D-link Dcs-930l :: Router Not Allowing Anyone To Connect Via Wifi
Jul 23, 2011
My internet speeds are 45 Mbps DL and 1 Mbps UL and my various wireless connections (3 laptops in my household) were achieving speeds anywhere from 25-40 Mbps DL. My router started acting up and wasn't letting anyone connect via wifi so I did a factory reset and set it up the same way I did before (as best as I could), it started working fine again but now the speeds on all the devices that are connecting to at are capped at 18 Mbps. A simple speed test shows that no matter what they won't pass 18 Mbps, I am almost 100% certain this is the router and I was wondering what I might have done wrong or what is causing this.
I cannot get the camera to connect to our wifi via WPA2-PSK:AES, which is what it runs. The network /SSID is visible in the setup, but it won't connect and get an ip. I see no error messages or any kind of information at all in the admin web page.I've upgraded to firmware 1.05
I just recently purchased the DCS-930L wireless camera, and I am trying to connect it to my Netgear router but it states that there's an error and can't connect. My itouch and laptop connects fine with the router.
I'm having trouble with one of my DCS-930L cameras. I have successfully installed it and it's connected wirelessly to a Dovado router. However, after some 2 weeks the wireless connection drops and I can't connect to the camera anymore. As the camera is 350 km away I can't restart it. This happens everytime and the last time I was around the camera and indeed the camera LED was green. I restarted it by pulling the powercord and after that the camera worked for som 2-3 weeks and then the same problem again.I have 4 cameras, and it's always the same one that drops the connection and the router is only some 5 meters away from the camera. No walls between the router and the camera. I have the ability to restart the router with an sms, but that doesn't make the camera reconnect.
I'm using a Verizon DSL router, Mac D-Link Camera Setup Utility (BETA), and Mac OS X 10.6.7. Configuration of camera is as recommended in manual with CAT-5 cable. Green light blinks irregularly in a communicating-with-router manner. The setup utility won't recognize the camera
I downloaded the MAC setup Utility(BETA) and it can't find the camera.The camera is connected via Ethernet-Light on the front under the lens is green (blinks sometimes)First thing I noticed wrong was the setup utility asks if the light on the side of the camera is lit green-there's no light on the side of the camera as far as I can tell. I tried unplugging the camera and hitting the reset button on the back-nothing works.
I have installed two 930L cameras which work fine via mydlink. When I attempt to connect them to D-View Cam 3.11 they fail to connect or will not stay connected.I first tried connecting to the router with both cameras in the same room as the router. One will connect and stay connected but the other will connect and freeze or not connect at all. If I move th GOOD camera out of the room, it will not connect.Do I have a router issue? I am using Verizon FIOS with their supplied router (Actiontec, I think). My wireless laptop connects but signal strength is never 5 bars.
I'm getting an error during setup that says "You are unable to connect to the mydlink web site, and your camera could not be added to your mydlink account."
I have a DI-604 Version E3 D Link router and I'm trying to allow VPN through the router but I'm not exactly sure how. I have the VPN set up through my PC's but I need to configure the router aswell. Trying to set up the VPN so multiple locations can access it,
I just bought the 655, mainly for school/Xbox. My parents use it also, but I bought it for myself mainly (shh). I set it up correctly and got connected, but suddenly I wasn't allowed Internet access. The router connects to my laptop, but won't get Internet access. I called customer service and he didn't know what to do. We tried everything he knew and nothing worked. I don't want to return the router cause I read it was very good, but I need internet for school. I have Rev. A and F/W 2.00.
Since the blackout beginning of this week from dlink I had to reset my camera totally to operate it again. works now again with iphone and with mydlink. But it only works as long it is connected via lan cable to my router. I accessed the set up (via ipaddress) and entered the router details to the setup but as soon I disconnect from lan it does not work anymore. What did I oversee.
I have a wireless network in my home. I reliably get solid connections on our various devices such as the Wii (netflix streaming), a net book, a laptop and Wi-Fi connections on android phones. When I first set up the 930L I thought it was defective because I couldn't get a connection. Until I did it in the same room as the router okay, that worked. But I move 2 rooms over and I no longer connect.
Seriously, I can go a few rooms away and easily stream an HD movie via netflix to my net book. But if I set up the 930L at the exact same location it will not connect. If I move the camera within about 20 feet of the router with only maybe 1 wall between them, it will connect.
At this level of wireless power it is nearly worthless for me. Is my camera defective or are all of them this lower powered?I am running a dlink router, 300N, WPA security. Like I said, I can connect if I'm literally 10 feet away. But any significant distance or anything more than a single wall in between and the router no longer sees the camera. And all other wireless devices have strong, reliable connections all through my house.
Just replaced my SMC Gateway with a Cisco Home Networking Modem, router doesn't see DCS 930 cameras. Working perfect before. I start the wizard, I plug in camera power, plug in ethernet cable for setup, light is green as requested, searches for camera, comes up "No Cameras found". Called ISP provider to reset modem, still no go. Tried a wireless setup using the "buttons", no go. Reset cameras..
I have the DCS-930L camera. I need to know how to setup port forwarding/triggering on my router, which is a Cisco DDR2200 CL. I understand that in order to use the camera, i need to do this. how to set up NAT.
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
I'm trying to connect the D-Link 930L Wireless N Camera to my E4200 router. When I have the camera connected via the Ethernet cable it works fine, as soon as I unplug the Ethernet cable it will not connect wirelessly. I tested the camera on a friends router E3000 and the camera connects fine and work flawlessly on his network wirelessly. Any settings in the router that need to changed or set differently?? All of my other devices work great. I have been through D-Links Tech support all things point back to my router.
EA4500 Linksys router stopped allowing vizio Internet apps to connect from two different TV's. Problem, Just got brand new EA4500 router and Motorola SURFboard DOCSIS 3.0 High-Speed Cable Modem Model: 575319-019. I have 2 new vizio big screen tv's with internet apps. All was working fine and had no problems but occasional drops or limited access.
One day BOTH TV's could no longer connect. However, The tv's will connect to another access point. therefore the problem does not exist in the TV/s and has to be a problem in my access point (I.E. Router allowing access). Additionally, all other devices connect and work fine. I have already unplugged everything for an extended period of time. Checked for updates on firmware and verified no software needed to be updated. Rebooted router... Am using wpa-psk and feel i shouldn't have to go weep as it was working fine...
I have a TP-Link TL-WN723 USB WiFi adapter attached to my laptop, which runs WinXP Service Pack 3. It successfully detdcts the WiFi provided by my Edimax BR62-04Wg router, but when I try to connect, it cannot obtain an IP address and cannot connect to the network.
- The very same WiFi adapter can connect to other routers without any problem - Any other device can connect to the very same network provided by my router without any problem - Using the WiFi adapter with other computers does not work
Thus, it seems that the problem is somewhere between this specific router and WiFi adapter. Here is an interesting detail though:If I try connecting to my WiFi while a LAN cable from the router is plugged into my computer, the wireless connection establishes too. Even if I later unplug the LAN cable, the wireless connection continues to work. But it won't establish the connection without the cable plugged in.Here's what I've already know/tried:
- Rebooting the PC - Re-installing the WiFi adapter's drivers - All drivers and firmwares are the newest available - Re-starting and reconfiguring the router - Using the Windows client for wireless networking and the client included on the WiFi adapter's CD - Changing the router's connection type to any available option: Access Point, Station Ad-hoc, AP Bridge WDS
None of these had any effect except for one:
- When I changed the router's connection type to Station Ad-hoc, I could connect wirelessly even without the LAN cable plugged in, and I had Internet access. However, in this case, other devices, such as smartphones could not detect the WiFi connection.
i was playing back the recording,when i skipped ahead, the sound disappeared. I am recording 10 hours worth everyday, most of the time i just need to skip to a certain time to see and hear what was going on,
How to add an external antenna? I'd like to mount a DCS-930L in a location (inside a metal housing) that would need the antenna to be a few inches away. Any internal layout information?
I just brought this D-Link DCS-930L. I insert the disc and follow the instruction and select the option of without WPS and follow the step of connecting the lan cable and power point but at Step 2, after the green light, it keep prompting me that it can't find the camera. it connected to the router where there is a lan cable connected to my pc.
I had to get a new router from verizon cause the old one died. so i reset the camera and wipe all the dlink software and settings. I then start fresh. i get all the way to choosing wireless and input the password. It states that there is a problem saving your settings. I tells me nothing more. I spent 4 hours on the phone with tech support and i can get it working through wired but I can't put it in my childs room wired. it worked perfectly before the router switch. funny thing is that its the same brand and model router.
i installed cameras but want to set up for motion. I have 2 dcs 930l cameras and I can see them live i have only 2 settings live video and camera info i also downloaded the link from support.dlink.com i have a new windows 7 laptop and it keeps tryng to download java app problem is now computer keeps asking for a username and password and I have no idea what username and pw it wants as it says in the box it is unsecure
Is it possible to install the D Viewcam software on a PC that is offsite (different network) as the camera and record from there? Basically the camera is home and you record from work.Can I record directly to any NAS (same network as camera) without having a PC in the middle? Or do I need a specific NAS?What about one of those external hard drives that hook up directly to a router?
I have the DCS-930L set up at home with motion detection emails. I only want it to be sending emails when I am not home, of course, but there's no way to turn off the camera through my dlink.com as far as I can tell (only an option to remove the camera, which I assume is something more drastic). Is my only choice to unplug the camera when I don't want it emailing?
I am able to access 930L (2 cams) from wifi be it laptop,iphone or ipad but I am not able to see it through 3g.I have Huawei fibre optics broadband reuter from Starhub.Starhub is running away if ask them to fix it. Huawei never takes the call.I tried atleast 3 times 10 minutes each at 8006011450.It goes to disconnect. The lot talked about UPNP is enable in reuter but it does not work.
Now i talked to Dlink support with ticket DCX36811.They advised to load the firmware.I did it still the connection timeout is there. we have baby to monitor through iphone/android 3g.
I bought and hooked up my DCS-930L camera last week. Have since traveled overseas and go to Mydlink website, log-in and then it tries to install a java applet that never does install. It shows the security box where it asks me to run and then it shows another security box with a message: java.io.FileNotFoundException:C:usersmynameAppDataLocalLowSunJavaDeploymentsecurity rusted.certs(Access is denied)
I click ok and the java applet never loads. It just keeps saying Installing Java Applet.
I have a DCS-930 running successfully on my home network. Now I want to set up a DCS-932 on a different network at my mother's house in another city, so I can monitor her house from a distance. Questions:
1. After installing, will I be able to see both cameras at mydlink.com if they are on different networks? 2. Is installation any different because there are 2 networks? 3. Can I use the existing install wizard on the laptop that I used with the 1st installation or should I use my mother's PC? 4. How do I get started since the first instruction is to insert and use the CD that came with the new camera?
Basically I want to know what the install procedure is if I am using a different network but the same laptop I used with the 1st one. The laptop has a wireless connection to both networks.
Connected our Brother MFC-8820D printer/scanner/fax directly to one of the 4 Ethernet ports on the back of the DIR-655 in our new install with this router, and all computers can print to it, whether connected via an Ethernet cable or via wireless, but none of the printers can scan. We just get an error message. Scanner driver is installed on all computers. Same printer worked fine via Ethernet on a Windows small business server for printing and scanning. Windows server no longer used or connected. Only DIR-655 as we are dumbing down and getting rid of our Windows server and have gone to a NAS solution connected to the DIR-655.
What can we do to make the scanning work on our Multifunction printer?
In my device I am able to browse through & connect to my HOME wifi network ; But after connecting it says 'No Internet Access'.I tried connecting with my SONY Bluray , iphone , ipad , laptops -- everywhere same story.I am able to plug in the ethernet cable directly from modem & able to connect to network.I am not able to open the http://192.168.0.1 -- ( When I am plugged in the modem directly)
Following are my router details
FCCID - KA2DIR601A1 IC : 4216A-IR601 H/W Ver:A1 F.W Ver:1.00 NA
I think I did everything per the manual, but I cannot access my camera over the internet thru [URL] website. It says that I have to check if I have enough bandwidth, or checked if my camera is not blocked by my router But I have a Dlink DIR 655 router where I have configured the Virtual server (port 80) as it is explain in the manual I also have a DHCP reservation that works fine (I can access the camera within my network) What should I do more now to finally access my camera from internet (this is for me the interest of havinf a network camera!)
