Cisco Switching/Routing :: 7201 Connecting To Router Through Modem And AUX Port But Can't Type
Mar 29, 2010
I am having an issue with connecting to a Cisco 7201 via the AUX port through a modem. The modem is plugged into the AUX port and I am dialing into the modem, everything seems to be working fine as I get a login prompt and my banner etc but I can't type anytihng. If I type then nothings happens... If I just type a bunch of random characters on the keyboard then when the authentication prompt times out and it goes back to the username, it will show a few of those characters.. I have tried many things, changing speeds etc, I have even tried changing modems and it is doing the exact same thing.Here is my config:
line aux 0 exec-timeout 2 0 modem Dialin transport input all stopbits 1 speed 115200 flowcontrol hardware
I have searched on here and found people having similar problems but no solutions. I have tried this one a Cisco 2821 with the same config and it works with no problem, the only difference is the phone line is different.
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
I have couple C2960G and C3750. Is there any way to filter (on ingress port) type of traffic? I would like to allow IP only, and discard (i.e.) IPX, or other garbage, that any device can produce.I have tried to find something about this, but only thing I have found is feature : protocol filter, which doesn't seems to be working on my hardware.
We are planning to implement the following policy map for egress traffic on an Nexus 7000:
policy-map type queuing dd-1p3q1t-8e-out-10G class type queuing 1p3q1t-8e-out-pq1 priority level 1 shape percent 10 class type queuing 1p3q1t-8e-out-q2 bandwidth remaining percent 5 class type queuing 1p3q1t-8e-out-q3 bandwidth remaining percent 5 class type queuing 1p3q1t-8e-out-q-default bandwidth remaining percent 90
We are using two N7K's to which is one N5K connected through a vPC. From the N5k we use a port-channel with 4 * 10G. Two of this four ports are connected to on N7K and the other two are connected to the other N7K. On the n/K's we are using vPC.
My question now are:
1. Where i have to connect the policy map? To the port-channel or on each physical interface?
2. When i have to connect this policy to the port-channel, how does i have to set the shape percent, when i would like to reserve 10% from the 40G? Does i have to set the shape value to 5% on each N7K because vPC?
I am new to Cisco Nexus 7000 Series NX-OS System of appliances. I am looking for type of log events that are getting generated by CISCO Nexus 7000 switches. Some documents which give me this references & some documents which have a log line explained.
I have a 892 router configured on fa0 with vlan1 and a catalist 3560. On catalist all ports are in access mode and vlan1. When I'm connecting port fa0 from router to catalist, the catalist port is shuted down What should I do on router on catalist to make the connection working ?
I have a WS-X6816-10G-2T module with X2-10GB-SR modules. I will be getting a SMF hand off and the length of the termination is around 100 meters. (I will be getting another hand off for Inter-DC link for which I have X2-10GB-LR module). The question is can I connect this SMF hand off (short length) on the SR module?
I am planning on deploying a 2960 switch and will need to uplink it to a 4510 switch. There are 2 TenGig Ports available and I was thinking of uplinking one of them to the 1Gb SFP port on the 2960. Would this work?
In one location we have a HP 2510-48 port switch which we need to connect to a Cisco 3560 switch. The problem I have is that we have issues connecting fibre to the HP switch, so I have decided to attached a CAT 5 to Fibre convertor at this end and another to the cisco switch.
My question you can not connect a HP switch to a Cisco switch, is this true or do I just need to confirgure something on the ports.
Region : Italy Model : TL-MR3220 Hardware Version : V1 Firmware Version : 120822 ISP : TIM
I have a compatibility problem with the 3G USB Modem ONDA MT191UP with 3220 V2 updated with the firmware 120822 uploaded on TPLINK web site . Every thing is ok , the wireless is created , but the internet connection is missing . The router does not show the USB led , and it remain always in "connecting" but nothing happen . Do you have some infor to be compatible this USB modem ( some firmware , some Bin file etc..) ?I checked the Huawei E1800 and it works perfectly.
I'm new to networking and was looking for some assistance. First off im using packet tracer to diagram my senario as I will be receiving my equipment next week to deploy.
Hardware to be used:
1. 2 catalyst 3560 switches 2. all connect to a sonic wall router
I have two companies that work in the same office space. I need to keep these companies seperate on their own vlan. They will however need to share the phone system.(Packet tracer file uploaded to give those who have the time to see what I put together.) [code]
So currently I'm having issues with changing my nat type to open for my ps3. I've tried to use DMZ and port forwarding to change the nat type, but sadly I couldn't get this to work. Most the guides on the forums are for xbox's which wouldn't work for a ps3. Any handy guide to change my nat type to open for my ps3?
I'm trying to forward ports for game connections. For this particular game, I'm trying to forward port 7777My ports aren't forwarding according to: Open Port Check Tool - Test Port Forwarding on Your Router and Open Port Check Tool[CODE]
I am looking at running MPLS from from one datacentre to the other (we have a layer2 interconnect and can run jumbo frames) I need about 70 access ports (each in a seperate VRF) at the new datacentre
I am looking at :
2x 6503'-Es with sup720-3B and a 48x port linecard or 2x 7201 router with 2x 2960-S layer 2 access switches.
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
port forwarding this im trying to setup a minecraft server with bukkit and i tried a number of things to port forward and it won't open port. I have a tomato firmware linksys router and a qwest modem.
I've been testing some QoS policies, and I have not been able to make a type QoS policy work in the outbound direction. Simple example:
ip access-list QOS-VOICE 10 permit ip any 10.120.11.0/24 20 permit ip 10.120.11.0/24 any class-map type qos match-any IN-VOICE description Voice/VoIP/IPT
[code]....
The 7Ks are running NX-OS 5.2(4). Just wondering - has any one got an outbound qos policy to work on a N7K?
find out which types of fiber optic that i can connect to three types of switches. the setup that i have that there are:8 access switches (WS-C2960S-24TS-S), in each one there is two SFP connections.2 aggregate switches WS-C3750X-24T-S, in each one there is four SFP connections.and one core switches that has SFP card WS-X4624-SFP-E? Note that the fiber optic that we have coming from filed are multimode.
We've got a doubt about the uplink ports of this supervisor. I've read that you have to use the four ports in 10G mode or in 1G mode, but not use for example 1 port in 10G mode and 1 port in 1G mode:
But, you can read in another sentence: " Beginning with Cisco IOS Release 12.2(25)SG, you could simultaneously deploy the dual 10-Gigabit.Ethernet ports and the four Gigabit Ethernet SFP ports on the Catalyst 4503, Catalyst 4506, and Catalyst 4507R chassis." Is it posible deploy simultaneously both type of ports?
I try to connect a Router as an Endpoint (Because I just want to use a SERVICE from it).Well, the issue is this: I have a SW L3 that have too much VLANS, It is routing traffic and it provides internet connection. VLAN 182 has been created at this point and in this SW L3 has configured an interface vlan 182 with an IP 10.0.82.1/28.
To this Switch L3 is connected another switch L2 with an interface vlan 182 with an IP 10.0.82.2/28. Finally I have the last switch with the same features of configuration just that this has an IP 10.0.82.3/28. In this last switch is connected the router in the Gi1/0/24 as Switch port access, this port belongs to VLAN 182. At the router, the port is gi0/0 and it has an IP 10.0.82.4/28 and is UP.
The Switch where the router is connected is reachable from this router but not by the other switches. Router can reach all the network but not in the reverse way.Router has configured an ip default gateway 10.0.82.1.
I have a Cisco 2811 Router with a NM-16ESW card installed. I've connected this to my DSL connecting and I'm trying to build myself a learning lab. From the router I can ping to the internet and back to a test computer I have connected to one of the card's ethernet ports. From the test computer, I can ping the router's WAN interface, but no further. [code]
I have a cable modem with my 2600 Router and i have a little speed problem when I'm going out to the web via my F0/0.. according to regular speed test sites my speed is around 20mbps but when i hook up to my modem directly i get a solid 40mbps.. now I've changed my Cat 6 cable from my modem to my router and this are my settings in the router.
[Code] ...........
I see some drops and lost carriers but not sure what those might mean?
I have two Catalyst 2960 Series (48 port) switches with the newest Cisco IOS installed. There is also a Cisco 2600 Series Router which I can't manage because it's ISP managed.
Now the problem is as follows. I'd like to create two VLANs, one in the IP range 192.168.0.xxx and the other in the 192.168.1.xxx. Now the router has a gateway IP address 192.168.1.1 .
Would it be possible to somehow connect these two VLANs with the router so that these 2 VLANs can't see each other but they can ofcourse both contact the router and exit on the internet?
We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
I've done some tests and it seems that a 7201 supports GETVPN without a VAM, but in the design guide it states that this is needed.Is this needed as the 7201 documentation states that it performs IPSEC encryption in hardware without a VAM.
Two days ago we received our new phone land line from Mediacom. We already had internet service from them so we decided to get a phone line. When they came over two days ago, we received a new modem, RCA DHG535-2. The issue we are experiencing is that the modem is not connecting to our rt n-16 ASUS wireless router. The modem works fine without the router but we need it for school work. The troubleshooter says "DNS is not available".A few things i tried was to unplug everything and reconnect them back from the modem to the computer.It usually works when i had trouble in the past but it seems nothing is working.
I'm using a stock FIOS router Actiontec MI424WR, and I'm trying to access the router settings at 192.168.1.1. I type in my username fine, but when I type the password, each keystroke gives me more than one digit. Even holding Ctrl adds one, and letting go removes three characters. I've never seen this happen before, and I've tried it on two computers and three different browsers. I see that people recommend hard-resetting the router, but I was wondering why this has happened
config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]
I am with Virgin media and have a home lab (2611 routers, 3550 switches, 2950s etc) which i usually just use for testing things on and practicing.
Now I tried to connect it to the internet and got some weird things happening.
I got NAT and DHCP client all setup correctly on the router (or so I think!) along with DNS settings but I still can't get Internet access.
My network is all setup right so that through using OSPF the router is the gateway (0.0.0.0 route) for all devices. Doing a traceroute confirms this.
Yet I never get any further than the router? I see IP nat translations ticking up as I send more requests but never get a webpage or a reply from any of the machines in my network.
HOWEVER... The router itself does get some replies from Google.co.uk and bbc.co.uk but doesn't seem to want to give anything else on the "inside" a response?
Here is a dump of config:
version 12.4 service timestamps debug datetime msec service timestamps log datetime msec
