Wondering if it's possible to send a VSA from my radius server to my ASA-5505 that will instruct the ASA to use one of several split tunnel lists I have created, based on the user name supplied in the Radius request.For example, I can send a VSA of "ip:inacl#1=permit ..." and the ASA will dynamically create an access-list for that user.Is there a similar VSA for split tunnel?
View 8 RepliesI've got a pair of Cisco ACS 4.2 servers running on our corporate LAN. Currently they are doing TACACS+ for the network gear, and wireless authentications for internal users.
We have contracted with an external web site for an application - They can run RADIUS from their site to our LAN for the user authentications. How can I best do this?
1. NAT the traffic on my ASA firewalls to the internal servers, send the RADIUS traffic to/from the external site?
2. Is this secure?
3. Should I have a RADIUS server in the DMZ instead?
4. Any issues with doing this on ACS 4.2?
We have Cisco ASA 5505 with ASDM 5.2 We have one Proxy server in our Local Lab and pointed to Hosted service(Simple Signal)issue is, When our proxy server send register to hosted server, ASA change private IP and post with outside IP and src port as 1063 every time.
Here is debug log on real time monitoring.
Aug 24 2011 05:21:19 302015 203.xxx.xxx.226 192.168.1.51 Built outbound UDP connection 3774 for outside:203.xxx.xxx.226/5060 (203.xxx.xxx.226/5060) to inside:192.168.1.51/27014 (99.119.161.107/1142)
Aug 24 2011 05:21:19 607001 203.xxx.xxx.226 Pre- allocate SIP Via UDP secondary channel for inside:192.168.1.51/27014 to outside:203.xxx.xxx.226 from REGISTER message
Aug 24 2011 05:21:19 710005 203.xxx.xxx.226 99.xxx.xxx.107 UDP request discarded from 203.xxx.xxx.226/5060 to outside:99.xxx.xxx.107/1063
Here 99.xxx.xxx.107 is Our ASA Outside IP address 203.xxx.xxx.226 is Hosted server IP address. My ASA config is attached.
getting a Cisco WLC to work with MS NPS server? We've done it before albeit with differnt code versions.
I have a Cisco 5508 WLC running 7.0.116.0 code hosting a WLAN configured for WPA2 with 802.1x for authentication. I have two Windows NPS servers configured as the RADIUS servers for EAP-TLS authentication. Via debug info on the WLC I can see the 802.1x handshake take place with the wireless client and the WLC as well as a successful transmission of an Authentication Packet from the WLC to one of the RADIUS servers. However on the WLC I see repeated RADIUS server x.x.x.x:1812 deactivated in global list and on the NPS server I'm seeing event log errors indicating "The Network Policy Server discarded the request for a user" along with the pertinent auth request info that I would expect the NPS server to receive from the WLC. Based on the WLC debug info I'm never actually getting to the EAP-TLS certificate authentication part. It seems the NPS servers don't like the format of the initial RADIUS authentication request coming from the WLC and so don't respond whcih in turn casues to WLC to switch to the other NPS server which produces the same issue.
Is there any way to set up our ISE to provide Radius instead of acting as Radius Proxy? In our Company we use ACS 4.2 to provide AAA via Tacacs+ and this works proper with all our Cisco-Switches. Now we are testing the ISE 1.1.1 as NAC-Solution.
I know how to set up the ISE as 'Radius Proxy', configuring the Sequences and Policies, but till now we are using only Tacacs+ for AAA. The current version of ISE does not support Tacacs+ and I don't want to set up a Radius-enviroment in ACS if not necessary. Somewhere ( I think the specs) I read, the ISE is a merge of ACS and NAC. So in my Opinion there should be a way to provide AAA via Radius on the ISE without ACS and without 'Radius Proxy'.
After we have installed patch 5 on several ACS 5.2 server they aren't able anymore to write their backups to the sftp servers. I tried to search on the bug tool kit, but it seems to be broken when searching for the keyword "sftp". It's the same when I try to do a "copy logs" with sftp as destination.running a debug I can see,
acs/admin# copy logs sftp://10.1.115.11/,Collecting logs...,Username: backupuser,Password: ,6 [16376]: transfer: cars_xfer.c[301] [admin]: sftp copy out of /var/tmp/ADElogs.tar.gz requested,6 [16376]: transfer: cars_xfer_util.c[412] [admin]: resolved server to 10.1.115.11,7 [16383]: transfer: sftp_copy.c[75] [daemon]: Executing SFTP command: /usr/bin/scp -o StrictHostKeyChecking=no /var/tmp/ADElogs.tabackupuser@10.1.115.11://ADElogs.tar.gz,% Error: Transfer failed3 [16376]: transfer: sftp_copy.c[230] [admin]: sftp_copy ERROR: command execution failed,3 [16376]: copy: cm_copy.c[1226] [admin]: Logs archive transfer to url sftp://10.1.115.11/ failed retcode=-306,acs/admin#
I was just wondering if it was possible to turn a cisco 887 Router into a RADIUS Server. What i wanted to do was setup my wireless AP to authenticate using RADIUS, but didn't want to setup another server for the purpose.
View 1 Replies View RelatedI am using CiscoSecure ACS v4.2 appliance, in there any way that RADIUS logs upload to FTP server because it has limitation to store RADIUS logs.
View 15 Replies View RelatedI'm trying to configure ACS 5.4 as radius server for network access (PPP connections).In monitoring and reports the users have green color , but the clients cannot send data. Auth method is CHAP/MD5.
Allowed protocols are set to CHAP and PAP only.
I can authenticate between our MDS 9216i switch and RSA radius server but my role does not come across. The logged in user is a network-operator not admin. In the AV Pair i have defined shell:role*network-admin but it doesnt seem to come across
View 4 Replies View RelatedI have a couple of ACS 5.2 configured as active and backup and I am doing dot 1x authentication using these servers . I have configured the switch with the bellow configuration.
radius-server host 10.0.10.15 auth-port 1645 acct-port 1646
radius-server host 10.0.10.16 auth-port 1645 acct-port 1646
radius-server key 7 aaaaaaaaaaaaaa
please help to understand what will happen in switch
1) in case of primary failure
2)in case if primary returns alive .
I am trying to install Radius server for a cisco 2801 router. I am not able to configure it properly.
View 2 Replies View RelatedCan I use AAA Radius on a ASA 5505 to block outgoing user access by user name in a group?
View 2 Replies View RelatedI tried to authenticate and authorized Nokia/checkpoint Nortel/AD3 and Nortel 5510 platform using an 4.1 for windows ACS. the ACCESS-REQUEST is well processed bi the radius server wich send ACCESS-ACCEPT to the AAA Client (ie NORTEL or NOKIA), but i'have got privilege access denied on the Client side. RADIUS IETF Dictionnary is used for every device. all others Cisco Devices authenticate and are well authorized.
View 3 Replies View RelatedWe have several ASA 5510 firewalls which are being used as VPN gateways.RSA SecurID is the authentication mechanism using native SDI connectivity. No ACS server is being used.Is it possible to assign user Group and other attributes (such as ACL), using the SecurID RADIUS server? I know this is what the Cisco ACS is for, but is it possible using the RSA RADIUS server itself?
View 11 Replies View RelatedI am configuring TACACS Authentication on Cisco 3550 switch .It has Version 12.2(25)SEA IOS image. A strange thing is happening, whenver I am enabling AAA new-model on this switch, and then after enabling I see ruuning-config . It shows me this
tacacs-server host x.x.x.x
tacacs-server host x.x.x.x
no tacacs-server directed-request
tacacs-server key 7 xxxxxx
radius-server source-ports 1645-1646
* included here to hide the specific information I dint specified any RADIUS server , why it is showing me radius-server source-ports 1645-1646 after enabling AAA New-Model As soon as i give "no aaa new-model", this parameter also vanishes. I think this is the only reason I am not able to do tacacs authentication.
We have configured following commands on switch to fallback to local Vlan if both radius server (policy persona's) is found dead. For test purpose we shutdown both servers (policy persona's) but fallback didn't work. We have 3750 switch running image 12.2(55)SE6 having following configuration.We do not know whether we configured switch in proper way or do we need to modify it. [code]
View 5 Replies View RelatedI have 2 subnets bought from my provider 194.102.98.128/27 and 194.102.98.160/27.
From my provider a have the following setup:
IP Address: 86.120.151.66
Netmask: 255.255.255.128
Gateway: 86.120.151.1
DNS (1): 213.154.124.1
DNS (2): 193.231.252.1
My IPs are static routed by my provider thought 86.120.151.66 .
On the firewall I have the following set-up:
Outside Interface: 86.120.151.66/25 security level 0
DMZ interface: 194.102.98.129/27 security level 50
Inside Interface: 194.102.98.161/27 security level 100
0.0.0.0 0.0.0.0 [1/0] via 86.120.151.1, outside
Everything works perfectly except when I try to sent an email. The email gets sent (eventually), but afert a long waiting time, 45-60 sec. The connection is opened instally to the server but then just hangs there for 40-50 sec. The problem is that a have an aplication on a server that has to send confirmation emails, and that aplication is limited to a 30 sec timeout for conecting to the mail server, much less then the 45-60 sec that I have now. The mail server is hosted by a data center, it is not in my networks (location).
I have tried deleting the ESMTP inspection, that doesn't work. Pinging my mail server rezults in a average time of 20 ms. And when a do a tracert the hight value in a hop doesn't usually pass 80 ms, the average is 20-25 ms.
The problem is ONLY when sending emails. Everything else works perfect, including receiving emails from the same server.
My running config is:
hostname ASA-Adisys
domain-name Intern.ro
enable password 0./39zRW9yhKK/bO encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
Whose address I would put in "Send to LAN server" within firewall rules for inbound services.
View 4 Replies View Relatedhow can I configure ACS 5.2 to send syslog messages to CS-MARS?
View 3 Replies View RelatedI am currently useing ACS 5.2 and have no problem using Tacacs+ with AD access.
But with Radius it seems I can only get the Local identity store to work, need to do something special to get Radius to work with active directory with Cisco ACS?
net send command not available on server 2008
View 1 Replies View RelatedI have a server with two adapters: 192.168.1.200 and 10.99.1.200, 10.99.1.200 connects to a cisco router 10.99.1.254 (which I have no access to). This connects via WAN to another network to transfer files to another company. 192.168.1.200 is connected to our local LAN. I have a service that uses FTP to get and send files to a server through 10.99.1.200. I recently had to switch our IP scheme from 10.99 to 192.168 and since then haven't been able to send files to the ftp server. My question is, would a router solve my problem? If so, would I; remove the 10.99 adapter, connect 192.168 to the router, connect the router to the switch, connect the 10.99 gateway to the new router (and update any appropriate routing tables on the server)? The service appears to have issues with using a dual homed server and updating it isn't going to happen anytime soon.
View 3 Replies View RelatedDevice: 3841
IOS: 15.1(4)M2 ADVSecurity
Commands: AAA Authorization
Commands take approximately 8 seconds to process when required to authorize with ACS. The show run command will take 8 seconds to process then output is displayed.Packet sniff indicates that it takes 8 seconds for the router to send the initial TCP SYN SEQ packet to ACS. Login to device has no delay.
Using Cisco ASA I want the ssl clientless vpn users to be authenticated through a local Radius-Server. but it does not work, and on asa while i want to see (Debug Radius) output, there is no debuging msgs displayed. When i try to test the user which i have created on the ACS-Server 4.2, the test gets successful. where i have made a mistake in my configuration ?
View 2 Replies View RelatedI have been trying to get our IPS (ASA-SSM-10 and 4260) to authenticate with Cisco Radius ACS 5.2 and they are not working. However, I was able to get them working with Microsoft Radius. Below is the logs from the IPS:
evStatus: eventId=1321566464942057375 vendor=Cisco originator: hostId: NACAIRVIDLAB1 appName: authentication appInstanceId: 350 time: 2011/11/23 17:50:38 2011/11/23 09:50:38 GMT-08:00 controlTransaction:
[Code].....
I need to configure RADIUS VSA configuration for a my alvarion device. Following are the attributes that need to be configured.
- Packet Data Flow ID (ID 1, integer16)
- Direction (ID 4, integer8)
- Transport Type (ID 6, integer8)
- UplinkQoSID (ID 7, integer8)
- DownlinkQoSID (ID 8, integer8)
[code]....
I was able to configure the first 6 attributes, how can I add the Sub - TLV's ClassifiedID, Priority, VLAN-ID and Classifier Direction which come under Classifier. Don't see any option for that in ACS 5.x
We have 2 ACS 4.2.1 servers in Windows 2003 with SP2 installed. We have updated the first ACS to the latest patches for Windows. After that we started having problems. CSRadius either stops by itself or when some time passes we get the following error in Failed attempts "Unknown error". When we restart the ACS services by the GUI, it resumes until the next time it stops.Do you happen to know if we have any bugs related to Windows patches?
View 3 Replies View RelatedI am trying to configure AAA authentication and authorization with Cisco 3725 (IOS 12.4(17)) for 802.1x and ACS 4.2 with VLAN assignment to my Windows XP client. (trying to assign VLAN 100 in my scenario).When user connects to the Router, it passes the authentication process (EAP-MD5). In my debug i see that Router recieves the Radius Attributes BUT does not apply anything!My running config:
Building configuration...
Current configuration : 1736 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[code]......
As a result the vlan-switch data based does not change.
I have a questión about radius authenticaction with AD, when I log in into the network with user in AD and I make a mistake in password my radius authenticaction event in ACS 5.2 dont show me this logg. only show the authentication succeeded but dont show me the authentication failed. Maybe i must to enable same service to show the authentiaction failed. The Voice authetication works fine..
This is the confg in the port of the switch:
interface FastEthernet0/12 switchport mode access switchport access vlan 2 switchport voice vlan 10 authentication port-control auto authentication host-mode multi-domain authentication violation protect authentication event fail action authorize vlan 11 authentication event fail retry 2 action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication periodic authentication timer reauthenticate 60 mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfast end
Vlan 2: DATA
Vlan 10: VOICE
Vlan 11: GUEST
I have the next config of radius authentication:
aaa new-model
aaa authentication login default group radius local
aaa authorization exec default group radius local
aaa session-id common
ip radius source-interface Vlan31 vrf LEGACY
[Code] .....
I want to add Radius attribute to Rad ware devices , so I will have the option to grant "read only" permission to users. as I understand I need to add VSA for the "read only" permission, or configure specific "Service-Type value 255"
in the following picture you can see the required information from Rad ware:
I am using the Self RADIUS server in my Cisco ACS SE 4.2 appliance S. I have an AAA client C that interacts with S by means of the RADIUS protocol. This works fine, in that S correctly carries out authentication chores on username/password (PAP and CHAP) pairs received from C, sending back to C the corresponding Access-Accept packet when the authentication succeeds, or Access-Reject when it doesn't.
I have been able to import a set of three VSAs into S. Each of those attributes is of string type. I then configured in S a single user U with password P so that, whenever a U/P pair received in S from C is authenticated by S, S should send back to C, in the Access-Accept packet, the three attributes with the following values: [code]
With this setup, when an authentication is successfully completed by S, C receives 53 bytes worth of data from S every time. I am attaching a typical example, already disassembled. I have disguised the actual vendor ID, for legal reasons, but the rest is exactly as it was when received in C.
According to the disassembly, what we got is an Access-Accept packet, as expected. Its length is 53 bytes - again as expected, for this is the only packet that C has received from S here. However, the packet is incomplete, for attribute #3 is missing its value field.
Looking into the whole packet in more detail, it can be seen that while the wire format for the first attribute, namely, Frame-IP-Address, is correctly constructed, the remaining are not. For example, the sequence of bytes corresponding to the attribute #1 reads 1a 09 00 00 xx xx 2c 61 62 63. I believe that this is incorrect; it should be 1a 0a 00 00 xx xx 2c 61 62 63, for the wire format for this attribute consists of 10, not 9, bytes. I tried a few variations on the values for the attributes, and the results are always substantially the same, in that the wire formats for these attributes are always incorrect.
This all probably implies I have done something wrong when importing the VSAs into S, and/or when configuring things on S. I am therefore attaching the csv files I used to import my VSAs into S; as before, names and vendor ID are disguised, but their lengths are exactly the same as in the undisguised file. I used two csv files: One to import the vendor ID, and the other to import the VSAs under that vendor ID. As for user U, in S's administration GUI I clicked on User Setup and selected user U, moved to the bottom of the screen, where the attributes for this particular vendor were present,introduced the values for each attribute mentioned above, and made sure that button in front of each attribute was ticked.