how we can combine the LAN and Wimax connections? We are using here in our office one Fiber optic line that is running fine and we want to make up a backup connection of Wimax or wireless, how we can combine these two connections ,Moreover we are using here D-Link firewall and Netgear FS-726T Router.
View 3 RepliesMy Storage supports RJ45 Connectivity. Some it gives slow performance. What if i connect all the Macpro using fibre optic and use some sort of converter to convert all the fibre connection to LAN. Will it increase performance?
View 2 Replies View RelatedI have a couple of questions concerning OM3 fiber optics <link snipped>. As i was searching for a vender to provide the cables needed for a job i have ran into OM2 & OM3 fiber patch cords. Besides the color difference, is OM3 the new revolutionary cable type being used now and days? The specs i have seen between the 2 are quite similar, both are 50 microns
View 3 Replies View RelatedI am going to design a network of an University.I want solution completely on cisco
View 2 Replies View RelatedWhen it comes to fiber optics my knowledge is very limited. All I know is that they can carry data at high bandwidth for a long range at blazing speeds etc.My boss has asked me to link several buildings to the network and I am led to believe that joining them through fiber optics to be best since we are expecting a lot of data traffic between.I have done the normal RJ-45 networking with Gigabit networking in my organisation but need your assistance on how to join each of the buildings through fibre optics.Draw up the fiber optic lines from the main building to each building.All the buildings have Gigabit Cat6e cabling and network in each.I am planning on using a single mode media converter to convert the end of the fibre optic to the normal RJ45 connector and plug it to each switch at each of the ends of the fiber optic cable .I don't even know the gadgematics required except for the cables them selves, crimping tools, the media converter. There is about 300-400 metres in between of each building from the main building.Also, I believe that we need to create cross over cables as in the normal way we do in connecting 2 switches.
View 1 Replies View RelatedWe're planning to install 24 strand singlemode fiber optic cable in three ocations. What is the best way to run the cables between the 3 locations. Location 1 is in the south, 2 is in the middle and 3 is in the north pretty much in a straight line.Should we run one fiber optic cable from location 1 to location 2 and another fiber optic cable from location 1 to location 3 or is there a better way? Maybe we can run from 1 to 2, 2 to 3 so that location 2 acts like a hub.Is there a way to just run one fiber optic cable from location 1 to 3 and along the way somehow splice that cable to go to location 2
View 1 Replies View RelatedWhen it comes to fiber optics my knowledge is very limited. All I know is that they can carry data at high bandwidth for a long range at blazing speeds etc.My boss has asked me to link several buildings to the network and I am led to believe that joining them through fiber optics to be best since we are expecting a lot of data traffic between.I have done the normal RJ-45 networking with Gigabit networking in my organisation but need your assistance on how to join each of the buildings through fibre optics.So far this is my plan.Draw up the fiber optic lines from the main building to each building.All the buildings have Gigabit Cat6e cabling and network in each.I am planning on using a single mode media converter to convert the end of the fibre optic to the normal RJ45 connector and plug it to each switch at each of the ends of the fiber optic cable .Am I going in the correct direction?I don't even know the gadgematics required except for the cables them selves, crimping tools, the media converter. There is about 300-400 metres in between of each building from the main building.Also, I believe that we need to create cross over cables as in the normal way we do in connecting 2 switches. Your input is very valuable to me.
View 9 Replies View RelatedI have 4 workstation at 4 different power substations. Each substation have switches. All substations is link with fiber optic cable throw switches. Each substation has 100 relay (IED) with different IP address it connect with substation switches. The IP address of substation is[CODE]
View 1 Replies View RelatedI got new internet last Thursday. It is fiber optic through VTX1. I am running windows 7. I can connect to the internet just fine directly but when I try the netgear it tells me No Internet Connection. When I go through the setup process it tells me No Ethernet Cable is Plugged Into The Router Internet Port. When I hook up my very old Cisco router the internet and Wi-fi work just fine. I have updated the drivers and have windows firewall off. This is it plugged directly in:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersKellan>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Kellan-PC
Primary Dns Suffix . . . . . . . :
[code]....
Currently we have a cisco router 2801 for Wireless Internet connection. And we are going to have another ISP that can provide us Fibre Optic internet connection rather than wireless.My question is that can we use this router for fibre optic internet connection? how do we go about this? what is the maximum bandwidth that the router can support?
View 8 Replies View Relatedcorrect settings > Configuration of WAG54G2 on etisalat adsl fiber optic
View 1 Replies View RelatedI want to connect two linksys SRW2048 through fiber optic.. it's located different rooms with fiber optic....Is it possible through VALN....This setup using for CCTV connectivity?
View 1 Replies View RelatedHow to get fiber optic modules for Cisco 2821 series router. I can not find anything apart a SFP module which contains only one SFP port.
View 9 Replies View Relatedfind out which types of fiber optic that i can connect to three types of switches. the setup that i have that there are:8 access switches (WS-C2960S-24TS-S), in each one there is two SFP connections.2 aggregate switches WS-C3750X-24T-S, in each one there is four SFP connections.and one core switches that has SFP card WS-X4624-SFP-E? Note that the fiber optic that we have coming from filed are multimode.
View 2 Replies View RelatedRecently I have had a thought about changing the networking around my house.urrently we have two routers as my house is very tall and not very wide, they are called JohnsonNet1 and JohnsonNet2. Is there a way to get them to run one network called JohnsonNet?
View 3 Replies View RelatedI am getting ready to move into new digs and wanting to set up my network. Main house cable internet will come in with modum to a dlink router for both wired and wireless. desktop and a magic jack wired into router wireless for ipad and laptop. then run wire to workshop about 100' from house where a second magic jack and desktop will be set up (small biz out of workshop). I am pretty sure that the range of the router for wireless will reach to workshop fine for ipad but if not I will need to put a wireless up there tooext kids have a laptop running windows 7 but kids being kids and having had problems with self control on net in past I want to be able to make sure that I can turn them off from net when needed because
1. I do not want them running me past the data limits imposed by cable company and
2. keep them from sites such as those which got them in trouble in the past (kids are older and bought laptop for selves and pop will not go along with me confiscating it if they abuse internet privileges
I've recently upgraded to windows 8 and I've been having some issues with my wireless connectivity. I've narrowed it down to an issue with the wireless adapter. Specifically, windows doesn't seem to recognize my Intel centrino Advanced-N + WiMAX 6250 and instead installed drivers for Intel Centrino Advanced-N 6250 AGN. The correct driver is instead listed in "Other Devices" in the device manager.
[URL]
I am looking to expand my network. I purchased a WD N900 router to replace my old Linksys E1200 .The internet connection is coming from the modem, into the WD N900 Router. The WD N900 has the printer hooked up to it, and 3 NAS, a computer and our magic jack. I ran 30 feet of network cable and routed the cable through the walls into the section of the house. I am looking to use my old Linksys E1200 to extend my network. I want to hook up the gaming systems (PS3, XBOX360) as well as the entertainment receiver to my Linksys router. What is the best setup? I am looking to be able to access the NAS from the WD N900 on our PS3 and Xbox360 so LAN-LAN looks like the way to go. I tried using the directions on Linksys site, but it doesn't seem to want to work. I test the network cable I ran through the walls, and it is getting a good signal. However when I hook it up to the Linksys E1200 and connect my lap top the Linksys E1200 to test it isn't working.
View 6 Replies View RelatedRegion : Philippines
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP : Smartbro WiMax
I'm using the router TL-WR2543ND, I have pesonally configured the router myself, I'm no that good in computer but I managed to do so. I never had difficulty doing it. I have decided to switch to Smartbro Wimax and tried to connect it to my tp-link router but no luck. I browsed the net for possible instructions to do it but just frustrates me. I have changed the IP address of the router to avoid conflict, cloned the MAC address, still unable to connect the router.
I have 2 campuses. I have my 5508 wireless controller working beautifully on my main campus using LDAP. (YAY!!) Now for my problem. My remote campus has 1310 bridges. I was able to successfully upgrade one of them to work with the controller, however, I can't get the other two bridges to talk to the one that I upgraded and I can't get them to upgrade, it indicates that they need to be the root. I have several small buildings on that remote campus, than need that remote bridging in order to be able to have network access.
View 7 Replies View RelatedI have a server running win2000 server managing a network of 30 computers, it als a proxy server where all pc connecting to for internet access. The server is connected to Wimax through a router. Lately i have a vpn for PDA's through GSM lines where am supposed to connected a Modem (part of VPN)to this server so that PDA' s and modem can be on the vpn.The problem is that when I connected the GSM Modem the internet connection through router get disconnected. How do I connect the modem on the server without disconnecting the wimax internet connection
View 3 Replies View RelatedAs I know both wimax and wifi are use for wireless network.But what is the major points of difference between them?
View 3 Replies View RelatedAt my office, I have two ISPs. Here is the configuration:
ISP1:
- Firewall > Switch > LAN 192.168.10.xxx
- Wireless Router1 Connected to Switch above > WLAN 192.168.10.xxx
ISP2:
- Wireless Router2 connected directly to main RJ-45 jack coming from ISP2
- WLAN 192.168.1.xxx
ISP1 is a T1 line bundle. It was slow for our wireless users in the office. So we went ahead and signed up a cable internet connection from ISP2. The one and only one device connected to ISP2 jack is a wireless router (Wireless Router2).People who are connected to Wireless Router2 (192.168.1.xxx) can't see anything in our LAN and WLAN (192.168.10.xxx); for example Domain Controller, Printers, File Server, etc.How can I configure ISP2 setup so that both routers (or you can say both ISPs) are on the same network 192.168.10.xxx? I want to do this so everyone is on the same network and can see everything.
I have this laptop with a built-in Intel Centrino Advanced-N + Wimax 6250 adapter to connect to WiMAX.Right now I have a WiMAX connection at home with a simple gateway. So what I want to do right now is trying to connect to this network using my built-in adapter.I'm facing right now is that the driver of the adapter only searchs for a certain provider from the US (Clear). I'd like to subscribe to their service but I live in Argentina so that's not a valid option. So my question is if you know of a custom driver or some other way to search for my local wimax network.
View 1 Replies View RelatedI've got the Di-614+ connected to a Wimax system. The Wimax is plugged into one of the LAN jacks in the Di-614+ (i tried pluggin it into the WAN jack but it does not work). I'm able to use the internet fine without any problems using the wireless connection on my laptop.
The thing is the ip 192.168.1.1 is set to open up the setup page of my Wimax modem. I cant seem to access the setup page of my Di-614+. I tried disconnecting the Wimax jack, and still google chrome just responds with "This webpage is not available". My other option is to hard reset the wireless router. But i worry it will ask for a password and i wont know it.
Region : UnitedStates
Model : TL-MR3040
Hardware Version : V1
Firmware Version : latest
ISP : Freedompop / Clear
How to get this router running with wimax usb from either Freedompop, Virgin, Clear , or Sprint?
The fastest dsl speeds here is 1.5mbpsand I need something around 3mbps+. I'm curious if I could buy two 1.5 connections from my ISP and connect them both into a router and then hook a switch up to it and connect my PCs and everything to it to get 3 or if I would still just get the 1.5?
View 4 Replies View Relatedi have have lan in the office(internet installed) and i want to combine it with the lan in the computer lab for internet .i dont want to use cable as it might be too long .
View 1 Replies View RelatedI am trying to work out a way of combining two networks from two (Internet Service Providers or ISPs. One network is for Internet, and the second one is for CCTV cameras. Both networks exist and are working independently, each with its own servers. I want to re-design the whole system such that at any one time t, a supervisor with an Internet connection in his office can be able to see what is happening on cctv cameras without contacting the cctv personnel.
View 6 Replies View RelatedI have two different Internets from different ISPs can I intgrate in one to increase total bandwidth. (means 2+2=4)
View 1 Replies View RelatedI have 2 x PC and 3 x laptops. Currently the 2xPCs are connected by ethernet LAN and a printer through a 5-port switch. Would it be possible to add a router into the system somewhere so that the 3xlatops can access the network?
View 2 Replies View RelatedI have a Wimax internet connection via an ethernet cable from a small roof top receiver dish. Inside the house the cable (RJ45) is plugged into the POE slot on one side of a small electrically powered black box, and from the other side, an ethernet cable (RJ45), connects to my PC. I want to share my internet connection with my HTC mobile and would prefer to make use of an existing Belkin 54g ADSL2 modem/wireless router (Belkin F5D7633) if I can. As this router's incoming port is specifically for ADSL my internet RJ45 cable can not plug into it. I have been advised that I can still utilise the router part of the Belkin though, using my PC as an access point, by plugging the ethernet cable from the PC side of the little black box into LAN 1 on the router, then joining the PC to LAN 2 of the router with another ethernet cable.I did not alter the configuration of the Belkin at all (having reset factory defaults beforehand), mainly because although I could access the internet from my PC and my mobile, I could not access the IP address of the router, presumably because the properties of the local area connection on my PC remained unchanged with the IP address (172.168.1.149), Subnet Mask (255.255.255.0), Default Gateway (172.168.1.1) and 3 DNS addresses (172.168.1.1) (10.30.0.1) (8.8.8.8) as they were before hooking up the Belkin. The IP address the mobile received through WIFI on connecting to the Belkin was 172.168.1.148
I was not unduly concerned about not being able to access the configuration of the router as everything was working as I had hoped it would and even when I powered off my PC I still had internet access on my mobile. On rebooting the PC, however, I found that the router changed the DNS addresses on the PC to 2 only, both identical (192.168.2.1) and the IP on the mobile was allocated 192.168.2.2 Although I could still access the internet on my PC, I no longer had access from my mobile although the WIFI connection to the Belkin showed as being 'excellent'. When I did a 'repair' of my internet connection, hoping to revert to a fully operative state, the PC configuration changed again as follows: IP address becomes that of the router (192.168.2.1), Subnet Mask (255.255.255.0), Default Gateway (192.168.2.1), 2 DNS addresses (192.168.2.1) and the IP address allocated to my mobile remains (192.168.2.2) This configuration means I have no internet access from either PC or phone, but CAN access the router configuration. I restored a usable operating state by unplugging the power from the router, transposing the cables in the LAN ports on the router (swapped cable from LAN1 to LAN2 and vice versa), turned off WIFI on mobile and waited a minute or two. When I powered the router back up and switched on mobile WIFI again, everything was restored to the original working state and I have, once again, access to internet on both PC and mobile. It is very frustrating, however, to keep performing this ritual and I wonder if any of you more technically minded, know a way to work around this, perhaps by manually changing the configuration of PC or router?
i have wimax usb modem and tenda wifi router with rj45 ports.
View 5 Replies View Related