisco ASA has been Factory Defaulted via the CLI, and has had it's Inside network, and Outside IP address set back up. DHCP pool has been setup for a minimal amount of addresses on the inside network, since most of our equipment will always be assigned statics. We reset our static NAT policies, and seem to be having the same problem. My partner and I have been working on this for some time now, and have ourselves so frustrated that I know we are missing something simple. [code]
View 10 Replies
View Related
Dec 13, 2010
I have a Cisco ASA 5510. I have detected an infected workstation on my internal LAN which has caused my IP to be blacklisted by Barracuda Networks and other RBL. I have scanned and cleaned the workstation removing the spambot. I want to prevent all my internal workstations from sending SMTP traffic on Port 25 through my ASA 5510 device. I only need to allow my Exchange Server access to send out traffic on port 25. configure this setup using ASDM 5.0? I know it may be easier using CLI, but using the ASDM would really be preferred.
View 4 Replies
View Related
Jul 23, 2011
I picked up a rather nasty bit of malware which resulted in a format and installation of Windows Ultimate 64, all well now except i cant get the wireless to work, downloaded assorted drivers from the dell support directory but to no avail, so questions are-:am i missing something obvious (windows function button for wireless does nothing)what is the correct driver for the N5040 and are there any tricks in getting it to work.
View 1 Replies
View Related
Oct 31, 2012
I thought I had the configuration to allow bi-directional traffic for my Blackberry server. I have a second fw with the same config and it worked on that one. But right now, my blackberry server is down, and all the users are upset.
ASA Version 8.2(2)
!
hostname asa5505
[Code]......
View 4 Replies
View Related
Dec 20, 2012
i am using asa5540 with 7.0(8). firewall was configured in transparent mode.
now i am looking for block ip phone communication from site to site and head office. i am using cucm 7.1.2b.
all site was connected through ofc. no nat was using.
View 1 Replies
View Related
Nov 26, 2012
I am attempting to block outbound traffic for a specific PC on my LAN using the ASDM.
View 2 Replies
View Related
Aug 15, 2012
I am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.
View 12 Replies
View Related
Dec 2, 2011
So here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
View 28 Replies
View Related
Aug 18, 2011
With the Cisco ASA-5505, is there a more secure port that can be configured for VNC other than 5901? I am new to Firewalls We have a User who has requested that 5901 be opened but I was advised not to do so for security concerns.
View 5 Replies
View Related
Apr 30, 2012
I have an issue with my firewall,each time i configured a trunk port in the firewall and connect a sw 2960S with a trunk port also, all the interfaces in the Firewall go down ( virutal intertaces, inside, outside , dmz) , also another switch 3750 that is connected to another port in the firewall( access port only) it start to a new negotiation of spanning tree.What could be causing this problem? the firewall didnt sedn bdpdu i think the IOS of the firewall its a 8.2
View 3 Replies
View Related
Jun 6, 2011
how do you enabled multiple port mapping on asa 5505? i want to use 1 static ip address for rdp connection for 15 users, and the port will start from 3390 to 3340.
View 4 Replies
View Related
Feb 25, 2013
have a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.All this box really does is port forward external clients to 1 address on the internal lan for client software updates.So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
View 16 Replies
View Related
Dec 6, 2012
I have ASA5505 and am having issue with port forwarding NAT . [code]
View 11 Replies
View Related
Apr 5, 2012
my friend was against a wall trying to update her office's system, and it seems like every Cisco person in the region has gone on vacation.For some sort of new system her office is getting, she was told that she needed to enable NAT with external IP xxx.xxx.xxx.14 (The ASA's IP is xxx.xxx.xxx.11) and internal IP xxx.xxx.xxx.58 and that port 8222 needs to be open. I know this is sort of vague, but it's what she was given, and I know the 8222 port is very specific in function,?
At any rate, the best I could come up with was to run:
static (inside,outside) xxx.xxx.xxx.58 xxx.xxx.xxx.14 netmask 255.255.255.255
access-list inbound extended permit tcp any host xxx.xxx.xxx.11 eq www
access-list inbound extended permit tcp any host xxx.xxx.xxx.11 eq https
access-list inbound extended permit tcp any host xxx.xxx.xxx.11 eq 8222
access-list inbound extended permit udp any host xxx.xxx.xxx.11 eq 8222
access-group inbound in interface outside
But after I inserted this, she did what she was supposed to be able to do (went home and tried to run some sort of remote installation file) and it didn't work...
View 8 Replies
View Related
Sep 1, 2012
I have the following configuration in my ASA 5505 and I'm having problems connecting with other players on my XBox (moderate NAT).
I think my problem is that I need to forward ports tcp:3074, udp:3074, and udp:88 to my xbox which is at 192.168.2.50 (vlan 3 below).
[code]
# sh run
: Saved
:
[Code].....
View 3 Replies
View Related
Oct 1, 2012
I am trying to forward specific ports from the outside interface on my ASA5505 to my servers inside and can not get it to work! I have a VPN that currently works and the firewall rule in place I am just overlooking something simple I'm sure. Here is the config:
ASA Version 8.2(5)
!
hostname ASA
enable password <removed>
passwd <removed>
[Code]...
View 16 Replies
View Related
Mar 15, 2012
We are trying to setup our ASA 5505 to do port forwarding to multiple internal servers and have run into some issues. A little background on what we are trying to do.
We have 1 static external IP. Internally we have one exsisting server (10.1.1.184) that has port 80 forwarded to it and another exsisting server (10.1.1.185) that has port 443 forwarded to it. Both of these servers are serving seperate web apps to our employees who of course use them offsite. We have now added an additional server (10.1.1.186) that needs to use both ports 80 and 443. Is there any way to set it up so that these ports can be forwarded to all the servers that need them? Also, how would this work as far knowing what traffic will need to go to which server even though it is using the same port?
The equipment is: ASA 5505ASA Version 7.2(4)ASDM Version 5.2(4) I appologize in advance if what I'm trying to do is difficult/impossible. I inherted the ASA 5505 at this location and I was not here when it was initially installed. In fact no one on staff was here when it was initially installed. I did manage to find the passwords to it though. I'm not at all familiar with the ASA 5505 or Cisco secuirty appliances in general.
View 19 Replies
View Related
Nov 20, 2011
I want to have my port 4 on the asa 5505 only allow access to the internet and not the internal network, what do i need to do?
View 1 Replies
View Related
Mar 22, 2012
How do I monitor connections to the DMZ port on our ASA 5505 (via ASDM 5.2)? We have a WAP connected to it and it's intermittently dropping connections.
View 2 Replies
View Related
May 6, 2012
I would like to setup an cisco ASA 5505 to only allow certain IP's on port 3389, but i can't get it to work. Maybe some of you experts know why?
Here is my config:
ASA Version 8.4(3)!hostname cisco-asaenable password ** encryptedpasswd ** encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.253 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 95.*.*.* 255.255.255.248!ftp mode passiveobject network obj_anysubnet 0.0.0.0 0.0.0.0object network rdpuser-1host 46.*.*.*object network rdpuser-2host 48.*.*.*object network rdp-host-pchost 192.168.1.20object
[code].....
The allowed IP's are setup on user level (rdpuser-1 and rdpuser-2) .Still do, I can't connect to the server from any of these IP's...
View 6 Replies
View Related
Apr 10, 2012
We have a new installation of a ASA 5505 and are trying to get some NAT issues straightened out. On our internal network, we have two servers running Filemaker Server, a relational database server that clients connect with using port 5003. Our goal is to be able to allow users from the outside to access either of these servers as needed. I know how to set up a simple static NAT rule and matching Access rule in ASDM which would be fine for a case in which only one server using a given port is running on a network, but for simple static rules I seem to be blocked from entering a different translated port number from the orginal port number, which becomes a problem when two servers we need to access from the outside are running software using the same port number.
What is the simplest way to address this need? I am guessing that I need to set up a scenario like this, where port 5004 (or any arbitrarily choosen unused port, can be used to access the second server: [code]
View 1 Replies
View Related
Mar 11, 2011
I am trying to open port 52199 on my ASA 5505 I have gone to firewall, access rules and then add tcpip.Not sure if that is the correct place but cannot get it to work?
View 1 Replies
View Related
May 20, 2012
I have ASA 5505 with 8.4(2)8 software for one of my branch offices and I can't configure port forwarding.It seems to be very simple, but it's not working. I use my ASA as a gateway to the internet for users in office and for site-to-site IPSec VPN to HQ. I have pppoe-enabled outside interface, but ISP gives me static routable ip address. I have server behind my firewall and I should "publish" to the WAN some of its' tcp and udp ports, but I see that no packets forwarded through ASA. I tried to configure PAT as stated in official "Cisco Security Appliance Configuration Guide" through CLI and ASDM.[code]
View 4 Replies
View Related
Dec 27, 2011
I have Cisco ASA 5505 Firewall with security plus license, Currently I open ports on 25,80,443 on public IP address 1.1.1.1 and perform static nat between the inside and outside IP address Such as i configured via CLI
access-list OUT_IN extended permit tcp any host 1.1.1.1 eq 80
access-list OUT_IN extended permit tcp any host 1.1.1.1 eq 443
access-list OUT_IN extended permit tcp any host 1.1.1.1 eq 25
[Code]......
View 1 Replies
View Related
Jan 16, 2012
when I want to let email to come through the ASA5505 from outside to DMZ and Inside network, are the below command lines correct and good enough?
access-list outside_DMZ extended permit tcp outside-network-ip dmz-network-ip eq imap4
access-list outside_DMZ extended permit tcp outside-network-ip dmz-network-ip eq pop3
access-list outside_DMZ extended permit tcp outside-network-ip dmz-network-ip eq smtp
access-list outside_inside extended permit tcp outside-network-ip inside-network-ip eq imap4
access-list outside_inside extended permit tcp outside-network-ip inside-network-ip eq pop3
[code]....
Are there any other TCP ports want to be allowed and other command lines need to be added?
View 5 Replies
View Related
May 16, 2013
We have a singe IP Address in the Internet and want to forward SMTP traffic that hits our ASA Outside Interace to the internal Mailserver.And we like to forward Http Traffic to our Webserver.
Example.
212.23.23.23 Port 25 -> 192.168.1.100 Port 25
212.23.23.23 Port 80 -> 192 168.1.200 Port 80
How do i acomplish that. Which NAT rules do in need?
View 12 Replies
View Related
May 12, 2011
how to set up port forwarding for inbound SSH?
The outside interface on the ASA is on DHCP. I have a single dynamic public IP from my ISP. The inside interface provides Internet access for the network using NAT.
I have a server on the internal network with an IP of 192.168.0.6 and I would like to access this via SSH (TCP port 22) from outside.
I've been able to do this in the past on a PIX with a static public IP block, but I'm new to ASA and I don't know how to do it with PAT.
Current running config attached for what it's worth, but it's pretty basic at the moment.
View 3 Replies
View Related
Feb 7, 2013
: Saved
: Written by enable_15 at 03:51:29.049 UTC Mon Feb 4 2013
ASA Version 8.4(4)1
host name cisco asa
enable password xxxxx encrypted
password xxxxx encrypted
names
interface Ethernet0/0
switch port access v lan 100
interface Ethernet0/1
interface Ethernet0/2
[code]...
View 2 Replies
View Related
Dec 16, 2012
Doing a port forward for remote desktop with asa 5505 9.1.1 and asdm 7.1.1 I could have done this with the previous versions of asdm but now it even more confusing?
View 21 Replies
View Related
May 26, 2012
We have 2 TS (Terminal Servers) and have configured the 1st RDP using my public address (say 8.8.8.8) on port 3389. it is working very well of course. However I need setup my 2nd TS but will use port 7777 on the same public address which is not working.I am using ASDM 6.3 and firmware 8.3.1.Is this a limitation for this IOS?
View 6 Replies
View Related
