Cisco Routers :: RV180 / PPTP VPN Or IPSEC For Android And IPAD?
Jan 28, 2013
Being new to the RV180 (and VPN routers for that matter) I have been struggling to get a VPN going, supporting both my Android and iPad devices. However, I understand a IPSEC connection would be a more secure sollution. Unfortunatly I cannot find a clear instruction anywhere to do this.I found the settings/descriptions in the RV180 quite different from the (few) settings in the mobile platforms. So far no success in getting it setup.
View 2 Replies
ADVERTISEMENT
Oct 29, 2012
I currently have an RV180 in a small business set-up and curently being accessed remotely by laptops (Quick VPN) and Ipads/Android ICS tablets (PPTP). All is working well but I've become concerned about the security risks of PPTP and would like to shift the tablets to IPSec.
1) For a small business are the PPTP risks real?
2) What are the alternatives for Android ICS? I can't find a Quick VPN client for Android, has anyone seen one.
3) I can't get the core IPSec VPN in Android to connect to the RV180? Is this possible? Has anyone succeeded?
View 0 Replies
View Related
Oct 30, 2012
I currently have an RV180 in a small business set-up and curently being accessed remotely by laptops (Quick VPN) and Ipads/Android ICS tablets (PPTP). All is working well but I've become concerned about the security risks of PPTP and would like to shift the tablets to IPSec.
1) For a small business are the PPTP risks real?
2) What are the alternatives for Android ICS? I can't find a Quick VPN client for Android.
3) I can't get the core IPSec VPN in Android to connect to the RV180? Is this possible?
View 1 Replies
View Related
Oct 29, 2012
For the past week, I have tried to setup the PPTP VPN server on the RV180. The setup was straight forward, but I could not log-on no matter what I tried. I decided to call Cisco small business support, and as I was talking to the engineer, it mysteriously started to work. I was puzzled and somewhat embarrassed because I'd hate to admit it was an id10t problem on my part. As I tried a few different configurations, I began to realize there might be a limitation in the RV180 PPTP VPN server with the current firmware (1.0.1.9).
In short, the RV180 PPTP only works with 192.168.xxx.xxx/24 subnet. My setup has 3 vlans: vlan1 in 172.xxx.xxx.xxx/24 subnet, vlan2 192.168.0.xxx/24, and vlan3 10.xxx.xxx.xxx/24. My originally plan was to keep vlan3 isolated by disabling inter-vlan routing, but I needed a way to manage a couple of devices on vlan3 remotely, thus I wanted to setup a VPN in the 10.xxx.xxx.xxx/24 subnet. This turned out to be the reason why it never worked before. Today when I called Cisco support, I assigned the PPTP VPN server a 192.168.0.xxx ip range, and it worked. Later, I tried assigning 172.xxx or 10.xxx ip addresses to the PPTP VPN server, and they both failed to work. I created another test vlan4 with 192.168.2.xxx/24 subnet, and assigned the PPTP VPN server to that vlan, and it worked again.
I'd like to mention that I already configured the 10.xxx.xxx.xxx/24 subnet with a few devices before I replaced my router with RV180, and I don't want to have to change and test the setup of all the devices. Another reason I want to have my VPN server outside the 192.168.xxx.xxx range is that it's way too commonly used by wifi hotspots that it increases the chance of wifi and vpn in the same subnet.
I can test a few more configurations, but I think the results will be the same. Perhaps Cisco should test the RV180 in the lab to confirm what I found.
View 2 Replies
View Related
Jul 31, 2012
Is there a way to configure RV180 to allow PPTP clients to route Internet traffic via its own internet connection?
I.e. supporting these client options: "Send all traffic" (Mac/iOS), "Use default gateway on remote network" (Windows).
View 1 Replies
View Related
Mar 8, 2013
I have tried to make a VPN connection between RV180W and iPad with PPTP. I have enabled the server, set the address range, added and user and enabled it.
I entered the same information into iPad but when I try to start the VPN, iPad just tried to make connection and finally fails with an error stating that PPP server cannot be reached.
I think the devices are able to make some kind of connection as if I change the gateway IP address incorrect, I get a different kind of error message. I also tried to reboot the router...
View 4 Replies
View Related
Jan 31, 2012
My use case is very simple I want to connect iPhone/iPad using pptp to my home network. I purchased the 180W and looks like I am not able to connect mobile devices to it. My Setup is simple I have ST536v6 (firmware 7.4.4) modem in bridge mode and Cisco RV 180W connect to my ISP using Ppoe. I followed the Admin guide and created the pptp user. If I connect from internal network it connects but when I try to connect the device from WAN it just does not work.
Cisco RV 180W
Firmware Version:1.0.1.9
View 7 Replies
View Related
May 22, 2012
Does RV180 router support client VPN connections using regular Cisco VPN client? Datasheet says it works with Quick VPN client.
If regular non-Quick client is not supported, can both clients coexist (= be installed simultaneously) on the same PC?
Does Quick VPN client support split tunneling?
View 2 Replies
View Related
Apr 26, 2013
Any news on a new firmware for the RV180? I have the most recent version but it still has lots of bugs. IPSec needs polishing. In addition the Logging functions don't work well. I can't send to a syslog and when I try to email the logs I get a email saying there is no data even though several pages of enteries are visible in the web GUI. I've checked the profiles and they are correct. I even tried using just the 'default' profile but no luck.
View 2 Replies
View Related
Mar 14, 2013
I'm using two RV180 for a site to site ipsec vpn. The IPSEC VPN connection is working only if I try a manual connect. After some time connection is droped and no auto reconect for it.
View 6 Replies
View Related
May 16, 2012
I used to have a Netgear Prosafe 318 conncted to a Netgear Prosafe 336G in a small office environment across the WAN between two offices, IPsec preshared key. The 318 took a dive so I decided to upgrade to a new Cisco RV180 VPN router. I set up the VPN access rules exactly the same and forklift upgraded the Prosafe 318 (same IP, same rules, same pre-shared key, IKE setup etc) and the VPN tunnel comes up fine. However, even though the VPN tunnel says connected and I have no problems pinging anything across IPsec between subnets I cannot seem to connect to anything from the cisco side.
From the Netgear side I can connect to anything on the cisco subnet (192.168.0.1 / 255.255.255.0) but from the cisco side anything I try and connect to on the netgear side (172.16.0.1 / 255.255.255.128) times out.Encryption AES-128 (although also tried 3des), Sha-1 SA-lifetime is 3600 seconds, PFS key group enabled DH-group2 (although also tried group1)IKE policy direction Both, identifier FQDN (both sides), Preshared key SA-lifetime 28800 seconds. Firmware is updated on both the netgear and the RV180 to latest version (1.0.0.30 on RV180).Like I said from Netgear to Cisco through VPN tunnel everything works fine from Cisco to Netgear everything times out.
View 1 Replies
View Related
Nov 7, 2012
I picked up this RV180 router because it has one of the fastest thru speeds of all the routers tested that I viewed on smallnetbuilder. That and it has the cisco name. I grew tired of purchasing wireless home routers every year after they fail. So far the thing is nice with one exception.
I have one device that is essential on my network called an airave. It is a small device similar to a wireless access point that works on springs voice network. The thing essentially makes a small cell tower inside your house and connects to the sprint network through an Ipsec vpn. I have not ability to change ipsec settings on the device on my end. The device works fine connected to the cable modem or to the old slow dlink. When I first connect the thing it works fine for about 5-10 minutes on the cisco. Then the thing loses connection and I lose my cell phone service. Just to test any port conflicts I made this the the DMZ with no luck.
I have also tried a firmware upgrade. I have not messed with any of the firewall settings or port forwarding since DMZ should in theory fix that. I have assigned the thing a fixed IP address but that does not seem to make a difference. It did not on my old router and is mostly just for my sanity and to facilitate the DMZ.
View 4 Replies
View Related
Sep 15, 2011
I have an I pad 1, a Linksys RV042 At My Office. And a Cisco RV042 at my Home
However I'm Creating PPTP Connection on my I pad For Both VPN , Office is Connection, but Home is not Connecting. I tried to connect to Home Thru any PC, And It is Working. Any Issues With I pad and Cisco Firmwares and Software?
View 1 Replies
View Related
Oct 22, 2012
How do I fix the problem". Domain not set.invalid may not be the problem. had a power surge at my house and it took down my internet. I had to reset my router back to factory settings and I finally got the router to work with my PC. But I cannot access the internet from my iPad 2 or my Android phone. Both devices see the network and can hook up to the network but the internet is not working on either device.
View 14 Replies
View Related
Dec 12, 2012
TiVo and Pioneer offer remote control software for iOS and Android equipment. I've been using both for a while, and it's great stuff. When hardwired to the router. Behind the DAP-1522, not so much.The DAP works like a champ in every respect except in this application. Everything attached to it can hit the internet- the TiVo, the Samsung smart TV, my laptop via 1000baseT, and to anything else networked in the house. Presently the iPad can control the Tivo, but not the Pioneer. But Airplay on the iPad connects to the Pioneer with no problem. And then the iPad remote can control the Pioneer again.Another example is that the iPad can't find the TiVo, but my Android phone can. Usually.
View 1 Replies
View Related
Dec 29, 2012
Any good vpn config for a router to allow vpn connections from Android phones using L2TP-IPSEC? Router is an 1841 running most current IOS ver 15.1.
View 1 Replies
View Related
Sep 30, 2011
The company I work for uses a Cisco ASA 5510 router. We currently have an IPsec VPN set up and useres connect through the Ciso VPN client using group authentication, then they are prompted for a username and password, and use the same username/password they log on to thier work computers with. Some of the users have recently got Samsung Galaxy 10.1 tablets and would like to connect to the VPN using those tablets, but I can't figure out how to get the tablets to work. I've tried the anyconnect app for the andriod market as well as creating a VPN connection from the Tablet's settings page, but no luck either way. Perhaps I'm not entering a setting right? Has any one had any luck getting andriod tablets to connect to a Cisoc VPN?
View 1 Replies
View Related
Jan 25, 2011
We have ASA 5520 running 8.2(3) software and we're trying to make Remote Access VPN (l2tp/ipsec) working from Android. We succeeded in making IPSEC tunnel (ending "Phase 2 completed"), but we cannot make L2TP tunnel working.We're using RADIUS for L2TP authentication, but ASA doesn't even try to check credentials entered by use. The same set of credentials entered on Windows {XP, VISTA, 7, Mobile} works ok. Which debugging options should we turned on?
View 3 Replies
View Related
Mar 2, 2012
Got some issues when setting up IPSEC/VPN on the asa 5505. I want to connect from the ipad with the built in IPSec client..Get errors when i run the debug crypto isakmp
View 1 Replies
View Related
Jan 27, 2013
Got some issues when setting up IPSEC/VPN on the asa 5505. I want to connect from the ipad with the built in IPSec client..Get these errors when i run the debug crypto isakmp.
View 6 Replies
View Related
Apr 6, 2013
I really worked hard not to write this question here but here I am. I am trying to route all traffic through vpn but I cant browse the web. It seems no traffic goes through the vpn tunnel. Split tunneling works but it doesnt route the traffic through vpn tunnel. I have a cisco asa5505 with base license,
When I try to browse the web with one of the clients I see lots of
6Apr 07 201309:40:5510.10.50.136088410.10.10.153Built inbound UDP connection 834 for outside:10.10.50.13/60884 (10.10.50.13/60884) to outside:10.10.10.1/53 (10.10.10.1/53) (xxxx
messages but at the end I see " Safari could not open the page because the server stopped responding" message or smth similar.
My setup is
Vpn Clients ====== asa5505 ========== CiscoLinksysEA4500 Router ======== ISPProvidedFiberConverterDevice(huawei)
10.10.30.10-10.10.30.50 10.10.10.2(outside int) 10.10.10.1(inside) PPOE(outside)
[Code].....
View 1 Replies
View Related
Jul 9, 2012
I had IPAD setup IPSEC Remote Access VPN to try to conect to ASA5540 and Cat65 VPN service module(V1).I works fine on Cat65 VPN service module using IPAD client, but it is fail on IPAD client connect to ASA5540.THe message should be "VPN server is no response".My laptop Cisco VPN client(Windows 7) works fine on both (Cat65 VPN module and ASA5540).There is any special setting for IPAD client on ASA5540 ? The IPAD ios version 5.1.1.The ASA5540 version 8.4(4)1 ADSM 6.4(9) The Cat65 version is quit old binding with CatOS V12.2 etc.
View 2 Replies
View Related
Nov 28, 2012
I have a situation where the site-to-site tunnel is already established using PPTP IPSec VPN with non Cisco Gateways terminating the link on each end. These non Cisco Gateways do not support L2TP tunneling, and there is no plan to change them.Beyond the Gateways on both ends, we have a Cisco 4500 series switch. We need to forward the 802.1q tagged VLANs between the two sites. Is it possible to use 802.1Q tunneling in this case, going via a PPTP tunnel ?
Cisco's setup uses dot1q-tunnel over a L2protocol-tunnel to preserve the original client VLAN tagging, so does this mean that the only option we have is to setup a L2TP tunnel at the Cisco device endpoints, and have that tunnel go through the existing PPTP tunnel (established between the 2 non Cisco VPN Gateways) ?
View 1 Replies
View Related
May 15, 2006
Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
View 5 Replies
View Related
Apr 29, 2013
I tried any type of combination and just couldn't make it works. Only PPTP works well. Whether Apple iOS IPSec VPN is supported or not?
View 11 Replies
View Related
Jul 19, 2012
I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies
View Related
Mar 23, 2012
I recently installed a new 220W with the sole intention of setting up the PPTP server. I got the router installed and working but cannot get the PPTP server working. Also when i configure a block of IP address from my lan for the server it tells me i cannot use that subnet? i have set it up this way with other routers ( RV042 ) with no issues.
firmware is 1.0.0.26
View 3 Replies
View Related
Jan 26, 2012
I have a pptp server on my network and am trying to configure my new RV110W so that I can tunnel through to it from outside.
I believe I must do port forwarding for TCP on port 1723 to get those packets going to my PPTP server. PPTP also uses GRE and I don't see that as an option anyware in port forwarding... Does that just work... as a matter of the VPN pass through checkbox being enabled ?
My netgear router would lock up every few days but it under the firewall configuration it had list of services that included PPTP and I just selected that, entered the IP addresses on the outside that I would accept, and the IP address on the inside that the PPTP clients would connect to, and it worked....
I'm thinking it is harder on this device because this device supports actually logging into it.. I am interested in learning more about that technique especially if it is more secure but the way I see it the firewall device can see all of my network and the pptp server I am using is on a file server and limited to those files shared on that server.
View 3 Replies
View Related
Aug 8, 2012
I Have RV220W Rev 1.0.3.5/I want to create 5 users adn connect remotely to the office network using a PPTP connection.
I have enabled the PPTP server and created users.From a remote location (WAN) on Windows 7, I have created a PPTP connection and I can connect however I can not ping or map to the office network.
View 13 Replies
View Related
Sep 21, 2012
My network to use a RV042 router. It is connected to my cable modem and working well. I may add a DSL connection later in the month as a backup. All I really want to do now is setup my PPTP VPN connection. I have not been able to find a guide so I will assume it isn't that bad. I set up 2 accounts in the VPN-PPTP Server screen. Built my connection on my android phone and voila nothing works. So I tried to disable the "Block WAN requests". I tried port forwarding the VPN to 192.168.1.1 (address of the router) and no luck. AT this point I am stuck. I know my infrastructure is right because from outside the network I can [URL] and see my router configuration. Now if I could just get a simple PPTP connection
View 7 Replies
View Related
Apr 2, 2012
I need a name resolution within my pptp users. How do I configure the dns settings of a pptp user client.
View 4 Replies
View Related
Dec 23, 2012
Is there any way to manage the RV180 from the WAN side via https and/or ssh?Also, is ssh from LAN even available?
View 3 Replies
View Related
Oct 18, 2012
I have an RV180 VPN router.I try to enable the VPN users with PPTP or QuickVPN but is not working.For PPTP sometimes my windows 7 connects to the router, sometimes doesn't connect with a random error message.When it connects, the windows 7 from outside the lan can see the computers from inside the lan but the computers from inside the lan cannot see the windows7 one. This is random also. When i succed to connect, from that computer, the internet is not working anymore.I tried to set the VPN in the same subnet as lan, i tried with different subnet. Is not working.I updated the last firmware. The same.Restore factory settings couple of times, the same.
View 6 Replies
View Related
