Cisco Switching/Routing :: 3750 - 24TS / PAgP Port In Stand-alone Mode
Mar 23, 2013
Devices are 3750-24TS Switches, software version is 12.2(55)SE6. how to troubleshoot this issue, I have a pair of ports which are not bundling, no matter what. Is the same behavior with LACP or PAgP. In this outputs I have only the PAgP case.
Output is similar to:
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
12 Po12(SD) PAgP Fa1/0/23(I) Fa1/0/24(I)
Configuration on ports is simple:
SW1:
interface FastEthernet1/0/24
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 12 mode desirable
[code]....
View 3 Replies
ADVERTISEMENT
Nov 15, 2012
What should the duplex mode to be set on a routed port gi0/21 that are running HSRP ? I try setting the gi0/21 to full, but it caused the port to be down. The only way for the port to be up is setting it to half duplex.
Cisco 3750 Switch
==============
interface GigabitEthernet0/21
no switchport
ip address 10.200.104.34 255.255.255.248
[Code].....
View 2 Replies
View Related
Nov 15, 2012
I am confused about some things regarding the different IOS versions and their compatibility with certain switch hardware. I understand the differences between the IPBASE and IPSERVICES ios but am not quite clear as to how you can tell which ios images will work on which Cisco switch model platforms, other than the fact that some switches are designed only to run the IPBASE images and others have advanced hardware to run the advanced images. For instance, if I have a 3750-24TS-E with an IPBASE ios on it, can I load an IPSERVICES ios that came from say a 3750G-24TS-E1U? whether the ios on one platform can be transferred to another?
View 5 Replies
View Related
Jan 30, 2012
WS-C3750G-24TS-S1U switch stack with high CPU utilization. 3 switches are stacked and using PBR on that. I am attaching the show cpu process as an attachment.The current template is "desktop routing" template.The selected template optimizes the resources in the switch to support this level of features for 8 routed interfaces and 1024 VLANs. [code]
View 0 Replies
View Related
May 21, 2012
We have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
View 11 Replies
View Related
Jan 13, 2012
I think that a catalyst3560X connect to VSS Catalyst 6509 by ether-channel.
I'd like to connect a catalyst3560X to VSS Catalyst6509 by the Ether-channel.
I heard need "Enhanced PAgP" that VSS Catalyst6509 connect to by Ether-Channel.
I don't know supported "Enhanced PAgP" on Catalyst3560X.
View 6 Replies
View Related
Jul 7, 2012
use PAGP as backup for wireless link with another wireless link.
__WiFi________
PC-------Switch 1 Switch2---------- PC
__WiFi________
We are using 2960 series and from this reason we cant use L3 PAGP I dont know how is PAGP working. If it is checkung port status (UP/Down) or there are some specific L2 packet between etherchannel ports in group?
View 5 Replies
View Related
Oct 15, 2012
I have the Cisco VSS consisting two chassis 6509.I have the system Active-Dual detection via Enhanced PAgP with one neighbor - standalone cisco 3750. All works good.I want to add one more neighbor - cisco stack 3750x with 3 members. Will this scheme work? And what is in danger, if the stack is split into two parts?
View 2 Replies
View Related
Nov 16, 2011
Im looking for some clarification regarding running a Cisco ASA in transparent mode with multiple contexts. To give you an insight into the network design we have the following -
Collapsed Core/Aggregation Layer running Cisco 3750s. The 2 Cisco 3750s are using SVIs with HSRP for default gateways per customer with a total of 8 customers. Each customer is segregated into seperate VLANs with Cisco 2960 switches used in the Access layer. Each customer has 2 Cisco 2960 switches with redundant uplinks to the Core/Aggregation layer. Customers are spanning tree loadbalanced between core/aggregation switches.
What i need to now do is add two transparent firewalls into the mix in either an active/active or active/standby setup. I need the firewalls to support all 8 customers, therefore I am guessing they need to run in multiple context mode. Having read into this it has left me somewhat confused as to how to integrate them into the above setup as a bump in the wire so to speak.
View 2 Replies
View Related
Mar 5, 2012
I'm looking for switches that support single mode fiber connections and would like to know if "WS-C3750-FS-S Catalyst 3750 24 100BaseFX + 2 SFP" and "WS-C3750G-12S-S Catalyst 3750 12 SFP" can serve the purpose?
View 6 Replies
View Related
Jun 19, 2012
A multisite network is currently supporting muticast using PIM dense mode, which is enabled on router/switch LAN and WAN interfaces across all locations. I am about to introduce Nexus switches to the main LAN. How can I make dense and sparse mode coexist to ensure flow of muticast traffic between devices supporting and dense and sparse mode? Eventually, I want to transition to the sparse mode; however, it has to be done gradually, even within a single site. The leacy equipment includes Cat 3750 and 4500s.
View 2 Replies
View Related
Jan 16, 2013
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies
View Related
Jun 4, 2012
I am troubleshooting a fiber connectivity issue.Now I have two switches, one is 3750, and another is small biz 300 series switch. Both switch has a single mode smf gbic. Now I have two swtiches face to face and connect with a single mode cable. Do you think if I would get a link light on? Both ports are no shutdown.
View 3 Replies
View Related
Sep 12, 2012
I have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies
View Related
Oct 28, 2012
Will i need another RFS6000 controller to run a single AP650 (isolated remote location) or it can be set in stand-alone mode ? I might consider install one antenna per location in 5 different store.
View 6 Replies
View Related
May 2, 2012
We are deploying a new office and exploring the options for WLAN deployment. We were pretty impressed with 3500 series APs and that it supports CleanAir.However, we have decided to go for standalone AP deployment model now. As 3500 does not work in standalone mode, so we are looking for APs that can work in standalone mode ( and later can be converted to lightweight if needed). We can go for 1140 in that case. However, it would be better for us to know the main differences between features supported by 3500 lightweight AP and 1140 standalone AP. CleanAir looks like the main one. Are there other important ones as well?
View 2 Replies
View Related
Feb 17, 2012
I have the following switch:
#show version
Cisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(52)SE, RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Image text-base: 0x01000000, data-base: 0x02C00000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
[code]...
I have downloaded c3750-ipservicesk9-mz.150-1.SE2.bin and I want to upgrade iOS to this image.
I have a few questions related to this:
1. Is my switch model compatible with this iOS version?
2. Do you recommend the upgrade? Does it bring some notable features?
3. Can I upgrade for free or do I need to buy some license?
4. I also want to upgrade/add the crypto image, can I add crypto for free or some license is required?
5. I have remote access to my switch via the console cable which plugged into machine1. But machine1 is connected to network via the same switch. I am accessing machine1 via SSH, and then the switch via console cable (minicom on CentOS). Is there an upgrade procedure for this kind of situation that also has some fall back (like reboot in X minutes and load the previous image) if the upgrade goes wrong?
View 6 Replies
View Related
May 19, 2013
I have a stack of 4 3750 Switches.
1. WS-C3750G-12S
2. WS-C3750G-12S
3. WS-C3750X-48P
4. WS-C3750X-48P
The stack cable connected to Switch 1 Port 1 and Switch 4 Port 2 will not come back online. The logs show that there was a Stack line change. I have replaced the 1 meter Stack cable from Switch 1 to Switch 4 three times and it still does not come back online. This is the part that is interesting.. I have disconnected Port 1 Switch 4 and connected it to Port 2 Switch 4 and then Switch 4 came back online. This made me think Port 2 on Switch 4 was working correctly. Then I disconnected Port 2 Switch 1 and connected it to Port 1 Switch 1 and then Switch 1 came back online.
View 1 Replies
View Related
Mar 11, 2013
have a cable i think is bad, is it possiable to switch the cable out without causing any downtime to the switch or connected devices?
HQ-1st-Flr-Stack#show switch stack-ports summary
Switch#/ Stack Neighbor Cable Link Link Sync # In
Port# Port Length OK Active OK Changes Loopback
Status To LinkOK
[Code].....
View 15 Replies
View Related
Nov 7, 2011
I am trying to configure a 3750 48 port switch and having trouble with getting it to see the sfp. I just want to set up the router with a pretty basic set up since I am using it for a ping test between 2 buildings, via fiber. How I can enable the sfp port?
View 3 Replies
View Related
Mar 6, 2012
I am facing the following issue. In our environment we have a couple of WS-C2960S-24TS-L configured as stack. These switches are configured as VTP mode transparent.We are running LMS 4.1 and although UserTracking Acquisition works fine for all other switches, it only runs on demand for the above. The user tracking report for these switches shows only the MAC of the connected end hosts, without the respective IP address. The vlan I am interested in is configured on both the gateway (cisco 6509) and the switches, and the subnet is routable.Show arp on the gateway does show the "mac-ip address" binding, so I would have thought that usertracking would have been able to report both IP and MAC.
Why does usertracking only run on demand for the above switches in vtp mode transparent?Why does the UserTracking report show only the MAC and not the IP?Are the above issues related to the vtp mode? I have ruled out any connection to the switch-model, because we have recently installed the same switches in VTP mode client and User Tracking Acquisition works fine for them.
View 3 Replies
View Related
Dec 6, 2011
I have stacked WS-C3750E-24PD with Ten Gigabit Ethernet ports configured under ether-channel. It has c3750e-universalk9-mz.122-55.SE1.bin IOS installed on it. One of the Ten Gigabit Ethernet ports, goes to err-disable mode with following errors on that specific ports.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm. (DROmx-1-1)
I have gone through some of CSC forums like {URL}. The workaround is to "Remove the X2 or SFP from the inactive up link port" which is not in my case.
View 9 Replies
View Related
Feb 6, 2012
I'm troubleshooting interface drops. However the output of the following show commands don't match number of drops. Based on the output, can you find out what is causing the drops? the G1/0/28 is the uplink. Is that just the port got overrun by the traffic?
#show int g1/0/28
GigabitEthernet1/0/28 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0019.5667.191c (bia 0019.5667.191c)
[Code].....
View 7 Replies
View Related
Feb 27, 2012
We have two switches WS-C2960S-24TS-L running in stack with running IOS c2960s-universalk9-mz.122-55.SE3.We have connected two checkpoint devices on Gi1/0/24 and Gi2/0/24 with a simple configuration:
interface range GigabitEthernet1/0/24, gi2/0/24
switchport access vlan x
switchport mode access
spanning-tree portfast
On the devices log we get the following message:
%SW_MATM-4-MACFLAP_NOTIF: Host 0000.0000.fe21 in vlan x is flapping between port Gi2/0/24 and port Gi1/0/24
The mac-address 0000.0000.fe21 is not found on any checkpoint interface. "Show mac-address int gi1/0/24 or gi2/0/24" does not show the correct mac-address of the checkpoint interface connected to the port, but instead shows 0000.0000.fe21.Is there a bug in the IOS, something wrong with the switch config or does it have something to do with the checkpoint config?
View 2 Replies
View Related
Jan 2, 2013
getting CPU utilization around 62%
CPU utilization for five seconds: 54%/6%; one minute: 61%; five minutes: 61%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
35 82081 9642 8512 0.31% 0.21% 0.18% 0 Compute load avg
[Code]....
View 1 Replies
View Related
May 9, 2013
I have problem with my cisco switch 2970.
Initializing flashfs...
flashfs[1]: 5 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 5935616
[Code]...
View 2 Replies
View Related
Jul 24, 2012
I have a got a requirement where a 24 Port Switch should have 4 SFP's and all 4 should be used at a time, So I've chosen " WS-C2960S-24TS-L"
The transeiver should be GLC-LH-SM, so kindly let me no whether I would be able to use all 4 ports at a time or not.
View 2 Replies
View Related
May 1, 2012
how to reset password on WS-C3560G-24TS?
View 1 Replies
View Related
Jun 18, 2012
I have configured SPAN in cisco 3750 switch as below mentioned. but the destination port protocol is down.switch(config)#monitor session 1 source interface gigabitethernet1/0/1switch(config)#monitor session 1 destination interface gigabitethernet1/0/11 ingress vlan 1
View 8 Replies
View Related
Dec 12, 2011
Been dealing with a strange problem for several days now. It started out with a problem that I thought was VTP related but ended up being something else. I setup a span port on a 3750 that I am connected to that was mirroring the trunk connection coming into the switch.
Never saw an VTP traffic come across the connection but doing a sh vtp status indicated the traffic was arriving and getting processed. When I found some debug commands (debug sw-lan vtp), I was also able to see the packets go between switches. Seeing this issue concerns me that there is other traffic that isnt showing up during a span session.
I know that doing a span on a switch, especially using a trunk port as a source, isnt a good idea. Since I didnt have a TAP at time, this was my only choice. I have since borrowed a NetOptics TP-CU3 tap from a good friend and was able to confirm the VTP traffic was going across the trunk connection between switches.
All of my 3750's are running 12.2.55.SE.
View 8 Replies
View Related
Dec 7, 2011
I have 3750 core/distribution switches with routing enabled in two offices connected with copper link and L3 port channel interfaces. NewOffice#2 has moved about 5 miles farther away from office#1 and I have to deploy new core/distribution switch connect it to old core#2 via F.O and move all access switches with it. Old core will stay in old #2 offices as a bridge between office#1 and new office#2 Office#1core<->copper (Ethernet) <->oldoffice#2core<->f.o. <->new office#2core How I should configure port channels ports on oldoffice#2 core to act as bridge between office#1 core/dist and newoffice#2 core/dist without changing anything else (ip, etc) on whole network
View 1 Replies
View Related
Apr 15, 2012
There 's a Cisco IP phone that sits between a PC and the switch port. On the switch port, no MAC address is learned. However, the switch is able to detect the IP phone and deliver power to it: [code] Switch is Catalyst 3750 with IOS version 12.2(58)SE1.
View 1 Replies
View Related
Jun 5, 2012
We have several 3750 stacks across our campus that we are unable to completely clear port security on. We have mac address stick set up on all access ports. When we clear the sticky address on the port, the mac address is removed from the running config like normal, but we keep getting port-security voilations. If port security is taken off the port completely, i.e. no switchport port-security, traffic still doesn't pass the port. Even clear port security across the stack doesn't work. If we try to reload the stack, only the master reboots, and the other switches in the stack lose switch capabilities.
View 1 Replies
View Related
