is there a way on a WLC5508 to push the same configuration on multiple APs in 1 shot?I need to change the High Availability settings on most of the APs (not all). And the only solution i find is to do 1 by 1...
View 6 RepliesRegion : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : TD-W8951ND_v5_120522
ISP : N/A
The wireless adapter settings page has an entry for 'PIN' and 'PBC' for WPS.Selecting either always results in the client station requesting the routers pin, indicating that the pushbutton selection is not working properly.The router was doing this with the version of hardware that it was shipped with. i have downgraded to 120522 and the router is behaving exactly the same.Has anyone successfully configured the router for pushbutton connection? do not suggest that we use the pin setting as we have a requirement for dumb devices to connect to wireless and they only support pushbutton connection.
looking at doing the site survey before detailed implementation. we plan to use a wlc5508, AP3602, a good tripod/stand, PoE switch and AirMagnet to conduct the site survey. i'm inclined to use a single AP and just a guest SSID and let AirMagnet merge the readings on where i 'locate' the AP (on 1 VLAN)
View 1 Replies View RelatedUsing LMS 3.1 in win 2003 SP2. Recently experiencing a problem, not able to fetch/push config for the n/w devices. I deleted and re added the device to lms and found able to perform the task. There was no connectvity issue during the problem.
View 6 Replies View RelatedIn one week I need to import the config from my 4404 WLC to my new 5508, then I just want to change the mgnt IP address of the 5508 and then bring it into the same mobility group.How do I import the config when the 5508 is straight out of the box?
View 13 Replies View RelatedI have WLC 5508 with 6.0 software and kept in main office and 10 sites are connected . I created Group and hreap for the sites AP.Now customer wants the secondary WLC to keep on one another site. And the customer is asking all the configuration like ap group and all should come to secondary wlc automatically . In future also if he create any new group in primary it should come in secondary wlc.And if primary goes down the secondary should controll all the sites and when comes up primary should taken care.Active standbye mode.
View 10 Replies View RelatedI have on my desk a WLC-5508 that I need to setup to ship to a remote location. Normally we configure 4402 model and this model/version appears to be much different. I am trying to configure just enough via the command line to access the GUI via a laptop directly connected to the device. I’ve gone through the Wizard Configuration Tool where you set the hostname, admin account, and management interface (among other things). We use LAG and tagged VLAN on the management interface. I’ve been told in the past this is how we configured the 4402 models via laptop directly connected once the GUI is accessible, but with LAG enabled I don’t understand how a laptop could communicate via trunk, so I've disabled LAG and set the VLAN to untagged. In either case the laptop does not communicate with the WLC. Skipping ahead to my current setup I see the following information via the CLI:
(Cisco Controller) show>interface detailed management
Interface Name................................... managementMAC Address...................................... IP Address....................................... 10.1.1.20IP Netmask.......................................
[Code]....
I want to start implementing a small outdoor mesh network of 3 APs Aironet 1550 in order to grow afterward with more APs. Is there any way to configure those 3 APs in an outdoor mesh configuration (for example, only one RAP and two MAPs) without a Wireless LAN Controller or I have to have at least, one WLC? My idea is to have a WLC 5508, but at the very beginning I don't know if my budget is gonna allow me to cost the WLC.
View 7 Replies View Relatedhow i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
I have an asa5520 runing 9.0 that I want to setup for simple NAT, i,e 4.3.2.1/30 on the outside 192.168.1.1/24 on the inside with dynamic NAT outbound. The new IOS has thrown me for a loop.. I have everything working except the NAT. Any SDM screen shot of the Dynamic NAT entry? even if the IP's are different, I can figure it out...
Also, is there a way to make the unused ethernet interfaces gig0/2 and 0/3 into switch ports on the internal net? (or VLAN like you could do on the 5505)?
..how many PCs are allowed to connect to the printer via printer sharing? Is it unlimited?
..the printer are connected to the main PC
printer : Canon Laser Shot LBP-1210
I've got a question concerning the configuration of multiple AP manager interfaces on -for example- a cisco WLC 2504. I've read the configuration guide but I'm not sure whether this is the way the protocol works. Say I want to distribute AP's (and traffic) across various AP Manager interfaces on the WLC. I would configure the following:
Create one management interface (which will automatically also be an AP-Manager interface)Configure 1 (or more) Seperate ap-manager interfaces, assign them to a port number, and select "Enable dynamic AP Management". VLAN ID's will be the same.Create a WLAN and configure it's interface to "management" Is it correct if I state that the LWAPP protocol takes care of the discovery from the Access Point and sends information about the available AP-manager interfaces back to the AP and the AP knows which ap-manager interfaces are available, connecting to the least loaded one?
I am having an issue here. I have 2x 5508 that each have 100 AP license and a little under 200 access points. Basically all of the access points are using DNS to connect to the primary controller that has the DNS entry. Basically half of my access points need to be on the second controller and in order to do this I have been using the high availability mode of each access point to push them to the second controller IP address.It was working perfectly until now. I have pushed 28 access points to the second controller and the last two I need to push at this location just keep resetting on the primary controller. Neither controller is configured as master controller.
View 4 Replies View RelatedI am facing problems of the WPS Push Button on the Linksys WRT610N version 2.0 router which has stopped working. I don't see the Blue LED blinking. The WPS button no more works on the router. It was working before. I did a firmware upgrade. Could this be the cause?
View 4 Replies View Relatedjust to relieve a little those who complain for the loss of functionalities/control caused by the new firmware, I want to let you know that yesterday evening when I came back home the router was bricked. After more than 2 hours of tests with the online support, they ended up the device has to be replaced.To add insult to injury, I ALSO HAVE TO PAY to ship my router to Cisco warehouse. I couldn't believe my eyes... It's not for the 10 bucks it costs the shipment (even if 10 bucks are much better in my wallet than in Cisco's), but I already spent around 300 bucks less than 2 months ago to buy the two devices and now I have to pay to fix something I have not broken.
View 4 Replies View RelatedI have faced configuration of multiple nat/pat problem.Point is when I paste into router another nat pool or nat with route-map or just static nat they doesn't work I mean only one of them works.So, I have several connection hardware cisco 2811 latest ios 15.1
1. internet
2. Local host that must be translated into global local ip addresses be routed
3. vpn local hosts that must be translated into local global addres
Currently we have 20 remote sites, each with 2-5 AP's each. They all connect back to our Main Data Site in the US and register on a single WLC5508.
We do not have a backup WLC, but are looking to purchase one. What I would like to know is, are there any problems with the secondary WLC being installed in our Main Data Site in Europe? These two main sites are connected via a 10M MPLS WAN.
So all the remote sites could still connect to the WLC in the US, but in the event of a WLC failure in the US, they would need to fail over to the site in Europe
I'm using WLC5508 /w 7.0..My client do not get its IP. Status shown "DHCP_REQD".I found in (Cisco Live) Troubleshooting Wireless LANs with Centralized Controllers This related with Enable/Disable DHCP Proxy checkbox. I solved. with Enabling this.But,
1) Why this box have been working correctly for longtime? No one did diable/enable this feature on my box.
2) I guest, ver7.0 Disables this chechbox by default. Or not? I also have others two 7.2 boxes. Those are all Enabled.
I have an SRP541W with two ADSL modems attached to it. Both are running bridged mode with PPPoE connections to two different ISPs, (TPG and Telstra Business Direct). The TPG connection is far cheaper, and has a much higher download limit. Sadly, if I leave the router in "load Balance" mode for the WAN, it "prefers" the Tesltra connection because it's faster. I want downloads for movies/music, Youtube, Internet Radio, etc, to go through the TPG connection. Is it possible to do this in the router, or would I need to set up a proxy server, (or some other external device/application)?
View 5 Replies View RelatedI have a WLC5508 , we are using external DHCP for WLANs
one WLAN is able to get IP from DHCP server but another WLAN not , the DHCP server is same , only 2 different scopes.
This is debug
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP received op BOOTREQUEST (1) (len 308,vlan 1, port 1, encap 0xec03)
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP processing DHCP
[Code].....
I have some problem about dhcp via VMware 7.1. My client connect the wifi and get ip address well, then, i turn on VMware (inside my computer) and set as the bridge mode. I found that my VM cannot get the ip-address from dhcp server and I using WLC5508 version 7.2. I try to connect via Switch, my VM get the ip address well.
View 1 Replies View RelatedA customer have a bad coverage in a corner of his branch office. He like to add a mesh AP (MAP) in the near of that corner.
I checked allready the documention about Mesh but i'm not sure if Flexconnect and Mesh works togheter. This MAP is in a branch office and the WLC is in the head quarter therefore he likes to uses Flexconnect togheter with Mesh.
I have a customer who is going to deploy a WLC HA AP SSO setup. I have recommended them to have 4 Gigabit SFP modules in each WLC5508.The customer now asks if it is possible to only have one or two SFP modules in the standby unit ? As he says it is properly not going to go in service one time within the next five years if he is unlucky.
View 5 Replies View RelatedIs it possible to setup DHCP on the WLC5508? If i have 2 or 3 VLAN with different Scope and IP range, how can i do?
View 1 Replies View RelatedWe have five cisco WLC 5508 and one WCS .The WLC is running on 7.0.116.0 version at present but we want to upgrade it to 7.4.100.0 but on cisco site at download location , the below thing is mentioned...
WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time
Access Point Model----Cisco 3501i Series
So i want to know, can i upgrade it to this version when we are having the WCS in our network ?
I have to configure multiple vlans served with a unique DCHP server . As first step, I just will The DHCP server to serve 2 vlans. The following is the hardware and configuration that I implemented :
[code]...
But If I connect the DHCP server on a trunked switch port and adapt the DHCP server gateway 172.16.0.1 to 172.16.0.254, hosts receive ip address properly.I have to connect the DHCP server directly to the router. How can I do that, what is wrong in the configuration?
I have a WLC5508 and 25 LAP 1041. I use two wifi, one with RADIUS for data and other with wpa-psk for voip. The problem is the voip conectivity is broken.How can i improve the handover?
View 11 Replies View RelatedI have been asked to setup wireless and we have purchased WLC 5508 and 1142 APs.We have several remote sites and a centralized WLC. The requirement are to have a common SSID (Corporate) advertised across all the remote sites and have that SSID locally switched, and have another two SSID Guest and Mobile tunneled back to the central site (WLC).I want all the wireless (Corporate) clients to use the same subnet as the wired clients at each remote site, the IP assigment will be done by a DHCP server at the central site. The Guest and Mobile users will use a common subnet each across all the site and this will also be handled by the DHCP server at the central site.
I have enabled H-REAP with Centralized Authentication and Local switching but I'm not sure about the second part which is to have a common SSID (Corporate) across the remote sites and localy switched whilst having the other two SSIDs tunneled back to the WLC. Cisco TAC told me to configure dynamic interfaces for each of the remote site but then he said I still wouldn't be able to switch the Corporate traffic localy if I use a different subnet to the wired subnet for the wireless clients.
My problem ist that i have 4 air-cap-1552e APs witch are powerde trugh Power Injectors. They worked fine for a few days but then the controller (7.2.111.3) lose connection to them. Right now i have only one Joined AP. The other 3 are status not joined. I can Ping all 4 Aps and wifi clients are connected through them.
View 8 Replies View RelatedI tried to implement WLC5508 in my network but when I came to connect it to the switch core which is a Catalyst 4000 the link didn't get up. This switch module is a fastethernet, I wonder if that might be the problem since I also tried connecting my laptop to the WLC and the link got up.
If that might be the cause, is it possible to get WLC to 100 Mbps?
we have a cisco WLC 5508 on which few SSIDs are configured, and two kinds of APs: AIR-LAP1142N-E-K9 and converted AIR-AP1141N-E-K9.
When in WLAN settings we leave WPA2 policy and AES encryption, iPads2 can connect without any problems to AIR-LAP1142N-E-K9, but there is no connection to converted AIR-AP1141N-E-K9. MacBooks, iPhones are connecting without questions.
When we set WPA2+TKIP everything is cool, but other Apple devices can't rich 802.11n speeds((
With only WPA2+AES or both WPA2+AES+TKIP enabled on a WLAN the WLC gets such messages :
Decrypt errors occurred for client xx:xx:xx:xx:xx:xx using WPA2 key on 802.11b/g interface of AP xx:xx:xx:xx:xx:xx
But I know that it can happen when you offer funny encryption combinations that client doesn't like (wpa1+aes, wpa2+tkip). But the advise to try to only enable wpa2/aes for some reason doesn't work.
how to set up support 802.11n on WLC4404 or WLC5508 in the 2.4Ghz? WLC4404 supports 802.11n? or support this protocol only in the brochures? I spent a few days, but did not get the result. I'm connected at speeds 65/130Mbit, but the real speed tests never exceeded 45Mbit. The AP from the test laptop is 7-10 meters.I tested the laptops with a Linksys AP E1200-EE ( 40Mhz, FastEthernet uplink port...)and received nearly 100Mbit!
At WLC5508 able to connect at speeds 150/300Mbit/c but only in the 5GHz band, but real speed tests never exceeded 70Mbit.In 2.4Ghz range I connected at speeds of 130/144Mbit/c, but actual measurements showed no more than the 45Mbit.
All tested with iperf and with site speedtest.net.
iperf -w64K -s
iperf -w64K -i 2 -t 300 -c x.x.x.x
Laptops: Asus (Atheros AR9002WB-1NG) and Sony (Advanced-N 6230).
My tests AP: 3501I-E and 1252AG-A
SW on WLC5508 7.2.110.0
AP tested in different variants - open system and WPA2+AES.
[code]....
I have two WLC5508 controllers running 7.0.230.0, which having the two of them probably is inconsequential because all the APs are added to only one controller. The problem I'm facing is that I have several LAP1552E's deployed throughout my facility, and I have several that are doing Ethernet bridging to some Cisco switches using G0. In this, I have a PC at the end of one of these switches, and using Iperf and PingPlotter to get some metrics, and what I'm seeing is >400ms latency with <3 Mbit throughput to the PC. On the 802.11a radios I have 18 Mbit set as mandatory, with everything below disabled and everything above Supported, with all MCS indexes under 802.11n enabled.
My channel is set to 161 with a 40 MHz channel-width, and a power of 3 configured.After many days of trying different power settings, channel settings, and such, I can't get better results than above and my channel utilization stays > 75% at all times. I do have video cameras attached to the other bridges switches, and have video QoS set to Bronze and the cameras configured to ~ 1 Mbit bandwidth maximum. Also, average RAP-MAP distance is ~ 1100 ft and average MAP-MAP distance is 400 ft, with the longest RAP-MAP being 1400 ft and MAP-MAP distance being 875 ft.