Cisco Routers :: RV 180W - Application Connecting To Apple TV Using Wireless Network?
Feb 8, 2013
i have issue for Remote App to connect to the Apple TV using the Wireless network setup in my 180W.My wired Mac is able to connect to wireless connected Apple TV but my i phone (4, 4S and i Pad) are not able to connect to apple TV.
Do I have to enable some setting for this to work. It used to work in my very old Buffalo router with tomato firmware.
If I connect the Apple TV to wired network it works fine. Instantly it shows up in i Phone Remote app, but not if its on wireless network.
My use case is very simple I want to connect iPhone/iPad using pptp to my home network. I purchased the 180W and looks like I am not able to connect mobile devices to it. My Setup is simple I have ST536v6 (firmware 7.4.4) modem in bridge mode and Cisco RV 180W connect to my ISP using Ppoe. I followed the Admin guide and created the pptp user. If I connect from internal network it connects but when I try to connect the device from WAN it just does not work.
I've got an Apple TV 2, and I currently connect it (wired, that standard being the future of wireless) to one of two routers:
1) my normal router (for UK Netflix);
2) my DD-WRT router with my VPN details (for US Netflix).
Currently, I switch between the two manually, by unplugging one cable and plugging in another. This is fine, but what I'd really like is a way to do this without constantly having to kneel down on the floor and fiddle with the increasingly Medusan tangle of cables I have somehow amassed (they breed, you know).As such, my question is: is there a cable/device that can do this for me? I envisage some sort of box with a hard switch that I could flick to change the connection from one router to another. I have scoured the Internet, but don't seem to be able to find one.
I like to use "URL Blocking" with keywords in the firewall properties. When I activate this feauture, I get errors from the router certificate when I browsing to any site in the Internet. Is there a way to manage this problem without using a public certificate?
I am having issues figuring out how i can make AppleTV,Airprint, Airplay, etc show up on Ipads that are connected to the wireless network. The controller is at a main site which is seperated by 2800 series routers at the remote sites over 100Mbs links. Ipads connect and tunnell back to the main site. I've tried enabling FlexConnect but the devices still get the main site's addressing so i'm guessing they are still tunneling unless the AP loses connectivity to the controller. I have two SSIDs (staff and students). I have tested with just setting the staff to FlexConnect. Do I need to set both SSIDs to FlexConnect to make them dump data locally? AppleTVs are connected wired to the local networks and get addressing associated with that building.
A customer of ours has the following access points and wireless lan controllers on site. They want to use the Apple Bonjour service with Apple TV's and iPads. I have enabled multicast feature of the 5508 globally and one the SSID.The Apple TV has an ethernet connection and the iPads connect over the wifi. The Apple tv is on the same subnet as the iPad's - the Bonjour features do work for approx 5/10 minutes then it stops working for some reason. The Access Points plug into a Cisco 2960 Layer 2 switch, the 5508 controllers plug are in LAG mode and plug into a Nortel Layer 3 stack which I have enabled IGMP snooping.I've read that the Apple Bonjour service isnt designed to work on a multi subnet network - but both the Apple TV and iPad are connected on the same subnet. Sounds like some kind of timeout but not too sure.
how to setup the wireless interface to forward multicast packets? Basically I cant get the ipads etc.. to see the AppleTV to control it. I connected an AP and it works fine so its got to be something with the way the router handles the packets from teh integrated wireless interface. I've been searching the forum for about 1hr and haven't founf anything other than a breif mention of broadcast forwarding and multicast setup.
I am trying to connect to a D-Link DIR655 using a Apple G4 PowerBook equipped with an Apple Original Airport Card (802.11b) to detect WIFi signals. Trying to connect to an unsecured signal at a local Library, the computer states that there is an error connecting to the network. The Library IT checked the settings on the router and it strates the 802.11b is enabled, still there is no connection. Is there a complatibility issue witth the Orinal Airport card and the D-Link Router?
I received Apple TV and a Kobo E-Reader over the holidays, and when I try to connect them to my wireless network, they fail in connecting; even with entering the correct password. Is there something that I need to do in terms of updating, being it should connect having the correct password.
I am trying to connect my laptop running windows 7 to an airport express so I can stream music to my hi-fi.I've tried a number of different things, none of which have been successful.I've tried resetting the device before each attempt to connect it and I've also ensured that the driver for my computer's Wi-Fi (Intel (R) Wi-Fi link 5100 AGN) and the firmware for my router (Linksys E2000) are up to date. The apple airport utility program is also up to date. I also saw this webpage:Sharing my Win 7 PC with Apple Airport Extreme and wireless network. - Microsoft Answers And, all these settings were correct already.I also took the device back to the shop where it was tested and found to be working correctly.
Just plugging in my airport express - Opening the airport utility program, my airport express is recognized straight away. It is highlighted in the left-hand pane and I click on continue. I then get a message asking if I want to switch networks and it says that this is required in order to set it up. I click OK to continue. After a window appears saying that it is detecting apple wireless devices, I get error message number 4 saying that an error occurred while trying to access the network. It then asks me to check to make sure my network is valid.Using ‘configure other under the file tab - The airport express is still recognized in the left-hand pane but I click on configure other. A window appears asking for the I.P. address and a password. I enter the default I.P. address (10.0.1.1) and the default password (public) for the airport express. I then get error 6753 (an error occurred while trying to access the apple wireless device. Make sure your network connection is valid and try again)however, my computer still recognizes the airport express in the list of available wireless networks. I therefore click on it and connect to it. I then try to enter the details (under configure other again). I then get through to the configure apple wireless device screen in which I can input the details of my network details, etc. I enter the details and make sure that they match my routers settings (I have even tried this with no security settings on my router). I then click on update. The computer automatically reverts back to my network and it seems like everything is working. The green light even appears on my airport express. However, I then get a message stating: Airport utility was unable to find your wireless Airport device after restarting.Switching off the wireless network and connecting the Airport express to the computer with an Ethernet cable - The device is also recognized here and I can enter all the details. Before updating I turn on my wireless network so it can make a connection. The green light shows on the airport express but i again get the message that: Airport utility was unable to find your wireless Airport device after restarting.
I am on the Verizon wireless router connected to my laptop and the xbox wired to laptop. I have another wireless router that i want to connect because the main router is in the basement I am on the second floor. How do I connect the xbox to the 2nd router wired?
Does my Belkin F5D8236-4 ver. 1 (firmware 1.00.02) router support Apple's Bonjour print application. I can't get my iPhone or iPad to recognize my new HP Photosmart 7520 wireless printer which is connected to my network through my router.
my goal is to share my cable modem signal over my two story house using two wireless routers. The delima is that the routers don't support wireless bridging and if they did, the signal is too weak to make it worth while.
The remedy I came up with... buy a pair of powerline network adapters and connect one router to the other so I could have a good signal upstairs and then a good signal downstairs.
Downstairs, I have the cable modem connected to the Linksys WRT54G router, which has a line out to my blu ray player, wirelessly feeds a PC downstairs and then has a cable run to the powerline adapter.
Upstairs, I have a cat5 connecting the powerline adapter (which was tested and works with laptop) to the data input port on my second wireless router, the netgear wndr3400.
I can't get the netgear upstairs to pull an IP address from the linksys router downstairs over the powerline network.
I have recently deployed a wireless network using a WLC 2504 with 21 Light APs. All seems fine except that Apple Devices drop their connections every 15 minutes or so. A couple of minutes later they can reconnect but obviously something is wrong.
I've got 3 WLC 4402 controllers and the wireless is working perfectly except for 1 issue. We are trying to connect an apple tv, so we can stream picture, videos etc from ipads and Macbooks to a large display for media teaching.The setup works at home, but not at work.The apple TV is on the same network as the wireless apple devices, (we use a 10.6.4.x-10.6.5.254 range), both are dhcping the addresses (have tried fixing but that made no difference). I've enabled multicasting and igmp snooping and set the multicast address as 239.0.0.0 and it still doesn't work.
I am beginning to get many emails from users who have recently upgraded to OS6 and saying now they cannot connect to our open access wireless network. We use a separate server that users must agree to a user agreement page and they say they get it, but after agreeing, it goes blank and they cannot connect. I am using mostly Cisco 3502's with the 5508 controller using 7.0.112.0 IOS version. Nobody in our IT department has yet to test OS6 yet.
I am setting up a new Guest network with a captive portal and it seems to all work fine except when Apple devices go to sleep. When they come back on it isn't just a case of logging in again as it just indicates to the client that it is still connected and won't present the login page again. The Controller will show the client as auth required. So far the quickest way has been for me to delete the network on iPads and re-enter my settings or create a new profile on a Macbook and join again. I have also had some success when doing a manual DHCP refresh on my Macbook which sometimes seems to kick the Controller into action so it presents the login page to the client again. Whether it is related to the timers on the Controller (5508 running code 7.0.235.3) or - as I just read in another post by Leo - the 20 minute timeout that all Apple devices have built in to conserve battery life
I've recently purchased an E4200, and while it works great, I'd like to use my Apple Airport Extreme (2nd generation) to extend my network to another part of the house that doesn't get as great of a signal. I've become very frustrated trying to accomplish it, and I'm not sure if the problem is more from the Linksys end, the Airport end, or if it's just me.
Is there any way to disable router devices from connecting to your network? For example I want people to connect ethernet cables to their laptops, ps3s, pcs, etc but not to routers. How would one go about doing that?
We added a Belkin N750DB wireless to our building yesterday. Everyone is working fine except one computer that is an apple. Her wi-fi keeps going on and off. Is there a setting we need to change so this stops happening and she has constant internet?
I put just got a wrvs 4400N and when I replaced my old linksys router I can't access my network computers anymore. I'm I missing something or do I need to do some kind of setup?
I have a desktop connected to our work network. It's running XP Pro. I also have a laptop running vista home. Is there a way to hardwire that laptop to the desktop, so i can share files between those two computers, while ALSO keeping my desktop connected to my office network?Since it's vista home, I can't connect the laptop to our network, since it can only connect in workgroups, not networks. But if I'm just able to just use the laptop, create files, and then either save them to a shared folder with my desktop or just save them to the desktop with a switch or something, it wouldn't be a problem that my laptop can't connect to the network.
I have HP laserjet 4000 tn. Had an old router and upgraded to a new wireless router, when connecting it to the new router, the port I connect to has the amber light come on. I have reset to factory setting thinking it would reset and capture a new ip address. still giving me problems. try connecting it to my macbook pro and cannot get a "fix" on the printer either. I know it has to do with the configuration of the printer.
trunk port connecting but not allowing access to tree; i connected 4506 port to 3550 port; and i set both to switchport mode dynamic desirable; the 4506 port was set with switchport mode access and switchport mode access vlan ?; i used the command default switchport access vlan to remove the vlan; the ports are up but as I stated I cannot connect ot our workgroup tree
I have a belkin surf n300 usb wireless N micro adapter. No problems installing this adapter on a HP Desktop running windows 7. I have tried to install on a gateway laptop also running windows y 64 bit. In device manager it show that the product is working. It will not connect to any network. The adapter is an F7D2102 az ver. 2011az
I have a Kguard H264 CCTV system installed that is connected to my BTHome HUb 2 via ethernet cable.The CCTV system is registered on the home hub and has a direct ip address of 192.168.1.100 and is configured to forward port 80 which is correct.Problem is how do i now connect to the CCTV system outside of my home network i.e. using my work computer?
I can find the network OK but whenever I put in the password it just refreshes and tells me I need a password. My son has just got the applemac for his communication studies and neither of us are very bright with computers let alone apple. They are completely different.
I have an iPad 4 (6.1.3) that won't connect to our Cisco 1142 APs. Full Cisco network; 3560 POE switches on edge and Cisco 6509 at the core.At first we looked at it as a wireless issue. No settings changes on the APs would allow the iPad connect. About 125 other iPads of various models worked fine. Took the offending iPad to McDonalds and it connects fine. Took the offending iPad to another school in our District and it connected and worked fine. Went back to the home school, still won't connect. Contacted Apple since iPad was under warranty, sent it to them and they ran diagnostics and it is fine.Is there anyway that the core switch is blocking the iPad client?
Anyway, I am looking for a way to discover host names of Apple devices (namely iPods and iPhones) that are on our network. I've tried a number of programs like Nmap, Advanced IP Scanner, and LanSpy to name a few. All of them will report back the MAC address with no problem but no dice on resolving the host name.
My goal is to use the host name to identify the device, and ultimately the person with the device. Any thoughts on how I can go about this? Is there a setting in Nmap I'm missing or perhaps a better program to use?
