I have a sa520w router I configured w a vlan for the wireless and port 2. Now I would like the switch to handle both traffic from the default lan and the vlan. I tried creating a vlan on ports 28 and 10 but I cant get it to work. I have my other lan on port 27. Ive read something about switch layers? not sure. so I want port 10 to route to the vlan and other ports go to the default lan.
View 19 RepliesThere are 5 VLAN's and all can communicate through all the different subnets, but VLAN5 can not communicate to the RVS 4000.
VLAN Smart Port set to switch and router - this is not working What Smart Port configuration should be set up to talk to the LAN port on a RVS4000?
VPN is set up and connected, but when trying to connect to the client can not connect to remote networks.
I am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
View 3 Replies View RelatedI have a Cisco SA520W router and needs to set up VPN. Du to major problems with the SSL VPN Client and windows 7, I had to let it go and try a different approach.
That was the QuickVPN client, but as it turs out, it simply impossible from reading the user manual to understand just how I have to set thing up. For instance, the VPN Wizard tells you to enter a preshared key. But in the QuickVPN Client, where do I enter the key?
And shall the "Enable Cisco VPN Client" be ticket off, I assumed yes, but seriously it is impossible to know.
Then in the VPN Wizard again, in the Remote & Local WAN Adress, what shall use FQDN or IP Address. The if FQDN, what shall a enter, the domain name for the router, whats the point in that? The domain name of the VPN Client, seriously, what's the point in that? I would assume that 99% of the VPN Client does NOT have a domain name. Then, if IP address, am I supposed to know the IP address of the client? Same with the "Secure Connection Remote Accessibility", what am I supposed to enter. The IP address which the Quick VPN Client network adapter shall have?
Need to boost signal coverage on an SA520W (even though it is very good, building floor is too clutterd and too darn big.Even using a 2nd unit to extend things may not get it all done; However, searching the site tells me there is an external aerial (one of...) in the SMB range, and it uses "N" style connectors. Looking at the specs on the SA520W, it makes no mention of what sort of connectors those are (Happy to admit I am not a cable guy... well not co-ax anynore at least!).
View 0 Replies View RelatedWe've got an SA520W that's performing nicely, but we need to extend our wireless coverage to a new area of the building (we can get a network cable there). What would be our best option? Just a second SA520W, or are there are APs we should look at?
View 7 Replies View RelatedI have an SA520W firewall, and am implementing a new AP541N. On the SA I am using port 4 to connect the AP. Trunking is on with Vlan 1 and 25. Connecting the AP I am able to use VLAN1, however when I assign a new VAP using Vlan 25, I only receive IP addresses for VLAN1.
View 1 Replies View RelatedAny AP that would be able to wrielessly repeat traffic to my SA520W (so that the AP has no ehternet wiring at all). First off, there is no WDS option anywhere in the SA520W, so there is no method for which to simply create a WDS link between the two devices. Yet the Factory Default Settings table in the SA520W Admin guide indicates there should be (search on WDS in the PDF to find this). both at the lack of integration of these Small Business Pro devices, and moreso at the fact that I was told that these two would be compatible for wireless-only repeating. I've been messing around for hours trying to get something to happen. Maybe I'm just missing something obvious as this is my first time trying to get an AP to talk wireless-only to a wireless capable internet gateway device (the SA520W).
View 4 Replies View Relatedjust wanted to know if the SA520W can wirelessly bridge (Workgroup bridge, WDS, etc -don't care which) to either an AP541N or AP1252... using WPA2-PSK
the 2 seperate examples would be
Internet --->SA520W --(Wireless 30 feet) --->AP541N -->ESW-540-24P-K9
internet --->Sa520W --(Wireless 30 feet)----> AP1252 -->ESW-540-24P-K9
internet --->AP1252 ---(Wireless 30 feet) ---->SA520W-->ESW-540-24P-K9
in other words do you just go into the config of the SA520W ... enter in an existing SSID name and the WPA2-PSK password and it joins that wireless network. lastly does the SA520W support POE to the switch above or only the AP541N
We have a Windows server based network (15 wired computers) and four wireless devices (more to come)We are using a CISCO SA520W appliance in the main building as the perimeter Internet gateway / firewall / wireless access. It all works well.We have a second building too far away for wireless devices to reach the SA520W radio in the main building.The second building is connected via fiber to the main building (switch to switch). Several wired computers are connected to the switch in the second building.We want to provide seamless wireless connectivity as wireless device users move between buildings.
We thought to mount and connect another simple B/G capable wireless access point, via ethernet wire, to the switch in the second building. But we're not sure of the best CISCO/Linksys model to choose for this. The choice should work well with the SA520W configuration and be relatively simple to configure in that environment.We're also unsure of the steps to configure a seamless wireless experience for the roving wireless device users.
We have received from a customer of us an WRT54GL box configured with a Coova software. This Wifi router was supposed to be a Wifi hotspot, but was not configured by us. This box is able, on startup, to get an IP by DHCP, to touch a remote Radius server, and so on (we "tcpdump" the Internet traffic, and we saw DNS requests, radius requests, ...)...
But, we are unable to connect to this box,by SSH or by HTTP, either by plug-in PC to the Internet RJ45 or the LAN RJ45. It has no IP as 192.168.1.1. Instead, it was configured to have 192.168.1.1 as gateway.
Of course, we have no doc on previous install, but only the admin/root password for SSH.We are afraid to lose the config (coova, ...) if we perform a hard reset.What is the best way for connecting on this box ?
I have a WRT54G2 with the most recent firmware upgrade (which brings issue one - there hasn't been a firmware upgrade released since mid 2009?) and am trying to connect to a VPN for work. The connection fails and I have gotten error messages indicating the issue is the router is not configured to allow GRE protocol.
View 1 Replies View RelatedI just noticed that i have port 10080 open on my router (wrt160nv3). Port forwarding is not configured and web administrative access is only allowed through https (443). DDNS is also disabled, I was wondering why this port is open.
View 9 Replies View RelatedI call century link because my router was not connecting at the proper speed of 7 mbps. That problem was easily remedied over the phone but the lady said she could see several devices connected. This lost me a bit because I have a double router configuration. The Action tech PK5000 i turned into nothing more that an internet modem. I disabled the DHCP and configured my Linksys E1200 for all the internal DHCP so there is only one cable going to the PK5000. I should technically speaking look like one user on there network with natural protection from the second router.
View 5 Replies View RelatedI have a Cisco E4200 with a Thecus NAS behind it. I configured port forwarding on port 80, 1080 and 4433 to access the NAS. However it's not working. Also tried to place the NAS in DMZ, but also I cannot connect it from outside my network. Inside my network, there is no problem.I also connected the NAS directly to the internet, and then I can access it from outside my network.I already tried a factory reset, disabled UPnP and IPv6, but nothing seems to work. I also replaced the router with a Cisco E3200, but it makes no difference.
View 9 Replies View RelatedWe are using a SA520W as our primary router and have a fiber connection attached to the default WAN interface. We would like to improve our uptime using a secondary internet connection on the optional WAN interface.
We have bought a dovado tiny 4g router for this other connection. It acts as a dhcp server but the Cisco router does not get an IP from the dovado router. The router works as expected when connected to a normal computer. But somehow the cisco router doesnt get an IP.
I have also tried to set a static IP for the Cisco router but that didn't work either. The dovado router is setup do deliver ip in the range 192.168.0.2-254
I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies View RelatedI purchased a SA520W for my company, and i have some probles for configuring firewall. I want to deny access to facebook, youtube and twitter but not for 4 hosts which needs this websites for work. I tried to configure content filtering > blocking URLs but with this solution, I deny acces for all users, So, I tried to make IP v4 rules :
The 4 hosts who may access to these websites are 192.168.50.124 to 127
Example :
FROM Zone : LAN
TO : WAN
Service : Any
Action: block always
Source hosts : 192.168.50.32 to 192.168.50.123
destination hosts : 66.220.158.11 (one of the facebook's ip)
but it does not work. So, I am looking for an other solution, or maybe my rule is not correctly configured ?
I have a problem to configure a IPSEC VPN on the SA520W ( 1.0.39) with Cisco VPN Client (5.0.05.290). In the logs are following error:
ERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.x
connecting to separate private lans:
A) 192.168.1.x
B) 192.168.0.x
A is behind a Watchguard XTM25 11.5.3
B is behind a CISCO SA520W
Both have static public facing IP's.
B only has a IP based PBX system attached to it over a SIP ALG. (originally it was hooked up to the watchguard but they didn't play nice, but works great with the Cisco. Problem is the Cisco don't have all the features of the Watchguard)
A has all my users workstations attached. The issue is that computers on A need to talk to server on B for a desktop application to work. Since they are on separate subnets, it isn't working. The app itself still doesn't work by port forward/sNats, etc.
A & B are right next to each other, so cabling between them is not an issue.
Currently, I have a cable between the watchguard and the Cisco. The watchguard end is configured with a static private ip on the subnet A (the cisco side), and plugged into the lan on the cisco side. I have a policies to let all traffic flow freeley, and from the logs on the Watchguard, all A subnet traffic is correctly going to the Cisco via said cable.
But, nothing is coming back from the Cisco. So my question is, how can I get the Cisco to play nice with the other subnet and send traffic back to the B subnet?
I have a problems with one SA520W.The LAN port don't work correctly. If i connect PC directly via ethernet cable (i try 2 different cable and 2 different PC) the DHCP don't assign an IP. If i reset to factory default and manual insert IP (192.168.75.1) don't work.
View 2 Replies View RelatedI have setup an SA520W and configured SSL-VPN for our small business. Everything seemed to go smoothly and I tested SSL VPN by logging in and playing around a bit which seemed to be fine. However, shortly after deployment I started getting complaints about it being much slower than our old VPN through the consumer grade router I just replaced. I investigated and tested with IE8 and Chrome on Windows XP 32-bit with several different machines, and in all instances it did seem very slow indeed. While looking around I noticed that the Task Manager under the Networking tab shows the SSL VPN connection as VirutalPassage at 64 Kbps. Going into Network Connections shows VirtualPassage under the Dial-up heading with device name Virtual Passage SSLDrv Adapter. Additional properties describe it as an ISDN channel. I have attached an image of the Task Manager pane.The router is running the latest firmware of 2.1.51. It is connected via a static IP that does not require a login, to our dedicated 5 Mbit / 5 Mbit ethernet over copper link to our ISP. We get great speeds and low latency through everything but SSL VPN connections. I haven't done anything fancy so the router certificate is the factory default. Currently we are using the existing 2 SSL VPN licenses that come with the router until we need more access, at which point I want to upgrade to the 25 user bundle. However, I don't feel comfortable upgrading until I get this resolved, because 64kbps simply cannot work for us for a VPN solution.how to configure the SSL VPN to not limit at 64kbps? My engineers are making fun of me for bringing us back to dialup, and I have to agree with them!
View 1 Replies View RelatedIs is possible to set the port number for syslog eg 192.168.75.50:20514 ? i presume the protocol would stay udp
View 3 Replies View RelatedI have a router that I have not used for a year or so...I just recently moved to a new location and was trying to set it up...I completed the set up disk several times but I keep getting an error that says my router is connected but there is no internet access...When I plug the port directly to my PC I have internet...The router that I am using is Linksys WRT54G...I have even tried resetting to factory settings and I still can't get it to work.
View 15 Replies View Relatedif my SA520w will support link aggregation for network devices within my LAN. If so, is there a Cisco wiki or how-to on how to setup this up in the SA520w? I only find a brief mention of this in Section D of the manaul.
View 1 Replies View RelatedA new Windows 8 computer can't access the SSLVPN corporate connection.
When we try to access the SSLVPN website to download the launcher (you have to download the VPN launcher everytime for our configuration), you can log in and that's fine, and then you can click on the VPN Tunnel link, a popup shows up but it doesn't actually download the launcher. Solutions we've tried so far:
1) Reinstalling C++ Redistirbutable
2) Adding the site to trusted sites and allowing unsigned ActiveX controls
3) Removing all internet objects through internet options.
Is there anything else we can try?
We have configured new 2911 router with HWIC-2T with it.However we are seeing serial interfaces up, but can hardly ping other end. Again we are seeing a lot of CRC errors on serial interface.
But if we connected same cable, with other old router 2811, it works fine. Confiuration is same on both the routers. [code]
Our company just recently bought a CISCO SA520W Security Appliance from a distributor here in the Philippines. Unfortunately, after a month of use, the LAN ports on the appliance started losing power. We reported this to the distributor and they sent a CISCO engineers to check on the unit. The engineers found the unit to be defective and need to be replaced.
Three weeks after the distributor pulled-out the unit, I have followed-up the status with them. They told me that they got no definite ETA from CISCO for the replacement unit. I followed-up with them again after a week. This time, they told me that the device is already in transit and it is coming from CISCO USA but they still don't have an expected time of arrival to give me.Does it really take more than a month for CISCO to replace a brand new defective unit? The serial number of our appliance is DNI1610G0G7.
I have Dlink N300 router and also WRT54G2 router now with DD-WRT firmware, configured as a repeater.I have a PPPoE connection through Dlink router and want to extend signals farther, hence want to use Linksys (WRT54g2) as a repeater.I have set up the linksys as repeater but dont know how to check if its communicating with my Dlink and also I not able to get internet connection from the repeater.
View 5 Replies View RelatedI configured a 2811 series router for dmvpn. My two tunnels are up but one of the tunnel is flapping with this message.
View 4 Replies View RelatedI have a NM-1CE1U working on my router 2600 , configured with frame-relay . But seems it does not work on my router 2811. I have check that the replacement is HWIC-1CE1T1-PRI , right ？
But the problem is these two modules have different interface type , I want to keep my cable interface type and find one module card working on 2800 or 2900 router , can configure frame-relay.
I have configured policies to shape the traffic on the interface of cisco 7206 router. Now my managemet wants to configure these policies on time based ie policy should be applicable during specified time period onle. Is it possible? if yes how to configure it?
View 11 Replies View RelatedA customer runs a 5508 WLC for quit a while. several dozens AP's are spread all over Europe an run just fine. All the AP's have a VPN based connection over an MPLS service provider, so we are using 10.x.x.x addresses only. We have upgraded to release 7.2.111.3 to support OEAP 600 and we have configured NAT in the Firewall as well a policy to support the home office AP. Everything works fine until the switch where the WLC was attached to crushed. From this moment on, all internal AP's ar no longer able to register at the WLC. A log at the console port on an AP shows that it tries to access the external (NAT) IP address. We had to remove the NAT flag to support the internal AP's.
View 3 Replies View Related