Cisco Routers :: WRVS4400N V2 And IPv6 Traffic Bridge Between Wi-Fi And Ethernet?
Jun 9, 2011
I have on my ethernet linux box, that is responsible for IPv6. This box is configured as IPv6 gateway from my network and it also sends RA to the network. All devices on ethernet network can work on IPv6 without problem. Clients, that are connected to WiFi, they just receive the RA from this box -> this packet is sended over WRVS4400N to the wifi network. But all other traffic do not pass the WRVS4400N, so the wifi client is not able to ping the IPv6 gateway. There is no problem on IPv4, there the wifi client is able to communicate with any ethernet device.I have tested WRVS4400N setting "ipv4 only". If I switch on "ipv4 and ipv6", than all devices will get some additional IPv6 adresses and the communication from WiFi client to IPv6 router is not working again. How to configure the WRVS4400N to bridge all IPv6 traffic between WiFi and ethernet?
View 2 Replies
ADVERTISEMENT
Oct 11, 2011
I just spent a number of hours getting a site-to-site VPN tunnel and Cisco Quick Connect client running on my WRVS4400N and RVS400. Turns out the problem was the routers don't route IPv6 properly and it takes precedence over IPv4
View 1 Replies
View Related
Oct 17, 2012
I have a Linksys E4500 as the main router and would like to use the WRVS4400N as a bridge to extend the range of my network and also attach a NAS to it. Is this possible? I've been trying different options but have been unsuccessful.
View 1 Replies
View Related
Oct 5, 2011
i want to set WRVS4400N Route all traffic through, it function as same as sonicwall Route All.
View 1 Replies
View Related
Jan 29, 2012
we've buyed a WRVS4400N to create a IPSEC VPN tunnel to our client in order to access some applications.
After a while trying to configure the router, we have archieved it and the VPN tunnel is up. We can see the tunnel up from here and from client's side as well.
Our client supposendly have created the tunnel in order to access a list of specific IPs in the range 10.113.x.x, but if we try to access this IPs via telnet whe cannot obtain any response.
Making a tracert, we obtain...
C:UsersHuexxx>tracert 10.113.56.177
Traza a 10.113.56.177 sobre caminos de 30 saltos como máximo.
1 1 ms 1 ms 1 ms 192.168.0.1
2 * * * Tiempo de espera agotado para esta solicitud.
3 * * ^C
... and therefor the client doesn't receive any packet at its firewall.
I've tried to establish a static route for 10.0.0.0 255.0.0.0 to their remote gateway, but I'm unable to add any entry to static routing list... The router tries to do something, but afterall I cannot see the new entry...
What can I do to route the traffic through the tunnel?
View 1 Replies
View Related
Apr 5, 2011
I am monitoring my WRVS4400N with SNMP and create graphs by MRTG. Problem is that data about traffic are strange, very low. I have 50 MB line but max traffic shown on graphs is about 8000 bits per second. Also the "shape" of graph does not correspond with real traffic.
View 1 Replies
View Related
Dec 7, 2011
I buy a WRVS4400N router on amazon.fr because on cisco.com, the Product Specifications say "Dual-stack IPv4 and IPv6" [URL]
The ipv6 work for the local network. But the router does'nt fetch my IPv6 take by my ISP (by PPPoE) How do I get IPv6?
View 5 Replies
View Related
Oct 9, 2012
Since this router already set up for IPv6 and Dual-Stack traffic, would it be possible to give it the ability to get its IPv6 prefix from the WAN side of the router.
Example:
I have Comcast, and as long as my modem and router support IPv6, with the router also supporting DHCPv6-PD to get the /64 prefix from comcast.
I now have an RV180W so this is not an issue for me, but my father is inheriting the WRVS4400N from me and he is also on Comcast.
View 2 Replies
View Related
Oct 9, 2011
below is my sanitized ASA 5510 config. got an IPv6 T1 from at&t and im unable to pass any traffic from my LAN clients out.
:
ASA Version 8.2(2)
!
enable password PoBmYYxuAzCciKRA encrypted
[Code].....
View 6 Replies
View Related
Dec 15, 2011
All of my remote sites use various routers to route all of their traffic via IPsec. However, I have one WRVS4400N w/firmware 2.0.2.1 configured with a working tunnel. My issue is I need to set the Remote Group to 0.0.0.0 0.0.0.0 so all traffic is forced via IPsec tunnel and not out the local gateway. When I do the error, Remote Security Group and Local Security Group cannot be in the same network. However, it works with Cisco/Linksys RV042.
View 3 Replies
View Related
May 29, 2012
Region : Ireland
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP :
I have my router updated with the latest firmware and I'm pretty sure all the settings are correct but I'm only getting a max transfer rate of 144Mbps. I know this because I use InSSIDer 3 to analyse my wifi network etc. I stream movies over my network and while DVD quality movies play fine, HD movies tend to freeze and buffer a lot. I have the router's channel width set to 40Mhz, so I know that's not the problem. Strangely, I also use a Netgear wifi extender with the MR3420 and it's max rate is 300Mbps.
View 7 Replies
View Related
Oct 6, 2011
i want to set WRVS4400N Route all traffic through
it function as same as sonicwall Route All
[URL]
View 1 Replies
View Related
Jun 22, 2012
I've got an 877 configured and working just fine as a NATing DSL router, but I'd now like to add an ASA beside it. I've got an extra IP from the ISP so what I'd like to do is bridge the DSL interface to one of the switch ports on the 877 and plug the ASA in there.
I've created a bridge group, put the ATM0.1 in it and then tried to put a switchport in it and get:
FastEthernet1 does not support bridging
So, I created an SVI and put that in the bridge-group and added Fa1 as an access member of that VLAN, but nothing seems to come out the interface to the ASA.
View 5 Replies
View Related
Oct 18, 2012
Can you use a Cisco 3600 to do a P2P bridge? Using the MAP's ethernet port to connect to a remote LAN? On that remote LAN can you have lightweight APs that connect to a controller on the RAP side?
View 13 Replies
View Related
Aug 28, 2012
I'm trying to build a project where I utilize a Cisco 877 as a dumb modem by briding the ATM interface together with an Ethernet interface (VLAN) in this case due L2 switchports.The online documentation for RFC 2684 bridging states that I should be using AAL5SNAP as the encapsulation mechanism however, my ISP requires that I use the AAL5MUX encapsulation as part of the DSL settings. [code]
View 5 Replies
View Related
Jan 24, 2012
I have a piece of hardware (audio device) with Ethernet network access only. I'd like to give it to my users and have them connect via Wifi. But configuring a Wifi bridge for each use is too onerous. I'm looking for a wireless bridge device with a display and keypad that allows the user to scan, select and associate with a wifi router, then bridge the wireless network to ethernet so I can attach my device. Does such an animal exist? Price is not a major factor.
View 5 Replies
View Related
Aug 10, 2011
we have a 1310 connecting two buildings networks.inside each building we have a wireless network (Intermec access points).we are implementing WEP on the Intermec AP's.will the cisco 1310 allow the wep traffic without interference? or would i need to modify the 1310 somehow?
View 2 Replies
View Related
Jul 2, 2011
These questions are only in relation to the above Wireless Router (v6, FW-v1.02 [2010]) :
1. What is an Ethernet Bridge (the basic authoritative definition), and besides gaming, what are they generally used for in a business setting?
2. What are VPN settings in a Router used for, and can a VPN be configured on a remote PC without them?
3. Utilizing bridging, etc., can I utilize my WRT54G as a makeshift Range Expander as long as the primary router doesnt have WEP key requirements? The current WIFI doesnt reach my PC, so I thought I could configure my router midway in hopes of extending the other routers' signal, via some kind of bridging if necessary. Naturally, there would only be a wireless connection between routers.
4. How can I setup a simple Captive Portal on this router?
View 1 Replies
View Related
Jun 13, 2012
I have a DAP-1522 in my den that I am connecting as a bridge to a Netgear WNDR3800 that in turn is connected to a cable modem in my living room. I have multiple PC's connected to the DAP-1522 via the Ethernet Ports. All the Ethernet connected PC's are getting IP addresses from my Netgear WNDR3800 via DHCP and can access the Internet fine. The weird thing is the PC's connected to the DAP-1522 through the Ethernet ports can't see each other - they are isolated from each other. I can see the DAP-1522 hard wired PC's from a laptop connected wirelessly through the Netgear WNDR3800 but the PC's wired to the DAP-1522 can't see each or communicate to each other via IP, though they can communicate to anything else on the Netgear WNDR3800 wireless network or Internet.Only the PC's connected to the DAP-1522 via the Ethernet ports are isolated from each other. Very strange. This is a problem because I have a NAS device I want to connect to the DAP-1522 that will be shared by the PCs in my den. I do software development and want access between the PC's and NAS device at Ethernet Gigabit speed. I am using default configurations for the DAP-1522. It appears that firmware for the bridging function if funky. I am on firmware version 1.41. The hardware release is A1.Not sure if it is an issue with the DAP-1522 or the Netgear WNDR3800.
View 5 Replies
View Related
Jun 4, 2012
Tomorrow 2012-06-06 is ipv6 launch day, what about ipv6 on srp500 series ? On product specification cisco wrote : IPv6 (RFC 6204) ready.
View 10 Replies
View Related
Jan 27, 2010
Is there any IPv6 support planned or in the works for RV082?
View 3 Replies
View Related
Apr 13, 2011
I am trying to bridge internet connection received from my laptop to my desktop with an ethernet cable. Both machines are running win 7.When I try to connect to my local area connection on the desktop most of the time it fails and I'm left with 'Unidentified network' and no internet connection. Sometimes, rarely it does connect properly but I get a notification about there being an IP conflict in the network, but things work as they should.When I diagnose the problem it tells me that "Local Area Connection doesn't have a valid IP configuration"
View 5 Replies
View Related
Feb 14, 2013
I have the DIR-655, Rev. B running 2.07NA firmware, and have a strange problem with my wired clients. I have my primary computer/desktop PC connected via wired connection. I also have several wireless clients (laptop, iPad, iPhones, etc.). All have been performing normally. However, in December I connected a wired weather internet bridge to another ethernet port on the DIR-655.
It functions as it is supposed to, and all other connected devices do as well. But here's the problem - whenever I use the desktop PC (the only other wired connection) to do anything on the internet (mostly just web browsing ... I don't stream media from the internet on it, I don't do torrents....nothing out of the ordinary, and nothing really of high bandwidth), the wired weather bridge cannot communicate with its associated website. This continues as long as I'm using the desktop PC. When I stop using the desktop, the weather bridge resumes normally.
I have researched the weather bridge, and it is simply doing POST transactions (or so I'm told) to the website listening to it. It doesn't wait for acknowledgements or anything...just keeps POSTing updates. I tried reserving an IP for the weather bridge and the desktop, enabling QoS, and prioritizing the weather bridge (100 vs. desktop at 125), but it didn't work. I've tried moving the weather bridge into the DMZ. I'm totally baffled how just using the desktop to browse the internet could completely block the traffic from the weather bridge.
On the weather bridge support site, they suggested that I insure I'm not connected in gigabit speeds from my computer to the router, because in the past that has been known to cause issues on clients not running that speed, but I don't think my desktop is connected in that fashion. According to the settings, it can do 10 or 100, full or half. I have it set to AUTO.
View 3 Replies
View Related
Aug 26, 2011
Protocol 41 with ipv6
View 1 Replies
View Related
Feb 6, 2011
want to know how to format IPv6
View 1 Replies
View Related
Mar 3, 2013
I've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the Ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.The switch port that is connected to the RAP and MAP is configured as the following:
switchport mode trunk
switchport trunk native vlan 2
switchport trunk allowed vlan 10,20,30,40
[code]....
The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.
View 2 Replies
View Related
Jan 25, 2012
My ISP provides IPv6 connectivity in the form of dual stack IPv4/IPv6 with DHCPv6 Prefix Delegation. Using a Cisco IOS-based router I managed to make such a connection by using as a template the Cisco IOS configuration file that my ISP has posted as an example in the following link:
[URL]
The main point on this configuration is a PPPoE connection with:
interface Dialer46
ipv6 address autoconfig default
ipv6 enable
[Code].....
configure this router according the Cisco IOS configuration file I linked on the top in order to have a working IPv6 connection?
View 4 Replies
View Related
Jun 21, 2012
how to add IPv6 support via HE's TunnelBroker to an RV016.
View 0 Replies
View Related
Nov 10, 2010
Is there a new software version that supports full ipv6 for wan and lan? What may be the replacement for rv016 that supports full ipv6 and may have a density of 8-16 10/1000 ports?
View 3 Replies
View Related
Jun 27, 2012
I enabled dual stack on my rv042g router but its not recieving ipv6 information from my isp. My isp is Time Warner in Milwaukee. They assure me that they are ipv6 ready and assume the problem is on my end. All they want to do is have me connect one computer up to my modem. What good is that when I have a network that needs service. The router needs to be working not just one pc. My ipv4 is working perfectly. It is obtaining all information automaticly.
View 3 Replies
View Related
Apr 28, 2013
I have several RV082 routers in production, most of them on IPv4-only access. I want to roll out IPv6 on all these networks and have set up a test environment for this.I did start with a factory-defaulted router with a fixed public IPv4 address. IPv4 network access does work as expected.With the 6to4 option disabled, the RV082's IPv6 routing table contains several entries for local addresses, but not public ones, as expected. When enabling the 6to4 transition function as described in SBKB article #567, three new entries are created: [code]
With the router's diagnostic ping function I can ping the next 6to4 relay on IPv4 (192.88.99.1) and IPv6 (2002:c058:6301::). But I cannot ping that next hop address given as default route (::c058:6301).The RV does advertise routes with the correct 6to4 prefix on the LAN side, and the clients connected to it configure themselves with appropriate addresses. However I was unable to ping any IPv6 both in the 2002::/16 as well as in the 2000::/15 range from any system on the RV's LAN side. When trying to add a static route which routes the 2000:: prefix with prefix length 15 to next hop 2002:c058:6301:: with metric 1, I keep getting the message "Please input IPv6 Address with correct format!"could there something wrong with this default route? How can it be changed? And what is the problem with the route I am trying to add?
View 1 Replies
View Related
Jun 1, 2013
When I attempt to save IPv6 Router Advertisement settings, it fails and displays this cryptic message:
Addtionally many of the settings in this dialog are not in the PDF manual. Seems odd - like this portion of the Router Configuration is broken.
Steve CICSO RV180 FW:1.0.2.6
View 1 Replies
View Related
Feb 27, 2013
I have a few questions regarding IPv6.
Question 1.
I have no idea how to route IPv6. My provider has provided me with a subnet. This subnet is for example 1:1:1::/48
The router of the provider is located at 1:1:1::1 and my router should get 1:1:1::2(Cisco router). Every subnet I want to create must be routed by 1:1:1::2, for example if I want to create 1:1:1:1111::/64 it needs to be routerd by 1:1:1::2
How do I configure this on the RV220w?
Question 2.
I have the possibility to create vlans on the RV220W. I can configure IPv4 addressen per vlan. Only for IPv6 this is not possible.How do I configure this or when will new software be released to configure this?Or do I have to edit the configuration file?
View 2 Replies
View Related
