Cisco Routers :: WRVS4400N - VPN Tunnel Up But No Outgoing Traffic?
Jan 29, 2012
we've buyed a WRVS4400N to create a IPSEC VPN tunnel to our client in order to access some applications.
After a while trying to configure the router, we have archieved it and the VPN tunnel is up. We can see the tunnel up from here and from client's side as well.
Our client supposendly have created the tunnel in order to access a list of specific IPs in the range 10.113.x.x, but if we try to access this IPs via telnet whe cannot obtain any response.
Making a tracert, we obtain...
C:UsersHuexxx>tracert 10.113.56.177
Traza a 10.113.56.177 sobre caminos de 30 saltos como máximo.
1 1 ms 1 ms 1 ms 192.168.0.1
2 * * * Tiempo de espera agotado para esta solicitud.
3 * * ^C
... and therefor the client doesn't receive any packet at its firewall.
I've tried to establish a static route for 10.0.0.0 255.0.0.0 to their remote gateway, but I'm unable to add any entry to static routing list... The router tries to do something, but afterall I cannot see the new entry...
What can I do to route the traffic through the tunnel?
View 1 Replies
ADVERTISEMENT
Oct 16, 2011
When i try to active the Internet Access Police with Website Blocking by Keyword, the router WRVS4400N block any access to internet, the Access Restriction by time is disable. How i can active this feature without restrict all the access?
View 1 Replies
View Related
Aug 5, 2012
I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
View 2 Replies
View Related
Dec 17, 2011
I have establlished VPN tunnle between 2 locations
I can ping accros and access server resources on both LANs The problem is that from one location I can not access Internet
I can not ping by IP,when I do tracert it just reaches default gateway of this locations from other location(office) no problem
View 1 Replies
View Related
Jul 24, 2012
Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies
View Related
Dec 7, 2011
I have 2 WRVS4400N's installed in our network, one at each end of a VPN tunnel between 2 physical locations. I continue to have issues with the VPN to "Stay" connected, even after purchasing another new WRVS4400N 4 months ago. I can reboot both routers, and the VPN connects with no problem, but hangs up after a few hours / days (no pattern).
I am taking a hard look at the issue now, as about 1 month ago, the newest router "automatically" reset it itself back to factory settings (thus interrupting nearly everything in our network). After contacting support, we reset the router and re-configured it to our environment. It is plugged into a surge protected UPS (yep, I thought maybe a power issue caused the problem, but it's not). Then about 1 week ago, the other/older (9 month old) router lost it's configuration. again, reset it and all works. Including the VPN, but the VPN still works as it did before connects for a while, but then drops and generally I need to reboot the router to get it connected again (clicking on the Connect on either router doesn't work until after a reboot).
Also, in light of the recent "lost configurations", I turned on logging and now I'm getting TONS of emails of log activity, even when the network is idle (no users, no background jobs running).
after rebooting and no inter activity, I get this kind of log, all night long (to me it generally looks like the VPN connection resets and increments by 1... I'm taking a guess that the increment hits a limit someplace and I lose my VPN).[code]
View 6 Replies
View Related
Oct 5, 2011
i want to set WRVS4400N Route all traffic through, it function as same as sonicwall Route All.
View 1 Replies
View Related
Jun 9, 2011
I have on my ethernet linux box, that is responsible for IPv6. This box is configured as IPv6 gateway from my network and it also sends RA to the network. All devices on ethernet network can work on IPv6 without problem. Clients, that are connected to WiFi, they just receive the RA from this box -> this packet is sended over WRVS4400N to the wifi network. But all other traffic do not pass the WRVS4400N, so the wifi client is not able to ping the IPv6 gateway. There is no problem on IPv4, there the wifi client is able to communicate with any ethernet device.I have tested WRVS4400N setting "ipv4 only". If I switch on "ipv4 and ipv6", than all devices will get some additional IPv6 adresses and the communication from WiFi client to IPv6 router is not working again. How to configure the WRVS4400N to bridge all IPv6 traffic between WiFi and ethernet?
View 2 Replies
View Related
Apr 5, 2011
I am monitoring my WRVS4400N with SNMP and create graphs by MRTG. Problem is that data about traffic are strange, very low. I have 50 MB line but max traffic shown on graphs is about 8000 bits per second. Also the "shape" of graph does not correspond with real traffic.
View 1 Replies
View Related
Feb 13, 2012
I'm trying to setup a VPN between an RV042 V3 and an RV082 V2 router. They get connected but no traffic gets through the tunnel. I tried with and without firewall,DPD, Keepalive, forward secrecy but nothing worked. What should I do? I don't want to throw out the V2 routers. V3 to V3 connects fine.
View 1 Replies
View Related
Jan 23, 2012
There are a few situations were I'd like to be able to use the locally configured account on a device but still have ACS in place.I want to complete this WITHOUT adding the locally configured account into ACS.I have tried setting the advanced option under Identity for if an account is not found to "Continue" however this causes the account to be allowed as long as a password is typed (any password, as long as its not blank).
View 2 Replies
View Related
Apr 3, 2012
I am using a RV110W as a VPN client to establish a VPN conection since some months. So far everything works fine. But all traffic is routet thru the VPN tunnel. Now I try only to route specific adresses thru the tunnel but not the internet acess.
RV110W is in Gateway mode
WAN interface is connected with internet
I am using PPTP with PAP and MPPE for VPN
so far no static routes (I could not set e.g. a route to 0.0.0.0 because web-interface says its not a valid adress)
Goal is to route only traffic for the target network thru tunnel and the rest direct via WAN interface.
View 3 Replies
View Related
Oct 12, 2012
cisco 2651XM router with WIC1 adsl card and NM-16ESW switch
IOS: c2600-ipbasek9-mz.124-23.bin
I use the following config to export traffic from the adsl card to a fasterthernet port so I can look at the adsl traffic in wireshark on a pc:router(config)#ip traffic-export profile my_rite router(conf-rite)#int FastEthernet 0/0 router(conf-rite)#bidirectional router(conf-rite)#mac-address abcd.efgh.ijkl (mac address of PC) router(conf-rite)#exit router(config)#int dialer0 router(config-if)#ip traffic-export apply my_rite this config works and I can see stuff going on in wireshark but it's only one way. This config only shows traffic going out from my adsl card, but no incoming. There is defintely traffic going both ways because everything about my adsl connection is working perfectly. I've tried using a different fastethernet port, even tried exporting to a different pc but all I see is outgoing ie: source is my public ip address but never as destination . I have bidirectional in the config but it still only shows outgoing. I even tried a different IOS (c2600-adventerprisek9-mz.124-15.T8.bin) but still it doesn't show incoming traffic. Could it be my ISP in some way hiding incoming traffic from view?
View 3 Replies
View Related
Jan 2, 2013
Is it at all possible to channel all/some data traffic through an established ipsec tunneled connection using the RVL200? I have successfully established an ipsec connection through RVL200 and RV042 routers and are able to connect to servers/computers behind it.Now I want to channel all or some traffic through the ipsec-tunnel for computers that reside on 192.168.1.0 subnet of RVL200 network.
Main office - RV042 router - 10.200.62.1
Remote office - RVL200 router - 192.168.1.1
I am trying to use the Advanced Routing option to add static routes but I am not 100% sure if I am configuring the routes correctly.To give an example of routing DNS requests for HOTMAIL.COM [65.55.72.183]: [code]For some reason this does not appear to work. I have also tried using the interface setting of WAN and tested - this also does not work.
View 10 Replies
View Related
Apr 25, 2012
For ASA v8.3 and above we don't need to use nat-controll, traffic from high security interface can go to low security interface without matching NAT statements.So does the ASA automatically NAT s the outgoing traffic to the outside interface by default?
For example
ASA inside int---10.1.1.1
outside int---120.11.1.1
when the inside hosts try to go out they will be NATed to 120.11.1.1 by default on version 8.3 and later.is that right?
View 7 Replies
View Related
Oct 9, 2012
I want to be able to use port 1-80 for all outgoing traffic. I have a VPS outside my home, which can redirect the packets to the prober ports.Is it possible with an application on the computer and VPS? Or is it impossible?
View 1 Replies
View Related
Feb 6, 2012
I have a licensing server. Other computers need to turn on a program, they send a message to the licensing server, and it responds that they have permission to run.Until today the licensing server was plugged into its own ethernet wall socket and configured with a static IP address. Today I put a router into that wall socket and now the server's plugged into the router.The router (WRT-54G) was set to the static IP - and now the internet on its network works. I set all ports to be forwarded to the server's internal IP address - and now my programs can detect and ping it. But now the server won't send back permissions to use licensed software, or even reply with a list of the software which it can license.
View 1 Replies
View Related
Dec 30, 2011
I cannot get my server to send outgoing traffic through my network. I.e. If i try to connect to any of my services i get a very weak connection. Now, i can still CONNECT, i just don't get any data flow. I cant even PING the server internally, it just times out. Now, regardless of whether i use my internal IP/external domain, i get the same issue. I logged onto my computer and tried a speed test the download was normal (around ~20mbit) but the upload times out.
Here is the fun part, if i connect to the server using a switch, everything works fine! Is it my router or some stupid configuration issue? Router is a WRV54G (I hate this thing). Server is running windows 2008 and has a virtual machine.
View 3 Replies
View Related
Apr 7, 2012
i'm using an rv220W and i whant to know if is it possible to assign vpn traffic to a vlan when i setup an ipsec tunnel?
example:
Im using different vlans on my rv220W.
Vlan 10: engineers (ex: 192.168.1.0/27) no intervlan routing
Vlan20: sales (ex: 10.0.123.0/24) no intervlan routing
This is what i need: - An engineer is on the road and when he makes a ipsec vpn connection => assignd to the vlan "engineers" so he can access the server/pc's in that vlan.and when someone from the sales group starts a vpn connection he needs to be in the vlan "sales" so he can access his pc/data,...
View 15 Replies
View Related
Oct 9, 2012
I have a Cisco 527w which we are wanting to deploy to our remote sites however i've found a bug. We use ADSL with an IPsec tunnel as primary and 3G APN for failover . When the ADSL goes down the route via the IPSec tunnel remains and i am unable to route the traffic via the APN backup without disabling the VPN tunnel .
View 0 Replies
View Related
Sep 13, 2011
I configured ASA5520 and RV042 for site-to-site IPSec VPN tunnel.Tunnel get connected, but no ping, no traffic between both end network.
Network:
=======
192.168.113.0/24----------192.168.113.6 -ASA--------public, static IP address------Cisco 2821--------Internet
192.168.10.0/24-----------192.168.10.1 -RV042-----public, static IP address------Cisco 2821--------Internet
ASA5520 config:
----------------------
name 192.168.10.0 VPN
!
interface GigabitEthernet0/1
nameif NET
security-level 100
ip address 192.168.113.6 255.255.255.0
[code]....
View 5 Replies
View Related
Jul 14, 2011
I have got a Cisco router connected to a LAN and to the internet.I was wondering if I could nat https traffic from inside to internet to a local server (Proxy) on a given port for example tcp 8080.
int tunnel0
ip address 192.168.0.1 255.255.255.0
ip nat inside
int fa0/1
des internet connexion
ip address 41.x.x.x.x 255.255.255.248
ip nat outside
ip access-list extended Proxy_Redirect
permit tcp 192.168.0.0 0.0.0.255 any eq 443
View 1 Replies
View Related
Aug 4, 2012
I am trying to limit the incoming and outgoing traffic on a l2 port to 8mbps for a ip subnet within the nexus 7000. The port is connected to my ISP router which has a bandwidth of 20mbps.Policing won't work on a l2 Port and shaping cannot be applied on a port level. url...I have been reading thru the qos guide for nexus release v6 and have problems understanding the different queues.
View 3 Replies
View Related
Mar 4, 2013
We have a Cisco ASA 5520 and im looking for a way to monitor largest outgoing and incoming traffic per ip in real time so to know which of my internal computers are using the most of our Internet Line. Is there a way to this through ADSM ? We use version 6.3.
View 1 Replies
View Related
Jan 9, 2011
i have a 7201 router with NPE-G2. i have a design which i have the option to send all the traffic through a GRE tunnel or a L2TPV3 tunnel.which method is more CPU consumption ?
View 1 Replies
View Related
Mar 14, 2011
I have a VPN tunnel with an WRVS4400N (teleworker) on one side and sonicwall firewall on the other. I need the telework's router to know to push two ip's through the tunnerl, 9.19.178.( ) and 172.20.0.( ). It looks like when you setup the tunnel you can only do one. The tunnel does work with 9.19.178.( ) but how do I tell the router to also push 172.20.0.( ) traffic through the tunnel as well?
View 1 Replies
View Related
Mar 21, 2012
I'm trying to establish a VPN tunnel between our main office running a Cisco ASA 5505 [8.3(2)] and a remote user using a Cisco Small Business WRVS4400N firmware version V2.0.1.3.
The Cisco ASA 5505 is already configured to allow incoming IPSec VPN connections via the Cisco VPN Client.
Is this possible, and if so, how would I go about doing so? The remote user has a static IP address as well as the main office.
I'm trying to establish a VPN tunnel between our main office running a Cisco ASA 5505 [8.3(2)] and a remote user using a Cisco Small Business WRVS4400N firmware version V2.0.1.3.
The Cisco ASA 5505 is already configured to allow incoming IPSec VPN connections via the Cisco VPN Client. Is this possible, and if so, how would I go about doing so? The remote user has a static IP address as well as the main office.
View 2 Replies
View Related
Oct 15, 2012
I have both WAN1 and WAN2 connected to an ISP but only WAN2 should be used for outgoing mails. How and where can I specify this in the configuration?
View 3 Replies
View Related
Dec 15, 2011
All of my remote sites use various routers to route all of their traffic via IPsec. However, I have one WRVS4400N w/firmware 2.0.2.1 configured with a working tunnel. My issue is I need to set the Remote Group to 0.0.0.0 0.0.0.0 so all traffic is forced via IPsec tunnel and not out the local gateway. When I do the error, Remote Security Group and Local Security Group cannot be in the same network. However, it works with Cisco/Linksys RV042.
View 3 Replies
View Related
Oct 17, 2012
I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
View 3 Replies
View Related
Oct 6, 2011
i want to set WRVS4400N Route all traffic through
it function as same as sonicwall Route All
[URL]
View 1 Replies
View Related
Nov 15, 2011
Currently I have users that connect with the Cisco VPN client to our PIX 515e. Our corporate network is also directly connected to our partners network, sharing common address space. I want to be able allow our VPN users to connect to certain resources on their network. Since they already have routing for our address space, can I allow the VPN to only NAT traffic to certain destination addresses with a local IP address on our network? That way the partner's network does not have to change any routing since they would see the source address as a local IP on our network.
View 1 Replies
View Related
Nov 6, 2012
I try to make a gre tunnel with 2 cisco routers 2901, ping responds between tunnel ip's ends, but I don't have pings from the pc's inside the networks. [code]
View 7 Replies
View Related
