I try change the configuration the port in the switch catalyst express 500, i need disable switch port port-security, a try with http://10.1.1.1/exec and save configuration with wr command, if a check the configuration de port is correct but i reboot the switch and check the configuration the port appear the switch port port-security configuration again.
View 3 Repliesconfigure port security Cisco 500 Swich ? There is no CLI mode in this switch?
View 2 Replies View RelatedIm trying to follow along documentation i see via train single videos and some online resources. I am trying to enable port security.I have a Catalyst 3546 XL when i type in "rtr1# switchport ?""port-security" is not only of the options to choose from. I have already set this as an access port.
View 4 Replies View RelatedOur customer has a Cisco ME3600X with the IOS me 360x-universalK9-mz.122-52.EY3.They are saying that is not possible to configure the "switchport port-security mac-address sticky" in the interfaces and want to know whether any additional license is needed.As far as I know there isn't any extra license to activate this feature and also I believe the ME3600 switch should have this feature with the universal IOS, isn't that right?
View 1 Replies View RelatedI am trying to factory reset CE500 switch, as described in the factory rest section of the documentation. I do not get an IP address via DHCP from the switch.
On boot up I hold the setup button down, wait till the lights go solid amber release setup. wait for a port on the switch to start blinking green port 1 starts blinking green, plug my pc into port and wait for IP..and keep waiting !!!!
I have tried this on 3 switches now all with the same result.... NO IP offered.
For any still having trouble with the intial config of a CE500 Switch using Windows 7 / Vista...
Sure all of you have heard of the setup button and how to use it, its obvious Windows 7 / Vista do not properly recieve the DHCP, maybe an issue with the some new Microsoft legislation, the install address of the device in its setup phase, which you can read by the setup led burning steadily is 169.254.0.1
You wont be able to connect to this address in Windows 7 / Vista if you configure it statically, you will be able to view the Gratituous ARP from the Device using Wireshark, in the Windows 7 / Vista network adapter tci/ip v4 settings click on the advanced tab, there enter 169.254.0.1 as the default gateway, press the Setup button on the switch, wait for it to blink, connect your utp cable to port 1 check that the Setup LED is burning stable, type 169.254.0.1 into your web browser and enter a management IP address for the switch, alternatively use Cisco Network Assistant.
I'm trying to do a Master reset on my Catalyst Express 500 (WS-CE500-24TT v01) and I'm having troubles with this. url...I do everything as it says, but when I plug the cable and I pull up the Web browser nothings appear, just the message that I don't have a Internet connection. The LED port on switch don't stop blinking as LED setup either. Is there another way to do the master reset?
View 0 Replies View RelatedI'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
View 4 Replies View RelatedThe last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
I created new VDCs. Since I have done so, there is not switchport command under the interface configuration.
The interesting this is that it is available on the admin VDC, but not the new VDC I created. I cannot create a peer VPC Peer link between my 2 Nexus switches. I did allocate ports to the new VDC and I did verify the enabled feature are the same.
why the switchport command is not available?
I have Catalyst 3750 running IOS version c3750-ipservicesk9-mz.122-55.SE.bin. I have an access port that connects to a Redhat Linux version 5.4 64 bits machine. When I perform a "show mac address-table interface g1/0/3" where the redhat machine is connected to, I see two mac addresses on this access port. One of the mac addresses, 0025.9006.4898, belongs the the redhat machine. the other mac address, I have no idea where it comes from. I tried to perform clear mac address-table dynamic g1/0/3 several times but it does not work either.
View 8 Replies View RelatedI'm unable to apply a policing limit in a switchport of the CISCO861 router. This is my configuration:interface FastEthernet0, service-policy input wired-input,service-policy output wired-output end.
View 3 Replies View RelatedI have encountered a different issue. When I configure " switchport voice vlan 2" under f0/2 connected to ip phone, it does not have any effect.
Below is my set up:
Sw is cisco cat 3524 XL.
ip phone-------f0/2( vlan1)-----SW----f0/1---trunk------f0/0-CME-router+dhcp
|
f0/3( vlan2)
tftp server ( 201.201.201.3)
switch has two vlans:
vlan1 (data) 200.200.200.0/24
vlan 2 (voice) 201.201.201.0/24
Switch management int vlan 1 : 200.200.200.3
router
f0/0.1 200.200.200.1
f0/0.2 201.201.201.1
The trunk is working correctly. (code)
I have a a hardware server running a VM hosting virtual servers which are all on different VLANs. My challenge now is to configure the switchport that the server is connected to, to see all the VLANs needed by this VM. The VM has an IP that is used for managing the server VMs which is on a different VLAN also.
My switch is a 2960 switch and it is presently trunked from the core switch.
I have a Cisco 2901 with the 4port gigabit ethernet switch module that I'm trying to get configured to have a seperate subnet for each port. So far I have it set up so each subnet is a vlan, then on each port I use the switchport access vlan command to tell it which subnet I want that port to be on. However, there is one port that I need to have 2 subnets on. The way I found to do that was to use switchport trunking on that port, but it doesn't seem to be working properly. how they would configure this? Right now I have vlan 101 as x.x.x.17/28 and vlan 103 as x.x.x.53/30. I think where I'm getting hung up is the proper association between the physical port and the vlan subnets.
View 5 Replies View RelatedCurrently have two routers inside our network.
One is the default GW 10.1.1.13
One is Jump Router for ATT 10.1.1.12
Both connected to HP Procurve L2 switch
The ATT Router is 10.1.1.2Want to replace GW and Jump with one 3750 L3 switch.icomplish this with only one port g0/1 connected to HP Procurve?Can I make the switchport 10.1.1.13 and then create a ip vlan999 10.1.1.12?route all to 10.1.1.2Or do I just connect two ports, and hardcode them with an ip?
I'm setting up a new 4900m running cat4500e-ipbase-mz.122-53.SG5.bin. I'm attempting to create Port-Channels as a Trunk for uplink to a 4503 running cat4500-ipbase-mz.122-37.SG1.bin.When I attempt the command "switchport trunk encapsulation dot1q" it errors out.
View 3 Replies View RelatedWas wondering how to set port security on the 881. I have all the FE ports shutdown except one and want to limit that port to one specific MAC address.
View 7 Replies View RelatedOne of my engineers issued a command to turn off port security on a number of ports using the range command. The command failed on the first attempt due to a tacacs auth failure which I suspect is due to a low tacacs timeout value. The engineer then reduced the number of ports in the range command and re-issued the config change after which the switch just crashed and rebooted.
The logging buffer on the switch displays the following:
000072: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: System previously crashed with the following message:
000073: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE3, RELEASE SOFTWARE (fc1)
000074: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Technical Support: [URL]
000075: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Copyright (c) 1986-2009 by Cisco Systems, Inc.
000076: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED: Compiled Wed 22-Jul-09 07:03 by prod_rel_team
000077: *Mar 1 00:03:00 GMT: %PLATFORM-1-CRASHED:
[Code]........
I have done some searching and this could be related to bug CSCsq71492. I have tried using the output interpreter but it is still down.
I have several SF300 switches deployed (SF300-08, SF300-24P). They are connected to IP Telephones (NEC) which communicate with the switch for auto voice VLAN on LLDP. The problem I am experiencing is that periodically the IP telephones are rebooted by the telephone vendor and when they do the switch puts that port into "Locked" port security mode and discards all traffic to the port. The IP telephones of course do not work. In other switch models, I have seen the ability to enable / disable port security switch wide or on a port by port basis. This model does not appear to have this feature. How to disable or why the phones would cause the switch ports to "lock"? There is usually one PC attached to each phone.
View 1 Replies View RelatedI have network consists of more then 20 cisco 2950/2960/3700 switches. I have configured port security in my switches. initially when i configured on my switches it worked fine....even for copule of months it worked fine. but suddenly it start creating issues and now i am not able to implement port security on switches. the configuration is same but there is no effect now. Same switches were fine but now even having same configuration it is not working. please see the configuration: [code]
View 5 Replies View RelatedWe have several 3750 stacks across our campus that we are unable to completely clear port security on. We have mac address stick set up on all access ports. When we clear the sticky address on the port, the mac address is removed from the running config like normal, but we keep getting port-security voilations. If port security is taken off the port completely, i.e. no switchport port-security, traffic still doesn't pass the port. Even clear port security across the stack doesn't work. If we try to reload the stack, only the master reboots, and the other switches in the stack lose switch capabilities.
View 1 Replies View RelatedI've just completed a port security project at a site on numerous Cisco switches and all works well, however they have 2 Nortel 5520 switches (which I left until the end) which they would like to lock down. I have logged a message on the Nortel forums and I have heard nothing for days. I just need to lock 2 ports down to the Mac address of 2 computers stopping any other computer being plugged in.
View 2 Replies View RelatedI'm trying to test port-security in my c3550 but when I show port-security int f0/23 shows it only "Disabled" as below:
run
interface FastEthernet0/23switchport access vlan 200switchport mode dynamic desirableswitchport port-security mac-address stickyspanning-tree portfast
I configured port security on my 2960 switches with the following commands: [code]
The problem is that when I should change someone's PC, first I disable port-secirity, then I clear all the mac addresses learned on the interface, then I plug the new PC and enable port-security. The new PC couldn't connect to the network and it's mac address has not be learned on the interface. Why?Which commands should I use to clear an old mac address and enable port-security with the new mac address.
For many years we've had the following vlan and port security config on our 3560s: [code] This has worked great on 12.2(37)SE1, 12.2(40)SE and 12.2(46)SE. However since 12.2(50)SE, and I've tried all the versions since then, we have a problem with 7900 phones and ATA186s taking upwards of 20 minutes before they can get a valid IP number.The problem on the newer IOSes seems to be related to the inactivity aging.On the older IOS versions the mac address of the voice device appears on the voice vlan straight away.
On the newer IOS versions the mac address of the voice device appears on the DATA vlan and seems to be stuck there until the inactivity aging removes it. It then gets re-learned, sometimes on the voice vlan, and sometimes on the data vlan. If you're unlucky and it gets re-learned on the data vlan you've got to wait until the inactivity time ages the address out again. Repeat until the mac address eventually gets learned on the voice vlan. I don't want to be stuck on 12.2(46)SE forever.
I have connected a 10BaseT device to a CISCO Catalyst 3560xPOE switch with dynamic port security. All seems to work fine when the distance between the two devices is closer then 200ft. When I connect to 10BaseT devices farther out near 300ft the response from the attached device is lost. It works ok on unmanaged switches at the longer distance. Is there a minimum response time from attached devices for dynamic port security to work properly? Is there any other explanation why it would work on cheaper switches, but not on the Port Secured Switch?
View 2 Replies View RelatedI have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE). I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings. Is port-security no available on the switch modules?
View 3 Replies View Relatedour C3750 like the one described here [URL]
We have the port on the switch set like this:
switchport port-security maximum 25
switchport port-security
switchport port-security aging time 2
switchport port-security violation restrict
switchport port-security aging type inactivity
In case a device connected to the port is inactive for more than 2 minues ( aging time ) the first frame/packet the device generates arrives to the port on the switch, but the switch does not forward it to the appropriate port ( discards it or whatever ).
So far I tested on
1 30 WS-C3750E-24PD 15.0(2)SE2 C3750E-IPBASEK9-M
2 30 WS-C3750E-24PD 15.0(2)SE2 C3750E-IPBASEK9-M
3 52 WS-C3750G-48PS 15.0(2)SE2 C3750-IPBASEK9-M
[Code].....
When we remove port security from the port, it works perfectly fine, as expected.
It seems this is not HW or IOS version related. It seems it is not a stack synchronization issue, it does not matter if a device is connected to the first or other stack member. I tested on C3560 too, here there are no problems, so seems it is 3750 related.
I have 2 3560 switches that are running 12.2(25)SEE2. Port security is enabled on some of the ports. Whenever there is a power failure, when power is restored, 1 port on each switch goes to err-disabled. The mac address that causes this is a valid address for that port. Below is the configuration on one of the ports.
View 1 Replies View RelatedMy group has recently started configuring traps on our switches to alert us of issues as they arise vs. waiting for the Helpdesk to receive user complaints and then responding.We have successfully configured the 2950 and 2960 switches to alert us when a port-security violation happens. However, the 3750 switches refuse to fire the port-security violation traps. The 3750's will fire an errdisable trap when the port goes down though.
Here is one of the port configurations:
interface FastEthernet1/0/45
switchport access vlan 5
switchport mode access
switchport port-security
switchport port-security mac-address sticky
[code].....
And here is the output of the port-security debug:
2522070: Oct 21 16:37:04: %LINK-3-UPDOWN: Interface FastEthernet1/0/45, changed state to down
2522089: Oct 21 16:37:05: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa1/0/45, putting Fa1/0/45 in err-disable state
2522100: Oct 21 16:37:05: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0012.3f07.95d3 on port FastEthernet1/0/45.
All of the 3750's are running C3750-IPBASEK9-M, Version 12.2(53) SE2. Wireshark also shows the errdisable traps, but no other traps so I've ruled out the traps being missed. All of the switches have been reloaded and power cycled.
I am looking to simply monitor Port-Security , Error-Disable and HSRP. I would like to receive an email when any of these are triggered.
Port Security - Port Is shut down
Err-Disable - Port goes into err-disable state (securedown)
HSRP - When HSRP standyby changes are detected
I need to receive emails with any of the able are triggered. What is the easiest way to do this? I know SNMP is the main option but I have never worked with SNMP and dont understand it too much.
Equipment:
2x Cisco 1921 series routers
3x Cisco 2960 POE switches stacked
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies View Related