I setup RV042s at a clients offices for the VPN support and am now finding that multiple sip clients behind the router does not work. I found a thread on tech and it looks like there's a case open for the issue. url... How to get this working other than assigning IPs for the phones and dealing with different ports.
View 1 RepliesI'm trying to setup 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24.I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 1 Replies View RelatedI have 3 different office location and I need to set up a LAN so that all three are connected and can share info?
View 1 Replies View RelatedI bought 2 RV180 to setup a VPN tunnel between a remote site and central office.The VPN tunnel is established, I can ping from central office to remote site but browsing on that server fails. [code]
Seems the routing is not really working through the VPN Tunnel.
One of the persons in our company wants to have a phone at his home....(not Cisco) as well as connectivity to servers and other resources at our office. There's talk of using an existing RV042 our office and placing another at the person's home. The office has a static IP address from our ISP, but at the person's home, it will be DHCP from the ISP.
View 4 Replies View RelatedI have recently installed four Cisco RV042 v3 VPN routers for a customer of ours to replace existing Nortel Contivity 1010 devices which were providing VPN tunnels from the customer's 3 branches to their headoffice. The original Nortel devices were working perfectly but the customer wanted some firewall rule changes and the Nortels were proving to be somewhat inflexible and incomprehensible in their configuration hence why they were replaced.
When installing the Cisco routers I configured the VPN settings to match the Nortel device settings so that I could swap out a branch at a time without taking the whole setup down for a day.The customer has a Unix based dumb-terminal application running on a server at headoffice that they access from their branches using terminal emulators on Windows PCs and thin client hardware devices that support vt100 terminal emulation.
Prior to installing the Cisco RV042's everything was working fine. Now they are using the RV042's they keep getting the sessions from their branches dropped. Both PC users and thin client users are losing sessions and it happens with active and idle sessions. I have checked the logs on the routers when users are disconnected and there is nothing logged at that time (other than my login)... I had thought maybe it was to do with tunnel renegotioations so I have set to phase 1 / phase 2 SA timeouts to 86400 & 28800 seconds respectively but this has had no effect. I had also seen somebody advised disabling 'SPI' in the firewall... I have tried this and it makes no difference.
why QuickVPN clients can only reach RV042's LAN Network and not able to access subnet 1 remotely, however PPTP clients can access both..
Firmware Version : v4.1.1.01-sp (Dec 6 2011 20:03:18)
Working Mode : Gateway
Multiple Subnet: Enabled
Device IP Address : 192.168.10.1
LAN: 192.168.10.1/255.255.255.0
Subnet 1: 172.16.10.1/255.255.255.0
QuickVPN clients able to reach all the resouces inside 192.168.10.1/24 remotely, but unable to access 172.16.10.1/24 network.Network 192.168.10.1/24 able to communicatie with network 172.16.10.1/24.PPTP clients able to access both subnets remotely.
I'm currently using DynDNS for my Dynamic DNS Provider with the RVS4000, but I'm looking at upgrading to the RV180 and switching my Dynamic DNS provider over to DNS Made Easy since I can get all my DNS hosting under one roof. Does the RV180 support DNS Made Easy in its Dynamic DNS client? If not, could it be added in a firmware update?
View 3 Replies View RelatedDoes cisco 3600 support office extend feature? If yes, is there a controller requirement? I know cisco AP 600 supports office extend
View 24 Replies View RelatedI have a Any Connect setup and able to VPN into my office.i bought a ASA5505-SW-UL that is unlimited user (UL) software license but now the vendor tells me that: From the ASA you can saw the unlimited license is for inside hosts, instead VPN client's, by default, ASA 5505 included only 2 VPN client's and can supported up to 25 VPN client's, your license look only default 2 VPN client's. If need more VPN client's connect, you have to purchase the additional VPN client's license. I am just wondering his statement TRUE/FALSE, because i thought ASA5505-SW-UL means unlimited license
View 4 Replies View RelatedI have a problem with a branch office setup, and I can't for the life of me think of what the problem is.I have a remote office setup, using an ASA 5505 that is set up to establish an easy vpn connection to the central network. The connection at the branch office is a 20/5 cable modem, the central network has a 25/25 fiber connection.
The issue I have is this. Wired clients work fine at this branch office, at least 95% of the time. I have a lightweight AP there that can come up and join the controllers at the central network, no problem. I haven't done anything with H-REAP because there are really no resources locally they need that would allow them to do their work, so all traffic is tunneled back to the WLC.
Wireless clients can authenticate to the AP, and I can get 15-20ms ping responses from them all day. Latency never comes close to the 600ms proposed limit with CAPWAP. Yet, for some reason the performance of the clients is problematic. Webpages will frequently not load correctly, they experience some freezing, and with one application we use - it refuses to load completely.If we bring these same computers to an AP connected to our central network, on the same SSID, they work flawlessly.
Something about this particular location is causing a lot of grief for our users.For what it's worth, we are running WCS 7.0.230.0 and the WLCs are on 7.0.116.0. The ASA is running a pretty basic configuration, pretty much out of the box with the easy vpn configuration entered.
I was into IBM iSeries all these years (15 years) and just got into Microsoft Programming(.NET) I have done a program in csharp.net which gets input from the users and dump it into a database. 50 users are going to do the data entry with just one database. As I dont have much knowledge on sharing/accessing applications/database in a network environment (PC based).
View 1 Replies View RelatedI have been tasked with the technology update of our office and have have MAJOR questions which I hope can be answered here, so here goes;
First a little history, I have an electronics degree and a certificate in computer technology, so computers are not something new to me, however networking IS.I have a VERY LIMITED budget to work with, which I'm sure is not unheard of before, with the following equipment already available:
1 MFP currently on lease connected via network
3 totally junk PCs running 3 different versions of Windows from XP to 7
A DSL internet connection
A wireless router
A wired 8 port switch
What I would like to do is begin with a basic server, 7 clients, shared internet on all machines (including external via login), An MFP, at least 1 NAS for data storage, 1 NAS for backup of all drives.
I have recently managed to configure a setup where I have 2 srp527's one at office one at home.Have 1 fixed IP at the office and 1 fixed ip at home.I have configured the srp at work to be a vpn server and have configured the group and 2 user profiles. This allows me to have 2 concurrent sessions over the vpn to my office from desktop and laptop at the same time. Connections fire up perfectly no problems.From the desktop, I connect using vpn client with user profile 1 Once connected, I then connect to my workstation machine at the office using remote desktop.This gets me super fast access to office files and large spreadsheets without downloading the whole file over the vpn and is working perfectly.
If I then additionally connect from the laptop using the vpn client with user profile 2 the remote desktop connection drops.Disconnect the laptop connection, remote desktop comes back.Have isolated this to being 2 connections arriving at the srp at the office from the same external ip. If I connect my laptop to my phone as a hotspot rather than using my home LAN, both connections are made and remote desktop has no interruptions. Is there a way I can overcome this through re-configuration of the srp at the office or is this a limitation with the srp?
I have finally got my office extend AP to connect to my companies 5508 controller by enabling NAT on the management interface and can see all the cooperate SSID's. However when I try to connect to the SSID my client either gets a local IP address from my home router or then cannot get any IP address.
View 9 Replies View RelatedI just joined this company and they already ad a VPN to one of their partners that provides them access to some resources. We have now added a 2nd location but the partner wouldnt allow a 2nd VPN tunnel so the decision was made to give the new location a ASA5505 to tunnel thru the main office to access the resources at the partners site.Using ASDM i believe i was able to setup the tunnel to the main office but there is no resource there to use. Now i'm stuck and i do not know what to do to get to the partner site
View 4 Replies View RelatedWhat are the best network engineering practises for a small/medium sized office?Currently I have set it up like this:The top floor has all the sales people, each desk has a hub underneath which connects all computers at that desk together, and the hum is connected to a switch under the floor. There are about about 8 desks each with about 4 computers, so 8 hubs.They all go into a 10/100 switch, which is then connected to an 1gb switch on the bottom floor via a 1gb port on the top floor switch, via a cat6 cable.We then have internet > modem > router > the 1gb switch. Our main server is also connected to that switch along with all the computers for the ground floor, except these computers have 1gb switches under the desks instead of hubs. The main server is the DHCP, DC, DNS and file server. We have also setup another server which acts as a backup DC and is also a DNS server.Is there anything wrong with this configuration? We have been having problems with the router losing connection to the internet and warnings on the main DNS server.
View 6 Replies View RelatedI presently have a fiber internet connection to my office with about 40 wireless users on a single AP. The connection keeps dropping. Probably due to too many users on a single AP?
1. My question is similar to aniketchitale's, can get another wireless router, create a different SSID (eg. router1 and router2), but both wireless routers still connected to the same fiber connection. In other words, I would like to segregate the first 20 users to router 1 and the next 20 users to router 2.
2. By having 2 wireless routers each with their unique SSID, will all the users still be able to access to the same printer in the office?
I have got two 1841 and one 881 cisco router. I can keep any one of this router at HO and remaining at branch office. I have got a static internet IP at HO but dynamic IP at branch office. I want to setup a VPN to connect to HO from branch office through router. The branch connects through a private IP for internet purpose. Which VPN is the most secure and best for this purpose.
View 1 Replies View RelatedWe're looking at deploying both office extend and also a guest wlan. Both would require a WLC in the DMZ.My question is can one 5508 WLC be both a guest anchor and have office extend APs on it at the same time?
View 2 Replies View RelatedXYZ Corporation currently employs eight people but plans to hire 10 more in the next four months. Users will work on multiple projects, and only those users assigned to a project should have access to the project files. You’re instructed to set up the network to make it easy to manage and back up. Would you choose a peer-to-peer network, a server-based network, or a combination of both?
View 1 Replies View RelatedI have two sites setup with a gateway to gateway VPN. Both gateways are RV042s. I have a resource on Site B ( a VoIP Phone Switch) that needs to be accessed thru Site A.Question: Does the RV042s support port forwarding thru the VPN tunnel?I have configured a port forward on Site A's router and the router's firewall log at Site A shows that connections are being accepted, but a packet capture at Site B in front of the switch does not contain a data stream. To answer the obvious question, I can not control the path that data is being sent so I would not be able to redirect the data stream to Site B from the source.
View 1 Replies View Relatedwould Cisco 1841 model router with IOS version 12.4(15)T10 support vpnclient-winx64-msi-5.0.07.0440-k9.exe client software?
View 1 Replies View RelatedQuestion is in the subject line. Maybe I am missing something, but this does not seem to work (No such file or directory).
View 3 Replies View RelatedMy workplace currently has one AD Forest. Slowly we have drifted in to two slightly separate businesses and my boss wants us to create a new AD Forest and segregate the users doing each business. Although we will all be in the same office, each side will authenticate to a different DC. The problem is, that we have some resources that still need to be shared and I would like to share them as eloquently as possible without converging the networks too much. The two networks will be in the same server rack but they will logically appear as this:Forest1.local (original)
-Cable Internet -- Router A (192.168.1.x) -- 48-port switch A -- PC/Phones/Domain Controller AForest2.local (new)
-Cable Internet -- Router B (10.1.1.x) -- 48-port switch B -- PC/Phones/Domain Controller B.
The problem I have is that the users in the "new" network need access to a shared folder, shared customer DB, and shared printers on the original Domain Controller, named "DC A" above. I have complete control over both networks but cant figure it out the best way.My main concern is physical access between the networks. How will a pc on the 10.1.1.x network know where printer 192.168.1.2 is? I thought about creating a forest trust in order to assign proper permission but how will they resolve the names on a different subnets? The two "routers" are just simple SOHO type routers so I cant do much there. I thought about connecting the two switches together but don't know if that would work. Wouldn't the data just get passed to the default gateway (router) anyway. The router would then just drop it. I also though about using the 2nd NIC in each DC and connecting them in each other's subnet. But again Im not sure if it matters if the DC's can reach each other or if the PC's would have to be able to reach the other subnet etc. I also thought about just creating some kind of VPN (hamagachi) or whatever to go out into the internet then back into the other router to the network.The problem is wouldnt every computer wanting to access the shared folder have to have this setup. I would like to limit setting things up on workstations and just limit config to the DC's if possible.I basically just want users in subnet two to be able to map a drive and access printers on DC in subnet one.
How can i implement networking in my THREE floor office by using routers and switches?
View 1 Replies View RelatedI'm using a RV082 with latest firmware v4.0.4.02tm in one of our branch offices. Sometimes the tunnel to the main office (IPCOP 1.4.21) fails.
Both sides display the status "tunnel connected" but IP traffic doesn't go through. If i try to ping the main office using the RV082 diagnostic feature, the RV082 seems to run into a loop...the window continues refreshing without any error message and i'm not able to cancel the test. If I restart the RV082 using the web interface, the "diagnose" and VPN problem still exists, even if the web interface told me that the device did a restart.
The only solution is to to a cold restart of the RV082. After that, the VPN tunnel works again....
This problem occurred 3 times in the last 3 weeks. I never hat this problem with previous firmware versions at this ot other sites.
transferring a workgroup laptop to a office domain
View 1 Replies View RelatedI'm going to move offices into a shared situation with 3 companies. Each company will want its own private network so there's no snooping between companies. I am planning on using VOIP for the phone system (Nextiva cloud based). Is it possible to set up the system so that each company has access to the VOIP system but yet remains sequestered in the their own network for everything else. I was hoping to do this with one data port at each workstation using Cisco SPA-303 phones. The way I understand this, is that the phone plugs in to the data port and you daisy chain the workstation off from each phone. Is this possible to do this while having the system I described? Another wrinkle is that I'd also like all the networks to be access shared printers.
View 7 Replies View Relatedi'm trying to setup a local DNS server to manage small office local-only domain names for our servers. i have the DNS working properly (resolving local machines and using the ISP dns if it can't). so i put the DNS server ip into the "Static DNS 1" field of the router settings. the other 2 static dns fields are empty.the problem is that the router is still using the ISP dns server as the primary and my local dns server as the secondary. i verify this in two places. first, if i go to the "status" tab, DNS 1 shows the ISP server while DNS 2 shows my local DNS server. secondly, if i connect to the wireless device with a linux-based machine, the /etc/resolv.conf file shows the nameserver ips in the same incorrect order.
View 1 Replies View RelatedI have a customer that wants to purchase an ASA 5510 security plus to terminate client VPN access for an external support team. The customer claims to want URL content filtering/proxy which leads me to suggest a CSC SSM 20 plus module. But upon further conversation, he mentioned wanting IPS. In this case, the customer does not seem to know the difference between the URL content filter/proxy and the IPS and uses both terms interchangably.
1. What would you suggest in your expert opinion would be the best module to get for this customer? IPS or CSC
2. If I go with the CSC module, where can I find good documentation on how to configure it and get it up to date?
3. does the CSC module provide any web proxy functionality?
Is there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies View RelatedI've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.
View 5 Replies View Related