Cisco VPN :: ASA5505 Setup Tunnel To Main Office
Jan 21, 2013
I just joined this company and they already ad a VPN to one of their partners that provides them access to some resources. We have now added a 2nd location but the partner wouldnt allow a 2nd VPN tunnel so the decision was made to give the new location a ASA5505 to tunnel thru the main office to access the resources at the partners site.Using ASDM i believe i was able to setup the tunnel to the main office but there is no resource there to use. Now i'm stuck and i do not know what to do to get to the partner site
View 4 Replies
ADVERTISEMENT
Oct 27, 2011
I'm using a RV082 with latest firmware v4.0.4.02tm in one of our branch offices. Sometimes the tunnel to the main office (IPCOP 1.4.21) fails.
Both sides display the status "tunnel connected" but IP traffic doesn't go through. If i try to ping the main office using the RV082 diagnostic feature, the RV082 seems to run into a loop...the window continues refreshing without any error message and i'm not able to cancel the test. If I restart the RV082 using the web interface, the "diagnose" and VPN problem still exists, even if the web interface told me that the device did a restart.
The only solution is to to a cold restart of the RV082. After that, the VPN tunnel works again....
This problem occurred 3 times in the last 3 weeks. I never hat this problem with previous firmware versions at this ot other sites.
View 1 Replies
View Related
May 9, 2013
I have a Any Connect setup and able to VPN into my office.i bought a ASA5505-SW-UL that is unlimited user (UL) software license but now the vendor tells me that: From the ASA you can saw the unlimited license is for inside hosts, instead VPN client's, by default, ASA 5505 included only 2 VPN client's and can supported up to 25 VPN client's, your license look only default 2 VPN client's. If need more VPN client's connect, you have to purchase the additional VPN client's license. I am just wondering his statement TRUE/FALSE, because i thought ASA5505-SW-UL means unlimited license
View 4 Replies
View Related
Aug 18, 2012
I bought 2 RV180 to setup a VPN tunnel between a remote site and central office.The VPN tunnel is established, I can ping from central office to remote site but browsing on that server fails. [code]
Seems the routing is not really working through the VPN Tunnel.
View 4 Replies
View Related
Jun 10, 2012
We have a main office and 4 remote offices (only showing 1 remote office in the diagram). We are using GRE over IPSec VPNs to the remote offices which terminate on the 2811 router in the main office. We are using the 2811 as it is the only device that we have that can terminate GRE. The 2811 router is connected to the outside switch and is configured with a public IP address. We also have a ASA5510 in the main office which is connected in the same manner and is used for Web, e-mail traffic etc.Both the main office and remote offices have a 10Mbps Internet connection.
We have an issue with voice quality between sites as we are finding it difficult to control bandwidth utilization in the main office. When users in the main office download web content it can saturate the 10Mbps Internet connection causing voice quality issues. We have configured outbound shaping on the branch routers to make sure that aggregate inbound traffic from all branches to the main office does not saturate the link but we cannot control traffic from the Internet.I understand that controlling inbound traffic from the Internet is difficult without controlling QoS on the ISPs side. Is there any way that can reserve inbound bandwidth to ensure that web traffic does not impact voice? Also in this design, which is the best place to configure outbound QoS from the main office?
View 4 Replies
View Related
May 18, 2012
I have been told to connect our branch offices over outdoor point-to-point wireless CPE. The wireless brand is Orthogon. The Main office got cisco 4507 L3 switch where all building switches terminate. DHCP,DNS and all application are hosted in main office. The branch office got ONE 24 port POE Switch cisco 2960 where all users will be connected, On Port 0/24 of 2960 switch at branch will terminate the outdoor Wireless and other end will be terminated on 4/15 of 4507 at main office? what command I need at both interface where Wireless is terminated.when we connect floor switches to 4507 we got these commands on access switches
vtp mode client
vtp version 2
vtp password cisco1
vtp domain LIC
Fiber termination port configuration - switchport mode trunk
View 3 Replies
View Related
Dec 17, 2012
I am trying to configure access to several remote offices for users who VPN into our main datacenter. The datacenter has a 5520, and the branches are connected through IPSec L2L VPNs. Branches all have 5505 or 5510's. Remote users use IPSec via the Cisco remote Client. Remote access into our data center works, and the L2L VPNs are perfect...just now that i need remote users to access the branches after Remote access VPNing (for support) i cant get that part to work.
View 2 Replies
View Related
Aug 2, 2011
We have used two Cisco RVS4000 to create the IPSec VPN between the main office and the branch office. The main office has SBS 2008. There is a Windows Server 2008 as the domain controller in the branch office. One branch office user has a laptop which is not in the domain, but his exchange account is set up in the Outlook. When he connects the laptop to the branch office network, he cannot connect to the exchange server and get the emails. Is there any configuration to set up in the router, server or Outlook?
View 1 Replies
View Related
Jul 16, 2012
I am connecting to a ASA5505 at from home to the head-office using L2TP VPN.
Head-office then has a connection to other-office via a site-to-site IPSEC tunnel.
When in the head-office (192.168.100.0/24) I can ping/access remote-office (192.168.200.0/24) OK.
When connected remotely to head-office, I can ping/access head-office OK from the road-warrior laptop.
My problem is that when connected remotely from home to the head-office I cannot ping/access the other-office subnet.
On the home laptop the L2TP VPN connection is set to route all traffic to the VPN connection using the HQ as the internet gateway I can confirm this works.
I cant do traceroute (I get timeouts) as my policy doesnt allow and not sure how to enable this properly on the ASA.
names
name 192.168.200.0 othersite
!
interface Vlan1
nameif inside
security-level 100
[code]....
View 1 Replies
View Related
Jul 7, 2012
I have a wireless audio system using several Apple Airport Express boxes currently communicating using 802.11g through my Verizon FiOS MI424WR (Actiontec) router. I also have wireless security cameras and several laptops on the same connection. I occasionally have audio dropouts I suspect due to wireless bandwidth limitations. I have a Netgear WNR3500 Wireless-N Gigabit router that I would like to hang off of the Verizon router and move the Airport Expresses, which are 802.11N capable, to its Wi-fi connection. This would keep my audio streams separate from the video and other wireless traffic and take advantage of the 802.11N.I in configuring the router/s to facilitate this arrangement. I have numerous Windows machines (XP and Windows 7), mostly hardwired, on my main network along with a NAS containing my audio library. So all devices need to be able to see all other devices.
View 3 Replies
View Related
May 23, 2011
I have an existing VPN tunnel from my branch office to corporate.I want to allow my employees to establish a VPN connection to our local branch office where we have a local server, and not go through the corporate office.Can I set up a direct VPN connection to my router/ firewall at the branch office, even when there is a VPN tunnel already connected between my office and corporate?
View 1 Replies
View Related
May 5, 2011
Equipment Cisco1921, HWIC-1ADSL, 2 x GB Ethernet interfaces (Only one used for local LAN) Software IOS Version 15.1(1)T2..I have been asked to configure this router to provide an IPSEC tunnel back to our central office.We have been provided with an ADSL business class 7MB service from Telecom Italia, they have presented the circuit to our office with no terminating equipment (wires only). Telecom Italia have provided us with some IP addressing information as follows (I will not disclose the entire IP address) [code]
I can see that the packet count is increasing both inbound and outbound on the ATM interface. I have read many documents and tried many different way to try and get this resolved, I even logged a call with Cisco but no dice.
View 5 Replies
View Related
Jan 16, 2012
I got a problem with my setup main computer, It work wery god wireless, with very fine speed about 82 mbit in and 24 mbit out. The problem is that it almost don't work at all with cable, even if i turn off the wireless network, the speed is about 2-3 mbit in and about 6-7 mbit out All other computers, tv. printer wireless work very fine.
View 2 Replies
View Related
Sep 20, 2012
At the main site, I have 3 5508 WLCs each part of a mobility group (wlcMain-MG). In NCS, under "System/Mobility Groups" for each controller, I see each controller listed as "local" with the other Controllers listed with the group name "wlcMain-MG". None of the SSIDs are "anchored".
I have a new site with a 2500 series WLC that I would like to push out 2 SSIDs. This site contains two customers. One customer is the Main customer with the second customer leasing space.
I have the Cust2 WLAN at the remote site set to have traffic egress out of a local interface on the 2500 WLC (this traffic is then tunnelled back to their Main location via an ASA which houses the DHCP scope for that vlan). I can connect to this SSID, obtain an IP Address off the ASA and am tunnelling without issue.
For the Cust1 WLAN at the remote site, I would like to broadcast an SSID from the Main location on those same APs which are registered to the 2500. It is my understanding, that I anchor the SSID at the Main site and identically configure the SSID at the remote site. This will allow the end user to authenticate to the RADIUS server at the Main site and be placed upon the correct vlan (we are using DOT1x and dynamic vlans).
For my test, I am starting simple. I have created a test WLAN with no authentication. At the main site, on 5508 WLC3, I have created the test WLAN, and placed the interface into a low security vlan (call it VLAN-low). I have anchored this test WLAN to that controller. At the remote site, I have created the same WLAN (but placed it into the management interface for now - the VLAN-low does not exist at the remote site) and configured that WLAN to anchor back to the WLC3 at the main site. I am unable to obtain an IP address from the remote site. I have placed the remote site WLC in the wlcMain-MG as well. How close does the code need to be on the controllers - the 5508s are at 7.0.116.0 and the 2500 is at 7.0.220.0? What could I be missing?
View 5 Replies
View Related
Nov 10, 2011
I have two ASA 5505 on two different locations(main office and remote office) and I need the remote office to be in the same subnet as the main office since they move computers betweend the offices and they have fixed IP addresses on those computers and they have no right to cahnge to dhcp mode when they move to remore office. Is it possible to create like a bridge over the VPN tunnel so it extens the LAN ?
View 18 Replies
View Related
May 9, 2013
We have a HUB ASA5505 SEC+ with a few other ASA's connected to it via L2L VPN. We have 1 active Static L2L, 1 Active Dynamic L2L, and I'm currently trying to add a Second Static L2L Tunnel.I verified that each WAN Interface can ping each other, and both devices have full internet connectivity. There is no double nat or content filtering going on either. I did notice that my Cisco Remote Access VPN Client won't connect properly through the ASA despite full internet connectivity, but when I connect directly to the modem I was able to connect properly. So apparently the ISP isn't blocking IPSEC traffic AFAIK.
Static2 is currently using a Temporary TAC License since our license is currently awaiting arrival, but a show version output shows that all VPN/3des features are enabled. [code]
View 1 Replies
View Related
Apr 23, 2013
I have a problem with a branch office setup, and I can't for the life of me think of what the problem is.I have a remote office setup, using an ASA 5505 that is set up to establish an easy vpn connection to the central network. The connection at the branch office is a 20/5 cable modem, the central network has a 25/25 fiber connection.
The issue I have is this. Wired clients work fine at this branch office, at least 95% of the time. I have a lightweight AP there that can come up and join the controllers at the central network, no problem. I haven't done anything with H-REAP because there are really no resources locally they need that would allow them to do their work, so all traffic is tunneled back to the WLC.
Wireless clients can authenticate to the AP, and I can get 15-20ms ping responses from them all day. Latency never comes close to the 600ms proposed limit with CAPWAP. Yet, for some reason the performance of the clients is problematic. Webpages will frequently not load correctly, they experience some freezing, and with one application we use - it refuses to load completely.If we bring these same computers to an AP connected to our central network, on the same SSID, they work flawlessly.
Something about this particular location is causing a lot of grief for our users.For what it's worth, we are running WCS 7.0.230.0 and the WLCs are on 7.0.116.0. The ASA is running a pretty basic configuration, pretty much out of the box with the easy vpn configuration entered.
View 7 Replies
View Related
Jun 25, 2012
I was into IBM iSeries all these years (15 years) and just got into Microsoft Programming(.NET) I have done a program in csharp.net which gets input from the users and dump it into a database. 50 users are going to do the data entry with just one database. As I dont have much knowledge on sharing/accessing applications/database in a network environment (PC based).
View 1 Replies
View Related
Feb 21, 2011
I have been tasked with the technology update of our office and have have MAJOR questions which I hope can be answered here, so here goes;
First a little history, I have an electronics degree and a certificate in computer technology, so computers are not something new to me, however networking IS.I have a VERY LIMITED budget to work with, which I'm sure is not unheard of before, with the following equipment already available:
1 MFP currently on lease connected via network
3 totally junk PCs running 3 different versions of Windows from XP to 7
A DSL internet connection
A wireless router
A wired 8 port switch
What I would like to do is begin with a basic server, 7 clients, shared internet on all machines (including external via login), An MFP, at least 1 NAS for data storage, 1 NAS for backup of all drives.
View 3 Replies
View Related
Nov 27, 2011
I have set up an ipsec tunnel between a Cisco ASA 5505 and a Fortigate 80c. The tunnel is set up as I execute pings from inside behind ASA to inside behind FG, however I cannot get connectivity to hosts behind the Fortigate (traffic is allowed through policies configured on the FG). What I noticed in packet tracer is that traffic is dropped at the step 'Vpn lookup' To troubleshoot I have configured a test ('fake') vpn connection through the vpn wizard and get the same result in packet tracer. I run 8.4 software on the ASA and this is part of the relevant config.
View 1 Replies
View Related
Feb 14, 2011
Got a problem routing trafic to my L2L tunnel...
Got an ASA5505 Sec+ with ip 10.45.10.1 on inside interface. Firmware 8.3(1). Got another Cisco router (From my ISP) with ip 10.45.10.254 - This one creates an L2L tunnel - To the 10.45.20.0/24 net.
On the 5505 ive got "route inside 10.45.20.0 255.255.255.0 10.45.10.254 1", and trafic is being directed to 10.45.10.254 as it should.
I know cause I can ping everything one the 10.45.20.0/24 net - But thats it... Cant RDP, connect to fileshare... Nothing.
When i test a PC and set it to gateway 10.45.10.254 I can access everything on the remote network. Do I need some NAT command or an access-list? I've setup AnyConnect VPN on the ASA and I can connect to both networks without any problems.
View 2 Replies
View Related
Aug 9, 2012
I'm having trouble configuring an ASA5505 on version 8.31 code for an IPSec tunnel. I've done this multiple times on 8.2.5 but can't seem to get my tunnel to even attempt to come up on this ASA. Not sure if it's relevent or not, but this remote ASA has never been used for another VPN tunnel before. When I attempt to ping a host on the other side of my tunnel, I just see the following: 8108# sho crypto isa sa
There are no isakmp sas
My local network is 10.1.1.X/24 and my remote peer network contains 66.37.227.X/24. I've been working on this for the better part of the day and would love to get it resolved.
View 8 Replies
View Related
May 20, 2012
I have a number of sites in China, they have decent inter-country connectivity but poor connectivity when going overseas.
We have a single site in China witha dedicated 1:1 leased line that has good conectivity both inside and outside of China.
All the sites in China have ASA5505 firewalls
One of our Citrix farms is hosted in the UK and although the main site with the leased line is fine accessing the farm the other sites are not. I would like to try and tunnel just the citrix connectivity via a VPN to the China head office then use their connection to get out to the farm.
how to tunnel all traffic but not just specific traffic over the VPN.
View 3 Replies
View Related
Sep 2, 2012
I have recently managed to configure a setup where I have 2 srp527's one at office one at home.Have 1 fixed IP at the office and 1 fixed ip at home.I have configured the srp at work to be a vpn server and have configured the group and 2 user profiles. This allows me to have 2 concurrent sessions over the vpn to my office from desktop and laptop at the same time. Connections fire up perfectly no problems.From the desktop, I connect using vpn client with user profile 1 Once connected, I then connect to my workstation machine at the office using remote desktop.This gets me super fast access to office files and large spreadsheets without downloading the whole file over the vpn and is working perfectly.
If I then additionally connect from the laptop using the vpn client with user profile 2 the remote desktop connection drops.Disconnect the laptop connection, remote desktop comes back.Have isolated this to being 2 connections arriving at the srp at the office from the same external ip. If I connect my laptop to my phone as a hotspot rather than using my home LAN, both connections are made and remote desktop has no interruptions. Is there a way I can overcome this through re-configuration of the srp at the office or is this a limitation with the srp?
View 1 Replies
View Related
Jul 6, 2010
I have finally got my office extend AP to connect to my companies 5508 controller by enabling NAT on the management interface and can see all the cooperate SSID's. However when I try to connect to the SSID my client either gets a local IP address from my home router or then cannot get any IP address.
View 9 Replies
View Related
Jun 28, 2011
I have 3 different office location and I need to set up a LAN so that all three are connected and can share info?
View 1 Replies
View Related
Aug 14, 2011
What are the best network engineering practises for a small/medium sized office?Currently I have set it up like this:The top floor has all the sales people, each desk has a hub underneath which connects all computers at that desk together, and the hum is connected to a switch under the floor. There are about about 8 desks each with about 4 computers, so 8 hubs.They all go into a 10/100 switch, which is then connected to an 1gb switch on the bottom floor via a 1gb port on the top floor switch, via a cat6 cable.We then have internet > modem > router > the 1gb switch. Our main server is also connected to that switch along with all the computers for the ground floor, except these computers have 1gb switches under the desks instead of hubs. The main server is the DHCP, DC, DNS and file server. We have also setup another server which acts as a backup DC and is also a DNS server.Is there anything wrong with this configuration? We have been having problems with the router losing connection to the internet and warnings on the main DNS server.
View 6 Replies
View Related
Nov 1, 2012
I presently have a fiber internet connection to my office with about 40 wireless users on a single AP. The connection keeps dropping. Probably due to too many users on a single AP?
1. My question is similar to aniketchitale's, can get another wireless router, create a different SSID (eg. router1 and router2), but both wireless routers still connected to the same fiber connection. In other words, I would like to segregate the first 20 users to router 1 and the next 20 users to router 2.
2. By having 2 wireless routers each with their unique SSID, will all the users still be able to access to the same printer in the office?
View 12 Replies
View Related
Feb 20, 2008
Just bought myself an ASA5505 to replace a PIX 501, and having transferred over most of the previous config I've managed to get the two IPSEC VPN tunnels working as before.
Unfortunately when I try and SSH to the ASA the connection just resets instantly even when the tunnel is up. It seems as if the ASA is actively refusing the connection, though the log doesn't state this. I had always presumed that traffic over an established IPSEC tunnel was implicitly trusted and not subject to usual access-list rules.
I am unable to SSH to the ASA from the 10.0.0.x range, but I can SSH to a machine on 10.27.0.4 (so I know the tunnel is up and working)
Config (minus irrelevant sensitive information) is attached for reference.
Also - though I'm not sure how relevant it is given the tunnels appear to work - when I enter the line "crypto map meepnet-map interface outside" in config mode the ASA reports "WARNING: The crypto map entry is incomplete!" even though I have supplied the access-list, peer and transform-set variables.
View 12 Replies
View Related
Jun 13, 2011
Currently, I have in a number of remote sites (with dynamic public address) a C800.On this Cisco, I have a config for initiating an agressive-mode tunnel to a central ASA.relevant part of the config:
---
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
!
crypto isakmp peer address 1.2.3.4
[code].....
Now I need to replace these C800 by ASA5505. But I don't know how to replace the "crypto isakmp peer address" command in ASA.The C800 transmits both the password (abcdefg in my example) and the fqdn (remotesite1 in the example). how to configure the ASA to build the tunnel the way the C800 did?
View 5 Replies
View Related
Dec 3, 2012
I setup RV042s at a clients offices for the VPN support and am now finding that multiple sip clients behind the router does not work. I found a thread on tech and it looks like there's a case open for the issue. url... How to get this working other than assigning IPs for the phones and dealing with different ports.
View 1 Replies
View Related
Jan 26, 2013
I have got two 1841 and one 881 cisco router. I can keep any one of this router at HO and remaining at branch office. I have got a static internet IP at HO but dynamic IP at branch office. I want to setup a VPN to connect to HO from branch office through router. The branch connects through a private IP for internet purpose. Which VPN is the most secure and best for this purpose.
View 1 Replies
View Related
Oct 6, 2011
I have an ASA 5505 with Base license and a vpn client. The scenario is like this: LAN -- ASA 5505 -- ISP DSL Router---( Internet ) -- Home DSL Router --- LAN -- VPN CLient, The ISP DSL Router gets a public IP address and the ASA gets a private IP address (ISP DSL router doing NAT) and I cant reach the internet with no problem from the LAN´s ASA side but I cant make the vpn tunnel connection from the LAN´s Home side so I told the provider to bridge the ISP DSL Router, to the ASA so the ASA could get the public IP but in order to do that the provider told me to do MAC clonning on the ASA 5505 which I did putting the ISP DSL Router MAC on the ASA. Now the ASA gets the public IP on the outside vlan by DHCP but when I try to make the VPN tunnel I just cannt. I can reach the public IP by ping on the ASA and I can see the pings coming in using debug but I just cant make the vpn client work.
View 2 Replies
View Related
