Cisco Routers :: WRVS4400N Block Web Interface From Wireless Accessibility
Feb 13, 2013
Query regarding the Cisco WRVS4400N and Valet M10 routers. How to block the web interface (router login page) from wireless accessibility?
-Our Business is a hotel, so untrusted intruders are our guests.
-Our ISP seeks hotspot methods that we cannot implement.
-Our only solution is routers and an AP to extend internet wirelessly.
the login page or configuration page of the router is always accessible via the gateway address.if the gateway is 192.168.1.1, then a guest can just enter this address and try to guess the password. hacking tools add to the problem.the LAN is working but it is not of certification standards.I seek a way to block wireless access to the gateway login page or physical access only.
View 1 Replies
ADVERTISEMENT
Oct 16, 2011
When i try to active the Internet Access Police with Website Blocking by Keyword, the router WRVS4400N block any access to internet, the Access Restriction by time is disable. How i can active this feature without restrict all the access?
View 1 Replies
View Related
Dec 11, 2012
I have a WRVS4400N I am able to block http sites such [URL] but everybody have access to [URL]
View 2 Replies
View Related
Jul 5, 2011
Right out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies
View Related
Apr 30, 2013
I'm using a RV220W in my home office. Before this router I was. using a Sitecom router which did not cause any problems. I have setup a home network. The RV220W connects to the provider modem. The client components connect to the RV220W. Which acts as DHCP gateway. The DHCP features of the modem are disabled. I have assigned all network client devices to the same workgroup. I have to windows 7 PC's. one of them acts as fileserver. when trying to acces it from the other fixed PC or via a laptop the fileserver is visible but not accessable. I can not open it and access the shared folders.It has worked for a brief moment, but without changing any settings it stop working. I have never had accessability problems with the sitecom router. I have installed the latest firmware and tried rebooting the router several times. I have also started again with the factory defaults.
View 3 Replies
View Related
Apr 8, 2012
I have a WRVS4400N router in a remote office. I have connectivity to the office and computers there. But the web interface for the router is failing to come up. This happens once every few days or so. Is there any utility or something that I can use to remotely reset the router without making use of the webinterface or having physical access to the router?
View 4 Replies
View Related
Nov 8, 2009
I've been keeping an eye on my IPS report tab lately and have been watching a large number of ICMP_SMURF and DOS attacks originating from chinese ip address's. I know I can probably block the offending ip's through the ip based acl tab in the firewall settings, but I'm kind of a newbie how I can block certain ip's from touching my router?
View 3 Replies
View Related
Dec 28, 2011
I am setting up a NAS on my home network. My computer sees it on the network and accesses it without a problem. My wife's computer, however, only sees it on the network, but will not access it. (Both computers are Win 7 machines.) It will access it if I type in the ip address of it, but that is beyond my wife's patience level for her to do each time she wants to access the storage. She can, however, access the shared folders on my computer and vice versa. Both computers go through the same router. The NAS is connected to another router attached to the main router (extending it since we ran out of slots on the main one). Both routers are Linksys (1 is E3000).
View 7 Replies
View Related
Sep 13, 2012
I have Comcast as my ISP and their Small Business Gateway Router/Firewall. I purchased a WRVS4400N and configured them like this:
Comcast Router/Firewall - 10.1.10.1
Cisco WRVS4400N - 10.1.11.1
I turned DHCP off on the Cisco so that wireless devices that connect to it get a 10.1.10 address from the Comcast device. Now, I am completely unable to connect to the web interface of the Cisco, whether connected to it wirelessly or even if I plug directly into one of the LAN ports on it. I have one of the LAN ports on the Cisco connected to one of the LAN ports on the Comcast. What am I missing here? I'm guessing I'm not able to see the 10.1.11 addresses when I am getting a 10.1.10 address from the Comcast, even though I'm connected to the Cisco?
View 6 Replies
View Related
Jan 6, 2012
I have installed a WRVS4400N router in a client's office. When laptops are plugged into the router everything works fine. When they are attached via the wireless signal it drops frequently. WPA personal is being used to encrypt. I have also installed the latest firmware and am having the same results. What can be done to eliminate the drops?
View 10 Replies
View Related
Aug 19, 2012
I have an ongoing problem with my WRVS4400N router. It reboots on it's own when streaming video through a wireless connection (computer, xbox, roku, tv). Once I make a wired conection, it performs flawlessly. The firmware is up to date. I have read some reviews of this router on Amazon stating the same problem, but I expected it to be solved with firmware update. Unfortunately, this was not the case.
View 4 Replies
View Related
Jun 2, 2013
I need trouble-shooting wireless network connectivity issues that arose recently:We use a Comcast modem and two WRVS4400N's as wireless routers/wireless access points.We recently got our comcast service upgraded to 100/20 and also got rid of our static ip address. As a result (I think there must be a sort of causal relationship here, but I'm not sure what it is) we can no longer connect to the internet using our wireless networks. We can connect to the wireless network, but have "No Internet Access."
View 4 Replies
View Related
Jul 17, 2011
I have several wired and wireless devices connected to the router which is running the latest firmware (2.0.2.1) and I have this issue with all wireless devices. The router is configured for B/G/N Mixed, Channel 6, and to broadcast the SSID. Security Mode is WPA2-Personal w/ key renewal set to 3600. Connection control is configured to allow only the desired MAC addresses. All wireless clients are configured for DHCP (as are some of the wired clients that do not have this issue). I have tried various setting changes over time, none of which have resolved the issue.
What I have determined, and may be useful, is that each time this occurs I am unable to ping the router from the client and have no connectivity to the internet or other devices on the network. If I ping the WAP address (reserved for internal use address) I get a response and then connectivity is always restored after doing so. In other words, I ping 192.168.1.1 and get no response, immediately ping 192.168.1.2 and get a response, then immediately ping 192.168.1.1 and now get a response and connectivity is restored. If I skip the first step and just ping the reserved address followed by the router address result is always the same. It would appear the issue is between the the two router addresses.
Prior to owning this router I had a Linksys BEFSX41 that I had for about 7-8 years and a WAP54G I had for about 5, both of which still worked and I never had this issue with my wireless clients. I went to this router for the increased performance and am very happy with that aspect, however this issue is unacceptable.
View 6 Replies
View Related
Jan 27, 2013
We have an office with about 10 PCs, and several other network devices (smartphones, printers, etc). Some PCs and printers are wired, some are not. About two weeks ago, some (6) of the wireless devices lost connectivity. Since then, some (4) of the devices have also recovered normal connectivity.
As of right now, there are two computers, a laptop and a desktop, that cannot use the wireless network. They see the wireless network, connect to it, receive an IP via DHCP properly, have correct DNS servers listed in ipconfig, but they can't ping the router, use the intranet, or internet.
View 1 Replies
View Related
May 1, 2013
What would be an acceptable number of wireless connections to a WRVS4400N router? I'm working in the IT department for a new company, and one of the offices complains that using VoIP and doing large file transfers are constantly a problem. They are all connecting wirelessly to the WRVS4400N. I managed to vpn in and connect to the web interface of the router, and it shows that there are 30 devices connected wirelessly to it. However, when people plug into the wall jack VoIP and data seem to work fine.I can't find any info on what a best practice would be for number of wireless connections to the router. There's no Vlans setup on it from what I can tell, so that may be my next step, to separate data and voice traffic.
View 2 Replies
View Related
Jul 18, 2012
I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.
View 4 Replies
View Related
Apr 16, 2012
I see a lots of problem associated with wirless connectivity with WRVS4400N, with following config
Firmware version - Firmware Version: V1.1.13
Wireless connectivity - G/N Mixed
Auth - WPA2 AES
Everything else default and AUTO,
Problem:The end devices suddenly drop connection. Wired connection works just fine. The DROPPED device can not be reconnected. On MAC I get AUTH time out. I see the SSID being broadcasted from my HTC wireless analyster so radio may not be the problem. I changed to set the speed to G only or N only but not avail. ONLY way to recover from this is rebooting the router.
View 2 Replies
View Related
Jan 21, 2012
I've just purchased WRVS4400N VPN router and installed it. This was a replacement of a old Linksys router. After installing the router, I've started seeing wireless drops, packet drops and latency on pings. I've installed the latest firmware, disabled Firewall services, disabled IPS. No changes at all. As a basic example, I am pinging my NAS device (hard wired to router) from a laptop connected to wireless below. Previously while connected to my old linksys router the time was equal to no more than 2ms.
View 4 Replies
View Related
Mar 10, 2012
When clients connect wirelessly to the WRVS4400N they successfully get a DHCP address from the Windows 2008 server. After they have the address they can no longer access the server. It cannot be pinged, no drives can be mapped and internet access fails because the same server is running DNS. The WRVS4400N is setup for DCHP relay to the server. Wired clients do not have this problem. Wireless clients that connect to a secondary WAP on the same LAN also do not experience this problem. I have updated the router to the latest firmware version, reset it to factory defaults and reconfigured from scratch. Turning the server firewall off has not made any difference either. I have been able to bypass the internet problem by adding a second external DNS server in the DHCP scope options.
View 5 Replies
View Related
Jun 18, 2012
Is it possible to telnet into the 'WRVS4400N Wireless-N Gigabit Security Router with VPN' router? When I try it says the remote system refused the connection.
View 5 Replies
View Related
Feb 11, 2013
I have an 1841 between my firewall and the ISP. Three interfaces - multilink to ISP, FA to my firewall, and FA to my inside network. I use the inside interface for configs aand snmp access, etc. Only my ISP-assigned fixed address block will get routed to the multilink by the ISP but I am nervous about the inside interface sitting on my LAN. I know I can remove it, but if I keep it there, how can I set up an ACL so that all traffic from the multilink interface is denied to the inside interface? I suppose another way to think about it that the inbound iface can only accept traffic from its own outside, not from the router.I think this is fairly simple but I don't want to knock down the traffic if I get it wrong.
View 8 Replies
View Related
May 2, 2013
I was asked to block pings from the internet to the outside interface of our ASA-5505 firewall. I found a post that said to enter "icmp deny any outside", however that does not do it.
I created an ACL to try and do the trick, also to no avail:
access-list outside_in extended permit icmp any any echo-reply
access-list outside_in in interface outside
access-group outside_in in interface outside
View 8 Replies
View Related
Jun 23, 2011
Recently, I've been having significant problems with denial of service on our ASA-5510. Two IP addresses in particular attack my ASA regularly. What kind of rule do I need to create to deny these IP's access to my firewall?
View 4 Replies
View Related
Mar 29, 2012
I'm working on creating an open wireless scheme and we are simply going to use WPA with a key. What I'm getting a little stuck on is preventing access, by the guests that will connect to the WAPs, to the gateway/management webpage. I've been looking into seperating with VLANs and trunks (internal with management access and external for guests) but having a hard time with the configuration scheme.
Not sure if there is an easy way to just block that in the config or what.
View 1 Replies
View Related
Dec 17, 2012
I have a Belkin N750 router which I purchased because the box said it had filtering options. I didn't realize that the filtering was only sites that Norton kept track of. There are certain adware sites I know about that I would like to filter. Possible with this router?
View 5 Replies
View Related
Dec 7, 2011
I'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies
View Related
Mar 3, 2013
I'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
View 2 Replies
View Related
Sep 16, 2011
Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?
View 1 Replies
View Related
Sep 15, 2012
I have successfully got QuickVPN working from Windows 7 64bit into my WRVS4400n. The router is sat behind another router/modem (Belkin) as the UK uses PPPoA and the WRVS4400n doesn't.So I set up DMZ and changed the DHCP to always allocate 10.x.x.2 on the Belkin which is the WAN side for the WRVS4400n as it is the only thing attached.I have now noticed, and I'm not sure whether it was the case before, that the DNS that the WRVS4400 is showing is the LAN address for the Belkin Modem/Router (10.x.x.1), not 192.x.x.1 for the WRVS4400n itself. I assumed setting the Static DNS 1 on the WRVS4400n would do it, but it didn't?When I connect into the network with QuickVPN, the computer names do not show even though I have selected the option in QuickVPN?
View 1 Replies
View Related
Aug 8, 2011
Our business was looking at purchasing one of these Cisco routers and were curious if it supported WPA2 EAP-TLS?
View 2 Replies
View Related
Jul 23, 2012
I have 2 WRVS4400N's available to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies
View Related
Dec 16, 2012
Recently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
View 1 Replies
View Related
Aug 5, 2012
I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
View 2 Replies
View Related
