When i try to active the Internet Access Police with Website Blocking by Keyword, the router WRVS4400N block any access to internet, the Access Restriction by time is disable. How i can active this feature without restrict all the access?
View 1 Replieswe've buyed a WRVS4400N to create a IPSEC VPN tunnel to our client in order to access some applications.
After a while trying to configure the router, we have archieved it and the VPN tunnel is up. We can see the tunnel up from here and from client's side as well.
Our client supposendly have created the tunnel in order to access a list of specific IPs in the range 10.113.x.x, but if we try to access this IPs via telnet whe cannot obtain any response.
Making a tracert, we obtain...
C:UsersHuexxx>tracert 10.113.56.177
Traza a 10.113.56.177 sobre caminos de 30 saltos como máximo.
1 1 ms 1 ms 1 ms 192.168.0.1
2 * * * Tiempo de espera agotado para esta solicitud.
3 * * ^C
... and therefor the client doesn't receive any packet at its firewall.
I've tried to establish a static route for 10.0.0.0 255.0.0.0 to their remote gateway, but I'm unable to add any entry to static routing list... The router tries to do something, but afterall I cannot see the new entry...
What can I do to route the traffic through the tunnel?
Query regarding the Cisco WRVS4400N and Valet M10 routers. How to block the web interface (router login page) from wireless accessibility?
-Our Business is a hotel, so untrusted intruders are our guests.
-Our ISP seeks hotspot methods that we cannot implement.
-Our only solution is routers and an AP to extend internet wirelessly.
the login page or configuration page of the router is always accessible via the gateway address.if the gateway is 192.168.1.1, then a guest can just enter this address and try to guess the password. hacking tools add to the problem.the LAN is working but it is not of certification standards.I seek a way to block wireless access to the gateway login page or physical access only.
I have a WRVS4400N I am able to block http sites such [URL] but everybody have access to [URL]
View 2 Replies View Relatedis it possible to block outgonig multicast L2 frames on an Ethernet port in outgoing direction on a 2960 Switch?
I tried the "switchport block multicast" command, but the description of this feature relates to only "unknown" multicast!?
But what means "unknown multicast"? Even if activated, I see a lot of multicast traffic going out that port: IGMP, PIM, SSDP, HSRP, OSPF, .. and also pings and VLC streams to multicastaddresses (ip igmp snooping disabled).
I also tried to map a "mac access-list" to that port, but the "mac access-group" interface command is restricted to only incoming traffic.
Reason: we assume, that there are a couple of specific enddevices, that might react strange to some multicast. Therefor we would like to block outgoing multicast on that specific ports.
I tested it on a 2960 12.2(53)SE2
Can I use AAA Radius on a ASA 5505 to block outgoing user access by user name in a group?
View 2 Replies View RelatedAfter updating the firmware of my WRVS4400N from V 2.0.1.3 to 2.0.2.1 all traffic was blocked for all machines, even some not included in the list of PCs. As the log was showing that all traffic was blocked by access policies, I disabled the only rule I had (blocking access to some sites to some MAC address list) and everything worked fine.I tried creating a new, simpler rule but after activation it blocked again all traffic for all the LAN.After many trials, I decided to roll back to the previous V2.0.1.3 which solved this problem.
View 1 Replies View RelatedI am trying to create an IAP for a single computer based on it's MAC address. I want to block certain keywords and websites 24/7. When I setup the IAP as number 1, I add the MAC address of the computer in question. I then Select Allow and choose Everyday and 24 Hours. I type in the forbidden domains and click add after each one. I type in the keywords and click add after each one. After I click on Save, all of my computers on the network lose internet access.
I have WRVS4400N VPN Version 2, firmware version 2.0.2.1
I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.
I have a Cisco WRVS4400N on the latest firmware and I have just had my Virgin internet connection upgraded to the 100Mb. Once i thought it was upgraded i checked with a broadband speed test and it came back as 15Mb download and 5Mb upload. Before i rang Virgin i thought i'd check with a direct connection from my pc straight to the modem. Ran the speed test and it came back as 100Mb download and 5Mb upload. I thought the best thing to do is restore my settings back to factory and its still the same.
View 7 Replies View RelatedRecently I upgraded my Internet speed at the ISP from 10Mbps to 25Mbps and the problem is that I am measuring only 15Mbps using [URL]On the day when the tech came out to install the new DSL modem, he noticed the difference and as part of troubleshooting, he bypassed the Linksys router and voila the net speed measured 25Mbps using speedtest.net.So, why my Linksys WRVS4400N V1.1.13 acts like a bottleneck in this case? I didn't have this problem at the speed of 10Mbps. The upload speed is OK, it is 5Mbs with or without the DSL modem.
View 2 Replies View RelatedFor eight months we have not had any problems with our new WRVS4400N (V2.0.2.1) connected to a Verizon/Westell 6500 to provide DSL internet for our network with DHCP on our server... No changes have been made to the router or modem since initial setup; but, then it started -- Our internet connection would drop intermittently. Sometimes every 5 or 10 minutes - sometimes every hour. Verizon has tested the lines which came up ok, then they sent a tech who changed the wire pair coming into the building for the DSL line and retested the lines which again came up ok, then they provided us with a new modem (now a Verizon/Westell 7500). After all that, the DSL still connects then disconnects intermittently. I am now wondering if the issue lies with the WRVS4400N.
View 2 Replies View RelatedI've been keeping an eye on my IPS report tab lately and have been watching a large number of ICMP_SMURF and DOS attacks originating from chinese ip address's. I know I can probably block the offending ip's through the ip based acl tab in the firewall settings, but I'm kind of a newbie how I can block certain ip's from touching my router?
View 3 Replies View Relatedi want block only internet access from firewall
View 1 Replies View RelatedI have both WAN1 and WAN2 connected to an ISP but only WAN2 should be used for outgoing mails. How and where can I specify this in the configuration?
View 3 Replies View RelatedWe have an RVS-4000 router that we use as an Internet gateway on our school network. I am trying to set up an Internet Access Policy to block some specific websites by URL using a domain name. I set up the policy, and added a PC to the list using the mac address, and the blocking did not work. I went back to the list and added the IP address of the same PC, the policy still did not work to block the domain. I rebooted the router, cleared the Internet Temporary files and history on the PC, and the policy still does not work. It acts like it is going to block access to the website because it takes a long time, but it will eventually connect.
View 7 Replies View RelatedRight out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies View RelatedI'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies View RelatedI'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?
View 1 Replies View RelatedI have successfully got QuickVPN working from Windows 7 64bit into my WRVS4400n. The router is sat behind another router/modem (Belkin) as the UK uses PPPoA and the WRVS4400n doesn't.So I set up DMZ and changed the DHCP to always allocate 10.x.x.2 on the Belkin which is the WAN side for the WRVS4400n as it is the only thing attached.I have now noticed, and I'm not sure whether it was the case before, that the DNS that the WRVS4400 is showing is the LAN address for the Belkin Modem/Router (10.x.x.1), not 192.x.x.1 for the WRVS4400n itself. I assumed setting the Static DNS 1 on the WRVS4400n would do it, but it didn't?When I connect into the network with QuickVPN, the computer names do not show even though I have selected the option in QuickVPN?
View 1 Replies View RelatedOur business was looking at purchasing one of these Cisco routers and were curious if it supported WPA2 EAP-TLS?
View 2 Replies View RelatedI have 2 WRVS4400N's available to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies View RelatedRecently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
I'm having a heck of a time connecting the WRVS4400N VPN to another WRVS4400N VPN. both of the routers have the current firmware version V2.0.2.1: Router 1 is below, and router 2 has the matching configuration with as it should be the local group being that routers local information and the remote crew set up being router ones information. the status is up on both of the routers, but I'm unable to ping the remote gateway or any device behind it.[code]
View 5 Replies View RelatedAfter a few months of trouble-free ... the Cisco WRVS4400N V2 stopped working. i have tried to reset by holding the reset button for 30 seconds ... but nothing changes the red DIAG light remains on at all times
i have also tried two different versions of the Firmware Rescue Utility but all i get is "unable to scan"
How to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.
This is a new device, just initially installed about a week ago. I updated to the latest firmware. We have iphones, ipads, and Samsung Galaxy smartphones all trying to connect to this WAP at this office, but cannot seem to connect. If I power cycle the WAP, we can connect for about 5 min, then it loses it and cannot connect again. I have strong signal, device says "connecting" then immediately "disconnected"... does this on loop forever.WPA/WPA2 PSK.I don't know what to do. About to go buy an Apple WAP.
View 3 Replies View RelatedMy WRVS4400N is not letting my VPN client through the router. I have checked the passthrough boxes for all 3 protocols. I have port range forwarding for my VPN connections to my SBS2008 box on port 1723.
View 5 Replies View RelatedI have a Linksys E4500 as the main router and would like to use the WRVS4400N as a bridge to extend the range of my network and also attach a NAS to it. Is this possible? I've been trying different options but have been unsuccessful.
View 1 Replies View RelatedLooking for a working Cisco VPN client for Windows 7. There seems to be an availabel download for a ver 5, but you have to be a reseller etc.. Where do I download the Windows 7 supported VPN client to access my WRVS4400N router? If none, should I use 3rd party - IF yes to 3rd party, which one would you suggest?
View 1 Replies View RelatedI bought a WRVS400N v2 to be used as an access point. Currently it is hooked up on my switch via a trunk port and is able to communicate with my gateway. Whenever I try to access an IP subnet other then the local IP address of the WRVS, I get a network unreachable error. To fix this for my local networks, I added the appropriate static route to cover my local LANs and that seems to work now. I tried to add route 0.0.0.0/0.0.0.0 using the web interface for internet access, but somehow it does not recognize this as a default route (quad zero!?). Does any know how I can set the default gateway in this router? Maybe, but hopefully not, I have to use the WAN port to create some kind of uplink and use one of the LAN ports to connect using the trunk port and route traffic for the clients over the WAN port .
View 1 Replies View Related