Cisco Switching/Routing :: WS-C2960S-24TS-S / What Type Of Fiber Optic Can Be Connected To New Switches
Jan 16, 2012
find out which types of fiber optic that i can connect to three types of switches. the setup that i have that there are:8 access switches (WS-C2960S-24TS-S), in each one there is two SFP connections.2 aggregate switches WS-C3750X-24T-S, in each one there is four SFP connections.and one core switches that has SFP card WS-X4624-SFP-E? Note that the fiber optic that we have coming from filed are multimode.
View 2 Replies
ADVERTISEMENT
Feb 27, 2012
We have two switches WS-C2960S-24TS-L running in stack with running IOS c2960s-universalk9-mz.122-55.SE3.We have connected two checkpoint devices on Gi1/0/24 and Gi2/0/24 with a simple configuration:
interface range GigabitEthernet1/0/24, gi2/0/24
switchport access vlan x
switchport mode access
spanning-tree portfast
On the devices log we get the following message:
%SW_MATM-4-MACFLAP_NOTIF: Host 0000.0000.fe21 in vlan x is flapping between port Gi2/0/24 and port Gi1/0/24
The mac-address 0000.0000.fe21 is not found on any checkpoint interface. "Show mac-address int gi1/0/24 or gi2/0/24" does not show the correct mac-address of the checkpoint interface connected to the port, but instead shows 0000.0000.fe21.Is there a bug in the IOS, something wrong with the switch config or does it have something to do with the checkpoint config?
View 2 Replies
View Related
Jul 24, 2012
I have a got a requirement where a 24 Port Switch should have 4 SFP's and all 4 should be used at a time, So I've chosen " WS-C2960S-24TS-L"
The transeiver should be GLC-LH-SM, so kindly let me no whether I would be able to use all 4 ports at a time or not.
View 2 Replies
View Related
Jan 3, 2012
I just received three WS-C2960S-24TS-Land three WS-C3560E-48TD-S switches that i entered the Express Setup on as usual. On two of each type of switch i found the default network that is used to facilitate the Express Setup was 10.0.1.1 and the others used an IP range of 10.0.2.1, i realized this is a small negligible at best difference though i need to provide management with an answer as to why there is a difference between the two and can’t find anything online as to why there is a difference or something that proves there should be a difference. All the documentation I find sounding Express Setup notes that the IP range will be 10.0.1.1 not 10.0.2.1
View 3 Replies
View Related
Dec 19, 2012
We have the following stack configuration:
Switch Ports Model SW Version SW Image------ ----- ----- ---------- ---------- 1 28 WS-C2960S-24TS-L 12.2(55)SE3 C2960S-UNIVERSALK9-M 2 28 WS-C2960S-24TS-L 12.2(55)SE3 C2960S-UNIVERSALK9-M 3 52 WS-C2960S-48TS-L 12.2(55)SE5 C2960S-UNIVERSALK9-M * 4 52 WS-C2960S-48TS-L 12.2(55)SE5 C2960S-UNIVERSALK9-M
View 5 Replies
View Related
Oct 23, 2012
I want to connect two linksys SRW2048 through fiber optic.. it's located different rooms with fiber optic....Is it possible through VALN....This setup using for CCTV connectivity?
View 1 Replies
View Related
Mar 20, 2012
How to get fiber optic modules for Cisco 2821 series router. I can not find anything apart a SFP module which contains only one SFP port.
View 9 Replies
View Related
Jul 23, 2012
When it comes to fiber optics my knowledge is very limited. All I know is that they can carry data at high bandwidth for a long range at blazing speeds etc.My boss has asked me to link several buildings to the network and I am led to believe that joining them through fiber optics to be best since we are expecting a lot of data traffic between.I have done the normal RJ-45 networking with Gigabit networking in my organisation but need your assistance on how to join each of the buildings through fibre optics.So far this is my plan.Draw up the fiber optic lines from the main building to each building.All the buildings have Gigabit Cat6e cabling and network in each.I am planning on using a single mode media converter to convert the end of the fibre optic to the normal RJ45 connector and plug it to each switch at each of the ends of the fiber optic cable .Am I going in the correct direction?I don't even know the gadgematics required except for the cables them selves, crimping tools, the media converter. There is about 300-400 metres in between of each building from the main building.Also, I believe that we need to create cross over cables as in the normal way we do in connecting 2 switches. Your input is very valuable to me.
View 9 Replies
View Related
Mar 17, 2012
Got 2 of these switch stacked and there is some changes that we are going to undertake which will require us to utilize the whole 8 or 4 (2 from each switch) SFP ports. Just need some adivce on which particular fiber modules should I procure. Does this switch support 10GB of SFP ?
View 7 Replies
View Related
Jan 24, 2012
I have 4 workstation at 4 different power substations. Each substation have switches. All substations is link with fiber optic cable throw switches. Each substation has 100 relay (IED) with different IP address it connect with substation switches. The IP address of substation is[CODE]
View 1 Replies
View Related
Oct 16, 2012
We have a stack of 4 Cisco WS-3750G-24TS with Sw Version 12.2(52) SE and giving weird errors:-
-Traceback= 17211C8 16FA4C0 16FA4FC 18625E4 18608D4 286A850 283E6FC 282EDF4 2859BBC 1B2EDA8 1B25878
Oct 17 22:26:48 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.7
Oct 17 22:26:50 AEDT: %SYS-3-CPUHOG: Task is running for (2098)msecs, more than (2000)msecs (8/6),process = SNMP ENGINE.
-Traceback= 172108C 17211CC 16FA4C0 16FA4FC 18625E4 18608D4 286A850 283E6FC 282EDF4 2859BBC 1B2EDA8 1B25878
Oct 17 22:26:51 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.7
Oct 17 22:26:53 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.6
Oct 17 22:26:53 AEDT: %SYS-3-CPUHOG: Task is running for (2097)msecs, more than (2000)msecs (1/1),process = SNMP ENGINE.
What are these errors is this a bug in the IOS
View 1 Replies
View Related
Feb 2, 2012
I need to compare a cisco ws-c2960s-24TS-s with a PowerConnect 6224, the scenario is to interconnect SAN ISCSI to 1G in RJ45.
View 1 Replies
View Related
Dec 18, 2012
I was looking at WS-C2960S-48FPS-L (740 Watts) and WS-C2960S-48LPS-L (340 Watts) models today, I'm not sure that I understand it right,
Does WS-C2960S-48FPS-L model support all 48 ports POE+ (30Watts)? Does that mean each port will get 30 Watts on this switch?
Does model WS-C2960S-48LPS-L support 24 ports with POE and 24 ports with POE+?.
View 4 Replies
View Related
May 28, 2012
How many Switches can be stacked with WS-C2960S-48FPD-L at a max..
As per my Knowledge it is 4 and as below..
Switch 1 to Switch 2
Switch 2 to Switch 3
Switch 3 to Switch 4
Switch 4 to Switch 1
If yes then, is it mandatory to do the "Switch 4 to Switch 1" stack. why am I asking this is because this stack requires a long cable and the cable which comes with the Switch is only 0.5M.
View 3 Replies
View Related
Mar 6, 2012
I am facing the following issue. In our environment we have a couple of WS-C2960S-24TS-L configured as stack. These switches are configured as VTP mode transparent.We are running LMS 4.1 and although UserTracking Acquisition works fine for all other switches, it only runs on demand for the above. The user tracking report for these switches shows only the MAC of the connected end hosts, without the respective IP address. The vlan I am interested in is configured on both the gateway (cisco 6509) and the switches, and the subnet is routable.Show arp on the gateway does show the "mac-ip address" binding, so I would have thought that usertracking would have been able to report both IP and MAC.
Why does usertracking only run on demand for the above switches in vtp mode transparent?Why does the UserTracking report show only the MAC and not the IP?Are the above issues related to the vtp mode? I have ruled out any connection to the switch-model, because we have recently installed the same switches in VTP mode client and User Tracking Acquisition works fine for them.
View 3 Replies
View Related
Apr 2, 2012
My company is beginning to have a lot of sites were we are stacking 3 to 4 C2960S-48 switche.This is making "show running-config" very very long because of the 4 x 48 interfaces.I can’t find a CLI command that show me the running-config of a ranges of interfaces. If I for example would like to see running-config for switch 3 (interfaces 3/0/1-52)The Show Running-config will show all the interfaces (for the two first swtiche = 104 interfaces), which take a time before I reach to switch 3.I miss a CLI command like: show Running-config switch 3, or module 3, or show running-config interface range x/x/x-x ?I’m well aware of the CLI command show running-config interface x/x/x, but this will only show me one interface.
View 3 Replies
View Related
Jul 20, 2011
My Storage supports RJ45 Connectivity. Some it gives slow performance. What if i connect all the Macpro using fibre optic and use some sort of converter to convert all the fibre connection to LAN. Will it increase performance?
View 2 Replies
View Related
Jun 26, 2012
I have a couple of questions concerning OM3 fiber optics <link snipped>. As i was searching for a vender to provide the cables needed for a job i have ran into OM2 & OM3 fiber patch cords. Besides the color difference, is OM3 the new revolutionary cable type being used now and days? The specs i have seen between the 2 are quite similar, both are 50 microns
View 3 Replies
View Related
Jul 13, 2011
I am going to design a network of an University.I want solution completely on cisco
View 2 Replies
View Related
Jul 23, 2012
When it comes to fiber optics my knowledge is very limited. All I know is that they can carry data at high bandwidth for a long range at blazing speeds etc.My boss has asked me to link several buildings to the network and I am led to believe that joining them through fiber optics to be best since we are expecting a lot of data traffic between.I have done the normal RJ-45 networking with Gigabit networking in my organisation but need your assistance on how to join each of the buildings through fibre optics.Draw up the fiber optic lines from the main building to each building.All the buildings have Gigabit Cat6e cabling and network in each.I am planning on using a single mode media converter to convert the end of the fibre optic to the normal RJ45 connector and plug it to each switch at each of the ends of the fiber optic cable .I don't even know the gadgematics required except for the cables them selves, crimping tools, the media converter. There is about 300-400 metres in between of each building from the main building.Also, I believe that we need to create cross over cables as in the normal way we do in connecting 2 switches.
View 1 Replies
View Related
Jul 8, 2012
Our network administrator restricts all our new 1Gb switches to only 100Mb, to which he claims it will increase overall performance. Preventing devices from bottlenecking the network. (that is, only restricting the main switch ports, not the uplinks)For example we have a new building with 2x WS-C2960S-48TS-L connected together with FlexJack and then a 1Gb Fiber connection back to our core switch.
This building is on it's own subnet and there is little broadcast traffic. I don't see the point other than it hinders the potential speed we could use. Labs are set up in this building and 1Gb is MUCH faster when it comes to imaging and software deployment.
View 8 Replies
View Related
Apr 26, 2012
We're planning to install 24 strand singlemode fiber optic cable in three ocations. What is the best way to run the cables between the 3 locations. Location 1 is in the south, 2 is in the middle and 3 is in the north pretty much in a straight line.Should we run one fiber optic cable from location 1 to location 2 and another fiber optic cable from location 1 to location 3 or is there a better way? Maybe we can run from 1 to 2, 2 to 3 so that location 2 acts like a hub.Is there a way to just run one fiber optic cable from location 1 to 3 and along the way somehow splice that cable to go to location 2
View 1 Replies
View Related
Jan 14, 2013
I need Know what connection is using on Cisco 2811 router.I have this interface in Cisco 2811, I need Know if this port is connected to Fiber or Copper. I think is copper with RJ45 but I see 100 base TX/FX so this make me doubt about it because TX its for copper link and FX for fiber. [code]
View 5 Replies
View Related
Sep 7, 2011
how we can combine the LAN and Wimax connections? We are using here in our office one Fiber optic line that is running fine and we want to make up a backup connection of Wimax or wireless, how we can combine these two connections ,Moreover we are using here D-Link firewall and Netgear FS-726T Router.
View 3 Replies
View Related
Jul 3, 2011
Currently we have a cisco router 2801 for Wireless Internet connection. And we are going to have another ISP that can provide us Fibre Optic internet connection rather than wireless.My question is that can we use this router for fibre optic internet connection? how do we go about this? what is the maximum bandwidth that the router can support?
View 8 Replies
View Related
Feb 27, 2013
I got new internet last Thursday. It is fiber optic through VTX1. I am running windows 7. I can connect to the internet just fine directly but when I try the netgear it tells me No Internet Connection. When I go through the setup process it tells me No Ethernet Cable is Plugged Into The Router Internet Port. When I hook up my very old Cisco router the internet and Wi-fi work just fine. I have updated the drivers and have windows firewall off. This is it plugged directly in:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersKellan>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Kellan-PC
Primary Dns Suffix . . . . . . . :
[code]....
View 2 Replies
View Related
Sep 30, 2011
correct settings > Configuration of WAG54G2 on etisalat adsl fiber optic
View 1 Replies
View Related
May 21, 2013
Has anyone configured Layer 3 port channel on Cisco 6509 switches which are connected over dark fiber between two buildings?
View 3 Replies
View Related
Mar 22, 2012
Company I work for just moved into a new location. We have two data closets which are patched as independent entities, with no Ethernet tie connection. These closets are roughly 100 feet apart.
There is a fiber connection that runs between both closets, that the previous tenant used to connect the switches. I have placed a Cisco 2960 switch in each location, and added one mini SFP gbic's to each switch. After attaching both sides, neither light up. I do a sh inter gig1/0/49 on each and shows 'down down' (not admin down).
What is the trick on getting these to communciate, do I need to configure these ports, and are they supposed to light up?
What I am trying to accomplish is to get the one closet that is completely cut off, communicating by logically stacking, or 'daisy chaining' via fiber.
I turned off the lights and popped the fiber out, and I do see a faint red light (I did not look straight into it), so I think the fiber is active.
View 2 Replies
View Related
Nov 3, 2011
I have three switches:
primary - Cisco Catalyst 3750G-24TS-24
and two SG300-28
I need to apply uplinks as follows:
3750G-24TS-24 SFP (1) -> SG300-28 (first) mini-GBIC (1)3750G-24TS-24 SFP (2) -> SG300-28 (second) mini-GBIC (1)SG300-28 (first) mini-GBIC (2) -> SG300-28 (second) mini-GBIC (2)
I would like to know, What type of mini-GBIC and SFP and cable I should use for SX Multimode?What max speed rate I will get?
View 8 Replies
View Related
Jul 18, 2011
I have issue with connectivity 3750G with Dlink Switch, it cannot connect to non-cisco switch with fiber , But CISCO to CISCO switch it shows connectivity. My question is that is there any configuration on Cisco 3750G switch to connect with non-cisco switch through fiber (SFP) ?
View 2 Replies
View Related
Feb 14, 2013
We have a scenario where we want to connect 14 access layer 2950 switches to Core switch 3750 via optical fiber in a LAN.What model of 3750 Switch should we use to tackle this situation.I have learnt that WS-C3750X-24P should support it.Isnt it?
Can we use optical fiber SFP module to connect 2950 switches to core switch?Does Cisco 2950 Switch support optical fiber sfp module?
View 2 Replies
View Related
May 25, 2013
I need to connect 4 Floor Building with 4 Cisco 2960 - 48 ports switch each other and it needs to be through a fiber. So all PCs connected to each switch would reach the LAN/WAN from the other switch. (attached is the image here with)
I see that the 2960 has 2 SFP ports each port of each switch should connect each other or how?
My simple question is:
1. What cable / patch code I have to use = Single-mode or Multimode? ( distance for each switch will not more then 25 mts)
2. Do I have to use SFP or SFP+ module?
3. What kind of SFP/SFP+ module I have to use = Single-mode or Multimode?
4. What kind of connector should patch code have = LC / SC or ?
5. How to connect each switch with redundancy like ...each switch should be interconnected with each other or I have to choose Cisco 3750G which has more then 2 SFP ports (option#1 & opetion#2 = attached here with) =
Best practice for connecting cisco switches over fiber.
View 10 Replies
View Related
