WRV54G - Server Cannot Send Outgoing Traffic Through Network
Dec 30, 2011
I cannot get my server to send outgoing traffic through my network. I.e. If i try to connect to any of my services i get a very weak connection. Now, i can still CONNECT, i just don't get any data flow. I cant even PING the server internally, it just times out. Now, regardless of whether i use my internal IP/external domain, i get the same issue. I logged onto my computer and tried a speed test the download was normal (around ~20mbit) but the upload times out.
Here is the fun part, if i connect to the server using a switch, everything works fine! Is it my router or some stupid configuration issue? Router is a WRV54G (I hate this thing). Server is running windows 2008 and has a virtual machine.
View 3 Replies
ADVERTISEMENT
Jul 14, 2011
I have got a Cisco router connected to a LAN and to the internet.I was wondering if I could nat https traffic from inside to internet to a local server (Proxy) on a given port for example tcp 8080.
int tunnel0
ip address 192.168.0.1 255.255.255.0
ip nat inside
int fa0/1
des internet connexion
ip address 41.x.x.x.x 255.255.255.248
ip nat outside
ip access-list extended Proxy_Redirect
permit tcp 192.168.0.0 0.0.0.255 any eq 443
View 1 Replies
View Related
Mar 17, 2011
I currently have 90 remote locations that have PIX501's. They are all running 6.3 on them. All of these locations are creating an IPSEC VPN to my ASA 5520 (8.4) at the data center. Web access at the remote locations is currently being handled with ACL thru split tunnels. This is getting increasingly not fun as I have to reach out and touch them one at a time whenever I have to allow more access to the net. Code...
I would like to keep my split tunnel (if possible) for ports 443 and 21. I allow access to "any" on those ports and have no plans to change it.
Can I send port 80 down the VPN tunnel to the Proxy/Web Filter and then return the results to the Remote Client.
View 4 Replies
View Related
Oct 9, 2012
I want to be able to use port 1-80 for all outgoing traffic. I have a VPS outside my home, which can redirect the packets to the prober ports.Is it possible with an application on the computer and VPS? Or is it impossible?
View 1 Replies
View Related
Feb 6, 2012
I have a licensing server. Other computers need to turn on a program, they send a message to the licensing server, and it responds that they have permission to run.Until today the licensing server was plugged into its own ethernet wall socket and configured with a static IP address. Today I put a router into that wall socket and now the server's plugged into the router.The router (WRT-54G) was set to the static IP - and now the internet on its network works. I set all ports to be forwarded to the server's internal IP address - and now my programs can detect and ping it. But now the server won't send back permissions to use licensed software, or even reply with a list of the software which it can license.
View 1 Replies
View Related
Oct 12, 2012
cisco 2651XM router with WIC1 adsl card and NM-16ESW switch
IOS: c2600-ipbasek9-mz.124-23.bin
I use the following config to export traffic from the adsl card to a fasterthernet port so I can look at the adsl traffic in wireshark on a pc:router(config)#ip traffic-export profile my_rite router(conf-rite)#int FastEthernet 0/0 router(conf-rite)#bidirectional router(conf-rite)#mac-address abcd.efgh.ijkl (mac address of PC) router(conf-rite)#exit router(config)#int dialer0 router(config-if)#ip traffic-export apply my_rite this config works and I can see stuff going on in wireshark but it's only one way. This config only shows traffic going out from my adsl card, but no incoming. There is defintely traffic going both ways because everything about my adsl connection is working perfectly. I've tried using a different fastethernet port, even tried exporting to a different pc but all I see is outgoing ie: source is my public ip address but never as destination . I have bidirectional in the config but it still only shows outgoing. I even tried a different IOS (c2600-adventerprisek9-mz.124-15.T8.bin) but still it doesn't show incoming traffic. Could it be my ISP in some way hiding incoming traffic from view?
View 3 Replies
View Related
Jan 29, 2012
we've buyed a WRVS4400N to create a IPSEC VPN tunnel to our client in order to access some applications.
After a while trying to configure the router, we have archieved it and the VPN tunnel is up. We can see the tunnel up from here and from client's side as well.
Our client supposendly have created the tunnel in order to access a list of specific IPs in the range 10.113.x.x, but if we try to access this IPs via telnet whe cannot obtain any response.
Making a tracert, we obtain...
C:UsersHuexxx>tracert 10.113.56.177
Traza a 10.113.56.177 sobre caminos de 30 saltos como máximo.
1 1 ms 1 ms 1 ms 192.168.0.1
2 * * * Tiempo de espera agotado para esta solicitud.
3 * * ^C
... and therefor the client doesn't receive any packet at its firewall.
I've tried to establish a static route for 10.0.0.0 255.0.0.0 to their remote gateway, but I'm unable to add any entry to static routing list... The router tries to do something, but afterall I cannot see the new entry...
What can I do to route the traffic through the tunnel?
View 1 Replies
View Related
Apr 25, 2012
For ASA v8.3 and above we don't need to use nat-controll, traffic from high security interface can go to low security interface without matching NAT statements.So does the ASA automatically NAT s the outgoing traffic to the outside interface by default?
For example
ASA inside int---10.1.1.1
outside int---120.11.1.1
when the inside hosts try to go out they will be NATed to 120.11.1.1 by default on version 8.3 and later.is that right?
View 7 Replies
View Related
Dec 15, 2012
i want to setup mu outlook but my sent items is not sending pop up keeps on saying my outgoing server is not found .
View 1 Replies
View Related
Aug 4, 2012
I am trying to limit the incoming and outgoing traffic on a l2 port to 8mbps for a ip subnet within the nexus 7000. The port is connected to my ISP router which has a bandwidth of 20mbps.Policing won't work on a l2 Port and shaping cannot be applied on a port level. url...I have been reading thru the qos guide for nexus release v6 and have problems understanding the different queues.
View 3 Replies
View Related
Mar 4, 2013
We have a Cisco ASA 5520 and im looking for a way to monitor largest outgoing and incoming traffic per ip in real time so to know which of my internal computers are using the most of our Internet Line. Is there a way to this through ADSM ? We use version 6.3.
View 1 Replies
View Related
Mar 19, 2013
how I could possibly get all my e-mails of which I send my clients through my outlook to be registered on my Home-outlook, Office-Outlook and my mobile-outlook? like on the server? something similar to when you open yahoo or G-mail from any given location you can view your sent Items,inbox etc.
View 4 Replies
View Related
May 7, 2013
One of my customers uses Comcast email and all of a sudden couldn't send messages the other day, telling me it was giving her an error. She said that she reset her router, and the email started working again.When I finally got over there to check it out, the email had started experiencing problems again. The error she was having was Error 550: Message Rejected (when trying to send email). There didn't appear to be any issues with her internet connection, and she wasn't having issues connecting to the email server, it was simply rejecting her messages.
I told her that she would have to contact Comcast, as there was really nothing I could do to fix their email server returning an error. She wasn't too happy, and remained convinced that her router had something to do with it. It's a Netgear WNDR3700 or WNDR3800 that I setup for her last year, it's a fine router.Has anyone ever had a Comcast email server randomly start rejecting messages? I noticed that her outgoing email was set to use port 587 which seems like a nonstandard port and also no authentication, but I have no idea what the Comcast email settings are supposed to be.
View 2 Replies
View Related
Aug 23, 2011
We have Cisco ASA 5505 with ASDM 5.2 We have one Proxy server in our Local Lab and pointed to Hosted service(Simple Signal)issue is, When our proxy server send register to hosted server, ASA change private IP and post with outside IP and src port as 1063 every time.
Here is debug log on real time monitoring.
Aug 24 2011 05:21:19 302015 203.xxx.xxx.226 192.168.1.51 Built outbound UDP connection 3774 for outside:203.xxx.xxx.226/5060 (203.xxx.xxx.226/5060) to inside:192.168.1.51/27014 (99.119.161.107/1142)
Aug 24 2011 05:21:19 607001 203.xxx.xxx.226 Pre- allocate SIP Via UDP secondary channel for inside:192.168.1.51/27014 to outside:203.xxx.xxx.226 from REGISTER message
Aug 24 2011 05:21:19 710005 203.xxx.xxx.226 99.xxx.xxx.107 UDP request discarded from 203.xxx.xxx.226/5060 to outside:99.xxx.xxx.107/1063
Here 99.xxx.xxx.107 is Our ASA Outside IP address 203.xxx.xxx.226 is Hosted server IP address. My ASA config is attached.
View 2 Replies
View Related
Feb 17, 2013
I found this guide in order to send all traffic from RV042 branch office to the RV082 in the central office: [URL]
But that guide is for v2 hardware. I tried and did not work, so I wonder if there is newer info for v3 hardware (firmware v4.2)
I have a RV042 in a brach office connected via working VPN Tunnel to a RV082 central office. I want to route all traffic from the brach office to the RV082 in the central office.
View 2 Replies
View Related
Apr 28, 2011
I am supporting a small call center of all Win7 machines. There is no server in house as everything is web based. Anyway, we want to find the bandwidth hogs and programs that I am used to using require servers for monitoring web traffic.
Are there any devices or software that is not a fortune that can give details on bandwidth usage?
View 1 Replies
View Related
Feb 21, 2013
’m somewhat new to Cisco routers this is my first attempt at getting one to work. I work in an environment with multiple locations, most are using the Cisco Model: 2911/K9 or the Model: 2921/K9 routers running IOS Version 15.0.We just added a new small office and all I had in the way of a router was a Cisco C1841-IPBASE-M router, running IOS Version 12.4.When setting up the C1841 I kept the configuration pretty much the same as the others allowing for the differences in the OS. I can remote into the 0/0 (outside port) from over the network, I can ping to that port without fail, but I can’t send or receive traffic from the 0/1 (inside port).
View 1 Replies
View Related
Oct 9, 2011
below is my sanitized ASA 5510 config. got an IPv6 T1 from at&t and im unable to pass any traffic from my LAN clients out.
:
ASA Version 8.2(2)
!
enable password PoBmYYxuAzCciKRA encrypted
[Code].....
View 6 Replies
View Related
May 22, 2011
I have a 2003 standard machine with networking issues. the nic shows that it is connected and it received the correct DHCP ip from the router but i can't ping the router or any other ip on the network.i ran a TCP/IP fix, Winstock Fix, LSP Fix, checked the services that starts up, checked the startup programs, turned the firewall off, checked in advanced settings on the nic if the correct order is there. the funny thing is that in safe mode with networking it works like a charm but not when i boot in to windows normally.If i ping the router it just shows destination host unreachable.
View 3 Replies
View Related
Aug 22, 2011
I have a RV220W (running fw version 1.0.2.4) that i am trying to configure for a client. They are set up on Comcast with 13 available IP's. I should note that this netowrk is now currently running without issue using a Cisco Pix 506e. Unfortunately, the Pix is almost impossible to configure using the GUI now as I have to load a 4-year old version of Java now just to get the PDM to load. But I digress.I've set up the RV using the identical settings as the Pix on bth the LAN and WAN side. When I do, computers on the LAN side can all reach the Internet ok. However, once I enable one-to-one NAT for an internal server, that machine can't send or receive ANY traffic to the WAN side. I've even tried setting access rules enabling ANY traffic in both directions, and that has no effect. Either I'm missing something, or this is just one more bug in this product.
Even though it was a bit of a step down going from the Pix to the RV220W, it was done for the ease of setting up VPN's as I was ready to purchase a second one for a new satellite office opening in a few weeks. It looks like we will be switching vendors on the router side as my faith in Cisco is waning at this point.
View 1 Replies
View Related
Sep 26, 2011
I have some specific traffic that I am attempting to pull off of VLAN 310 at the router, apply a route-map that sends this specific traffic back down to the switch on VLAN 55 (and the private address) and once it hits the switch apply a route-map on that VLAN 55 interface directing the same traffic over to the 72.x.x.9 address which goes through a FAP box back up to the router on another interface.
I have attached the config information, I know this isnt the best practice way to do this however right now this is how I have to do this.When runing a trace from the net traffic stops at .2 and when running a trace from my test /30 it stops at .2 as well. I am not sure what to do at this point
[code]...
View 6 Replies
View Related
Jun 8, 2011
I have installed CSC-SSM-10 on cisco ASA 5520.I am facing two problems
1 : When I send traffic from ASA to SSM module then internet connection becomes slow and sometimes internet session disconnected.
2. When I try to manual update then following erros shows please see attachment .
View 6 Replies
View Related
Apr 18, 2013
I have a an ASA 5520 connected to a Layer 3 (3750) switch (Inside) and a connection to a 2960 switch (Outside) to get to the internet. . I have created vlan interfaces on the 3750 switch and enabled ip routing on the switch to enable the vlans to communicate with each other.
Vlan Interfaces on the switch:
Vlan 100 172.17.1
Vlan 200 172.18.1
Vlan 300 192.168.3.1
I want the devices connected to the 3 vlans to be able to pass through the firewall and get out to the internet.I have connected the ASA to the 3750 by routed interfaces (10.10.10.1) --------- (10.10.10.2) and they are able to ping each other.I have also put a default route on the 3750 sending all traffic from the switch to the ASA inside interface (10.10.10.1)The issue that i am having is that the ASA also connects to a 2960 which has a connection to the Internet, and they are handing off an ethernet connection from the 2960 that sits in VLAN 55 (Vlan 55 is the Internet accessible vlan).How do I configure my ASA to send all traffic from my (3) vlans to the interfaces that connects to the 2960 switch?
View 21 Replies
View Related
Sep 6, 2011
Whose address I would put in "Send to LAN server" within firewall rules for inbound services.
View 4 Replies
View Related
Aug 24, 2011
net send command not available on server 2008
View 1 Replies
View Related
Aug 14, 2012
I have a server with two adapters: 192.168.1.200 and 10.99.1.200, 10.99.1.200 connects to a cisco router 10.99.1.254 (which I have no access to). This connects via WAN to another network to transfer files to another company. 192.168.1.200 is connected to our local LAN. I have a service that uses FTP to get and send files to a server through 10.99.1.200. I recently had to switch our IP scheme from 10.99 to 192.168 and since then haven't been able to send files to the ftp server. My question is, would a router solve my problem? If so, would I; remove the 10.99 adapter, connect 192.168 to the router, connect the router to the switch, connect the 10.99 gateway to the new router (and update any appropriate routing tables on the server)? The service appears to have issues with using a dual homed server and updating it isn't going to happen anytime soon.
View 3 Replies
View Related
Apr 21, 2011
Kerio Control with AD, DNS."Failed to send DNS query to server 127.0.0.1: 10049".
View 1 Replies
View Related
Oct 26, 2009
Wondering if it's possible to send a VSA from my radius server to my ASA-5505 that will instruct the ASA to use one of several split tunnel lists I have created, based on the user name supplied in the Radius request.For example, I can send a VSA of "ip:inacl#1=permit ..." and the ASA will dynamically create an access-list for that user.Is there a similar VSA for split tunnel?
View 8 Replies
View Related
May 8, 2012
I have one server-A(windows 2008) installed one application called"host front" which gives athentication to connect Linux(mainframe console)server(SERVER B). These 2 servers are bihind the firewall.If one internal user who has the athentication to logine server-B ,tried to login server A,will get the" username and password"screen and once they enter the username and password ,will get the server-B screen.But if somebody try to connet via MPLS(we need to test MPLS site customers) from outside via ASA 5540 ,to server-A will get the "username password" screen and once enter the credentials,after 1 minitue will get error"http server faild to send datas to the server" and will not move to server -B screen.Where do you think is the problem?
View 3 Replies
View Related
Mar 9, 2013
I'm having an issue with the syslog.
My configuration is:
LAN A (RV042)<-> GW to GW tunnel <-> (RV082) LAN B
On LAN A, I got a NAS with a syslog server. On the RV042, I've set the parameters for the syslog server, and it's working fine. On the RV082, I've set the same parameters and noting is happening.
As troubleshooting, I've done the following:
-On the RV082, I can ping the NAS without problems.
-On the RV082, I've set my computer IP adress as syslog server IP and with packet analyser, I not seing any UDP packets.
View 6 Replies
View Related
Sep 26, 2012
We are still using some old WRV54G wireless VPN routers for work. Can we get new vpn software that will work with these routers? The quickvpn client software we have no longer works after we last updated the firmware. How can we set up vpn connections using tunneling?
View 1 Replies
View Related
Aug 23, 2012
I have a problem with that the ACE20 (A2(3.2)) does send the connections to a backup real server in the serverfarm. I will how to troubleshoot in this case ? This is serverfarm configuration.
serverfarm host fix-http
failaction purge
probe PROBE-TCP-80
rserver fix11
inservice standby
rserver fix12
View 2 Replies
View Related
Feb 16, 2010
I recently purchased the WET610N Wireless Bridge to use with my Samsung BD-P1590 Blu-Ray Player. The player has a few built in apps that include Netflix, Bockbuster, Pandora and YouTube. I successfully setup the bridge and hooked it up to the blu-ray player. It wasn't that hard. All the internet apps on the player work fine except Netflix. The first time I use the netfix app, it is supposed to give me a code that I use to register the device with netflix. However, I get a message that Netflix is temporarily unavailable. I have called netflix and they assure me that this is not the case and that it is most likely my wireless setup. The troubleshooting on Samsungs website points to the same thing. With that said, I disconnected the player from the wireless bridge and wired it directly to my router. Netflix works just fine then. Below is a list of things I have attempted:Disable the firewall on the router to see if it was blocking the app. (had the same results)Checked my firmware on all my devices (they are all current)Powered down all my devices and started them up back up starting with my DSL modem and ending with he blu-ray player (same results)Configured the bridge and player to use a static IP vs using the IPs automatically assigned by the router. (same results)Disabled aggregation on all WMM categories. I don't think the WRV54G router supports aggregation,, so I though this might cause a conflict with my setup. (same results)Enabled the broadcasting of SSID (same results)Chatted with linksys support. They basically checked to see if I had the latest firmware and that the bridge was working. They then recommended that I exchange the bridge for a new one. (I have not exchanged it for a new one yet, just because I am not convinced that there isn't something else wrong with my setup)My Configuration
DSL Modem --> WRV54G Linksys Wireless Router --> WET54G Wirelss Bredge --> Samsung BD-P1590 Blu-Ray Player
Router is broadcasting in Wireless G only on channel 1
Using WAP-PSK encryption
I am not sure if the problem lies with the routewr or the bridge. I am hoping someone out there can confirm that the WET610N truly does work whne using it with a BD-P1590 blu-ray player. This would lead me to believe that there is something wrong with my configuration or with using it combination with my older router. I would like to note also, that I have had one instance where BD Live didn't work. However, it has worked on other disks.
View 5 Replies
View Related
