After enabling AAA FWSM lost opportunity telnet session. FWSM version 3.2(5). In the logs show that resets itself FWSM telnet session.
Conf.,aaa-server TACACS+ (management) host 192.2.151.111
key aaa authentication ssh console TACACS+ LOCAL
aaa authentication enable console TACACS+ LOCAL
aaa authentication telnet console TACACS+ LOCAL
[Code] .....
I can't telnet from a host(Ubuntu 12.10) in our DMZ to an outside MX on port TCP 587. Inspection for ESMTP not enabled. Port 587 enabled for host in DMZ to any.
View 12 Replies View RelatedI am trying to remove a line in a particular access-list configured in a FWSM module using this command "no access-list <acl> line 19 x x x x" but it doesn't work. See below:
FWSM/xxx03(config)# no access-list ?
configure mode commands/options:
alert-interval Specify the alert interval for generating syslog message
106001 which alerts that the system has reached a deny
[code]...
How can I remove a line from the access-list without clearing the entire access-list?
I have a pair of OLD Cat6500's running CatOS:
WS-C6509 Software, Version NmpSW: 7.6(16)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Dec 22 2005, 16:37:19
System Bootstrap Version: 7.1(1)
System Boot Image File is 'bootflash:cat6000-sup2k8.7-6-16.bin'
System Configuration register is 0x2
I know these are no longer supported, but I have to ready them for migration. Recently a problem began with these switches. What happens is that when I telnet to them, I cannot authenitcate via TACACS. This works fine for all our other IOS equipment, just not for these 2 switches. The error is:" % Error in authentication" and then I get kicked back to the login prompt.
The odd thing is that when I connect to the switch via the console port, I can authenticate fine with TACACS.
CMS> /c 14
[Code].....
I have a ASA 5510 firewall with CSC module and Security Plus license for CSC module.Will you tell me how to configure my firewall to send emails to particular mail ID when someone login into the firewall or any virus attacks from outside.
View 6 Replies View RelatedWe have 2 FWSM modules in each 6500 switches. 1st module is having 04 firewall vlan groups with 18 vlan interfaces in a single context firewall. All are working fine with no issues. Recently we create one more vlan on MFSC and add into the same firewall module. However newly created vlan inside the FW is not able to communicate with outside and also outside users not able to reach newly created subnet. But within the firewall zones (other interfaces) it can communicate. Once we did packet capture we noticed that its hitting firewall outside interface only and when we ping we got TTL expired error. we have default routes to outside and there's no any route inside as new segment is within the firewall (no any hop).
I guess there's no limitation on number of vlans that we can assign on one firewall eventhough there is a limitation for number of vlan-group which is 16 max (but we are within that limit).
I'm having a problem with an ASA 5510 and software from Manage Engine (Firewall Analyzer). They are saying that sys log 113019 is not getting data over to the server where the firewall analyzer is installed. I'm checking the config and I see it enabled. Why this particular sys log info isn't making it to the reporting software when other data is.
View 4 Replies View RelatedI currently have an ASA 5510 unit. I have a dmz setup which house some web servers and an inside interface. The web servers contain multiple public ip addresses which I have natted and access is fine.What is the most simple way to enable ping for my dmz from the outside. Meaning if someone outside the network pings one of the servers by its public ip address I would like it to respond to ping.
View 1 Replies View RelatedI enable the IPS on the 2911 router . I am using the Basic IPS signatures that are inbulid on the routers . But sill it showing , that no signature is active .
ip ips signature-category
category all
retired true
ip ips signature-category
category ios_ips basic
retired false
[code]....
I am getting this error on my PIX 535 with 8.0.4 code. The error is b Error : OSPF/RIP cannot be enabled on failover interface, I am getting this error while trying to enable RIP on the firewall. The context is single mode and failover is enabled. When I am disabling the failover the Firewall is accepting the RIP configurations.
View 1 Replies View RelatedWe've got a proyect that requires a few thin clients to connect to a remote PCoIP server.
Looking to the documentation, the only port required to be open through Firewalls is TCP/UDP 4172, however, we've seen (making interface captures) that it somehow also uses ESP (IP protocol 50).
We've got a static NAT translation translating those thin clients to a public IP address, we've created ACLs to allow inbound (shouldn't be necessary as our user is connecting to a remote server) and outbound traffic for TCP/UDP 4172 and ESP and I cannot make it work.
I've also enabled IPSec pass-through Inspection to no avail.
how should we configure our ASA to enable this kind of traffic?
I am currently using ASDM v6.4 and would like to enable the historic metrics feature to view/produce graphs/tables for interface using the Last 5 days, every 2 hours option. how this will impact performance and storage space on the device?
View 1 Replies View RelatedI am trying to implement Microsoft LDAP server with our ASA 5520. The client is using Cisco VPN client and when I am trying to connect I am receiving the following error message:
"Secure VPN connection terminated locally by the client. Reason 413:User authentication failed"
I triggered the debug on the ASA 5520 and everything looks fine .The LDAP server is sending the right information without any error message.
Googled this error message and I found that I need to enable the simultaneous logins to enable. I enabled it but I got the same error message. This configuration is under remote access vpn>group-policies>General>more options.
Can any1 tell me wat is the difference between ASA-SM1 and FWSM.
View 2 Replies View RelatedI want to upgrade a pair of FWSM in active failover from 4.0(4) to 4.1(8) i just want to double check the process. i have tftp access to the primary at the minute. i cannot access the same tftp server with the standby. do i need flip over to the standby to be able to tftp the image across?
failover activehostname# changeto system
hostname# copy tftp://x.x.x.x/c6svc-fwm-k9.4-1-8.bin flash:image
hostname# copy tftp://x.x.x.x/asdm-622f.bin flash:asdm
hostname# reload
Once i have the images loaded i reload both at the same time?[URL]
I am planning for an VSS in Core but firstly I need to upgrade FWSM which is at 3.2 Ver to 4.0.4 (min release) I have checked software dependencies but not sure about Hardware Dependency on Fwsm and Chassis for Eg. Rommon Upgrade on Chassis.
View 7 Replies View RelatedI wanna upgrade FWSM Version 3.1(11) to latest 4.x version is this possible or i have to upgrade first to 3.2 and then to 4.x?
Is there any changes in configuration commands that i need to know? The version that 6500 running is s72033-advipservicesk9_wan-mz.122-18.SXF14.bin,an upgrade to 6500 is needed also?And if so what ios version will i put?Also which is the asdm supported version?
We recently deployed a FWSM on our 6503-e boxes (w/ sup720). NAT is working (PAT) but the issue I am seeing is private traffic from remote sites is not being allowed through the FW. I was able to get the remote site to ping the FWSM itself (inside address), but no hosts behind it. Maybe an ACL issue? Also when I turn off NAT on the remote end, I can than access everything (We are NATng on both ends). Im a routing guy by nature so I will defer this to the security guys out there.
Topology
Hosts (inside/10.15.25.0/24) > FWSM (outside/public IP) -> Core Router -> MPLS CLOUD -> Core Router (NATng) - > Hosts (192.168.1.0/24)
ACLs applied to inside/outside interface
FWSM# show access-list ATX-ALLOW-IN
access-list ATX-ALLOW-IN; 15 elements
access-list ATX-ALLOW-IN extended permit tcp any any (hitcnt=222)
[Code]....
enabling traffic between interfaces on the ASA 5510. Of course I have an outside interface E0/0 and an inside interface (E0/1) for normal operation. The idea was to enable one of the remaining interfaces on the 5510 to attach an internal network resource to for management in case we lost our switch. I am using E0/0 as the outside interface and the inside interface is E0/1. I am wanting to attached a management device on the same inside network IP address range for simplicity. I have E0/2 configured for the same security level (100) as the other inside interface and I also have enabled same-security-traffic permit inter-interface as well but I still cannot access the device on that port. Is there something else I am missing? I guess the best way to explain this is that I want ports E0/2 and E0/3 to act like a "switch" so to say...... The ASA 5505 lets you do this pretty easy but having trouble on the 5510.
View 4 Replies View Relatedaccessing my cisco ASA, last night we were doing VA on our ASA, after that iam not able to access it through ssh nor telnet. its not giving me any error.. i tried from different system also. SSH & telnet allowed from inside to 0.0.0.0 i have re-generated rsa keys when it was working. ASA version is 8.2 now when i connect telent is giving me blank prompt. i can login using ASDM.
View 5 Replies View RelatedI am not able to telnet or ssh to ASA running 8.2.5(33). [code] I am able to ping inside interface of the ASA. Telnet gets stuck at Trying
View 2 Replies View RelatedI have an early model PIX-515 that hasn't been used in a long time but I want to get it working again in a lab environment. I am at loss right now on how to get into it though.
CONSOLE:
I've tried connecting from the PC's serial port to the units console port using Cisco's blue cable with no avail. All I get is a cursor but no response. I've tried using 9600,8,none,1,none as settings and I can sucessfully console a Cisco 1700 router with those same settings in Putty no problem, but it doesn't work with this Pix. I've also tried using other possible common speeds like 1200,1400,4800,19200, 38400, 57600 and 115200 in case the firewall was set to use those and that didn't work either.
[code]...
We have a pair of 6500s with Sup720 running 12.2(33)SXI3. Each has an ACE-20 (s/w A2(2.0)) and FWSM (s/w v3.2(15)). We have reached a limit on the number of rules we can configure on the FWSM, and have determined that we shall upgrade to 4.1(5), with ASDM to 6.2(2)F. A question has been raised regarding the s/w on the ACE-20 modules. Do we need to upgrade them as well?
View 2 Replies View RelatedASA code 8.3 and higher uses NAT objects and totally changes the NAT rule config. I am new to FWSM .... but was wondering if this comparable ? I am lookinig at upgrading FWSM 3.1(16) to a higher 4.1 version .... but have a feeling this could be a huge task if NAT config changes as with the ASA's
View 2 Replies View Relatedam trying to config a FWSM by ASDM 6.2f.there are formerly configured interfaces and new interfaces i created.when i add a new access rule it gets added only to all the old interfaces but not to the new ones i created.
1. what wrong with the new interfces i created?
2. whats the logic of auto adding a rule to "all" interfaces , the rules are incoming rules specific to interfaces or groups , why add the to the rule to "all" intefaces?.
We would like to decommission our FWSMs and upgrade to the ASA 5555Xs. This leads me to ask the following: What would be the most efficient way of doing this without any interruption to production? How to successfully accomplish this?
View 1 Replies View Relatedour FWSM (in 6509) is not coming up, when tried to sesssion up using "Session slot 1 proc 1" command,It is giving error , "Tyring 127.0.0.11 .....connection timed out remote host not responding".
In "show mod" command output at Switch in IOS console: under Card Type Section: it is showing Model & Serial Number correctly, Under MAC address sectino: displaying some MAC address But in Online Diag Status, it showing "Unknown" for Module 1.
We tried re-seating in other slots, but of no use. Giving same error. Some of other forms are saying it is the issue with 128 Mb CF image problem, FWSM is no more reachable from 6509 IOS console. We even tried using FWSM console (using PC-Conse & LCP Console) but FWSM is not contactable.
I am having two dc switches with FWSM modules installed. DC switch1 FWSM (Ver 3.2(12) is wokring as active and Secondary DC switch2 FWSM (ver 3.2.(12) is in standby mode.
From yesterday I am trying to login primary FWSM, It is accepting my username and credentials but prompting again for username please refer below
DXB-DC1>session slot 5 p 1The default escape character is Ctrl-^, then x.You can also type 'exit' at the remote prompt to end the sessionTrying 127.0.0.51 Open. [code]
I have had a strange issue with a pair of FWSM's in 2 6500's, it seems there was a failover but both module's have been reset.
CAT1
Feb 03 17:08:46.525: %SNMP-5-MODULETRAP: Module 8 [Down] Trap Feb 03 17:08:46.522: SP: The PC in slot 8 is shutting down. Please wait ...Feb 03 17:09:01.525: SP: shutdown_pc_process:No response from module 8 Feb 03 17:09:11.382: %C6KPWR-SP-4-DISABLED: power to module in slot 8 set off (Reset) Feb 03 17:10:56.093: %DIAG-SP-6-RUN_MINIMUM: Module 8: Running Minimal Diagnostics...Feb 03 17:10:59.796: %SVCLC-5-FWVTPMODE: VTP
[Code]...
Can I upgrade FWSM 4.0.3 to 4.0.17 with Chassis IOS s72033-adventerprisek9_wan-mz.122-33.SXH4.bin ?
In chassis's slot we have ACE and FWSM slot also. if I will upgrade chassis it will reboot ACE too.I do not want to reload Chassis.
I'm running two C6509 Chassis with FWSM and ACE module install on each chasiss.I have no problem with session into 1 FWSM and 2 ACE modules.But 1 FWSM module can't be access by session command.As I understand two FWSM module status is OK, and working fine.When I tried to session into FWSM, I got these messages..
[code]....
I need to upgrade the fwsm image from 3.1(10) to 4.0(8). Can i do it directly from 3.1(10) to 4.0(8) ?Do i need to upgrade other image also along with Firewall version 4.0(8)?
[code]....
I think I got a strange behavior on a context of my WS-SVC-FWM-1 (on a Catalyst 6509 running IOS 12.2(18)SXF17a) that is running FWSM Firewall Version 4.1(3). This context sends these log messages every ten minutes:
Jul 17 2011 23:31:16: %FWSM-6-302010: 0 in use, 0 most used
Jul 17 2011 23:31:17: %FWSM-6-302010: 2245 in use, 107133 most used
[code]...
If I issue the "show conn" three seconds later the log message, the output I got is: FWSM# sh conn 1041 in use, 107133 most used
In another context on the same FWSM the log message sent every ten minutes is just this one:
Jul 17 2011 23:31:17: %FWSM-6-302010: 1358 in use, 72503 most used
Jul 17 2011 23:41:22: %FWSM-6-302010: 1590 in use, 72503 most used
In this case there is no the log message where the "in use" field and "most used" field are 0 (zero). why does the context send the message with the "in use" field and "most used" field 0 (zero).