I can't telnet from a host(Ubuntu 12.10) in our DMZ to an outside MX on port TCP 587. Inspection for ESMTP not enabled. Port 587 enabled for host in DMZ to any.
View 12 Replies
After enabling AAA FWSM lost opportunity telnet session. FWSM version 3.2(5). In the logs show that resets itself FWSM telnet session.
Conf.,aaa-server TACACS+ (management) host 192.2.151.111
key aaa authentication ssh console TACACS+ LOCAL
aaa authentication enable console TACACS+ LOCAL
aaa authentication telnet console TACACS+ LOCAL
[Code] .....
I have a vpn ssl remote access with a fw asa 5510 version 8.02. When users use any connect vpn ssl they in the Lan can access to the servers,but they can not access using ssh or telnet to inside fw asa.
aaa authentication ssh console LOCAL
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 30
I want to disable the telnet option/feature on ASA 5510
i tried no telnet alone it wont work as i didnt configured any telnet at all.
I have a ASA 5510 that is connected to my ISP and the inside interface that is connected to my router. I have a /30 and need to determine if the configuration of x.x.x.121/30 which is my ISP and also the BVI address on the ASA. The inside router address is x.x.x.122/30 same subnet as my ISP will allow me to pass traffic. Management interface works using a different ip address but not able to get the traffic to pass traffic out to the internet thru the ASA
ISP-------->ASA-------->Router
Bottom Line is that I only have one usable address that is being used by the router and the ISP and ASA are using the other. Will this work?
I have a ASA 5510. I setup basic configuration to test internet with 2 ISPs. My first line works with out any problem. But my second line doesn't work. Even when i wipe the configuration, and setup only my second isp. Internet doesn't work. Can you tell me if there is anything wrong with this config?
CaaaA01# sh run
: Saved
:
ASA Version 8.3(1)
!
hostname CaaaA01
domain-name example.com
[code].....
Are the ASA memory DIMMs created for specific models? Would a 1GB 5510 Memory stick work in a 5520?
View 1 Replies View RelatedI'm trying to setup a L2TP VPN Connection on my ASA 5510 to connect with Android/Windows (Native Clients).I'm using the newest Releases:Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.3(5)
My asa config just the interesting part:
crypto ipsec transform-set trans esp-3des esp-sha-hmac crypto ipsec transform-set trans mode transportcrypto ipsec security-association lifetime seconds 28800crypto ipsec security-association lifetime kilobytes 4608000crypto dynamic-map dyno 10 set transform-set transcrypto map vpn 20 ipsec-isakmp dynamic dynocrypto map vpn interface outsidecrypto isakmp enable outsidecrypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400no crypto isakmp nat-traversal
[code]....
If i try to connect with a Windows 7 Client (NOT behind NAT) I get the Error 691.
I see that Phase 1/2 are working with debug:
Dec 22 16:32:16 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 1 COMPLETED
Dec 22 16:51:25 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 2 COMPLETED (msgid=00000001)
Then I see this "Error":
Dec 22 16:51:26 [IKEv1]: Group = DefaultRAGroup, IP = XXXXX, Session is being torn down. Reason: L2TP initiated
I don't understand why it doens't work....I tried many templates from the net but nothings works.
since our update of Cisco ASA 5510 (active/standby cluster) from version 8.22 to version 8.24 it isn't possible to transfer files from/to a sftp client. The request just times out. SSH from this client is possible.
[Code]...
I have a pair of OLD Cat6500's running CatOS:
WS-C6509 Software, Version NmpSW: 7.6(16)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Dec 22 2005, 16:37:19
System Bootstrap Version: 7.1(1)
System Boot Image File is 'bootflash:cat6000-sup2k8.7-6-16.bin'
System Configuration register is 0x2
I know these are no longer supported, but I have to ready them for migration. Recently a problem began with these switches. What happens is that when I telnet to them, I cannot authenitcate via TACACS. This works fine for all our other IOS equipment, just not for these 2 switches. The error is:" % Error in authentication" and then I get kicked back to the login prompt.
The odd thing is that when I connect to the switch via the console port, I can authenticate fine with TACACS.
CMS> /c 14
[Code].....
accessing my cisco ASA, last night we were doing VA on our ASA, after that iam not able to access it through ssh nor telnet. its not giving me any error.. i tried from different system also. SSH & telnet allowed from inside to 0.0.0.0 i have re-generated rsa keys when it was working. ASA version is 8.2 now when i connect telent is giving me blank prompt. i can login using ASDM.
View 5 Replies View RelatedI am not able to telnet or ssh to ASA running 8.2.5(33). [code] I am able to ping inside interface of the ASA. Telnet gets stuck at Trying
View 2 Replies View RelatedI have an early model PIX-515 that hasn't been used in a long time but I want to get it working again in a lab environment. I am at loss right now on how to get into it though.
CONSOLE:
I've tried connecting from the PC's serial port to the units console port using Cisco's blue cable with no avail. All I get is a cursor but no response. I've tried using 9600,8,none,1,none as settings and I can sucessfully console a Cisco 1700 router with those same settings in Putty no problem, but it doesn't work with this Pix. I've also tried using other possible common speeds like 1200,1400,4800,19200, 38400, 57600 and 115200 in case the firewall was set to use those and that didn't work either.
[code]...
I setup a site-to-site VPN tunnel at the remote ASA5505. I am able to asdm to the outside interface but not ssh. I switch to telnet and still not allow me to access. I added an ACL to allow telnet any to the outside interface but still not working. In ASDM I see the log Here is the second issue. When I want to change the telnet back to ssh using ASDM I got the following error.
View 2 Replies View RelatedWhen users are VPN connected their telnet sessions timeout after an hour of inactivity. Looking at the connections on the firewall they are showing as idle. Is there a configuration change or something else that has to be modified?
View 2 Replies View RelatedI have a question about my ASA 5520, it worked well till two weeks ago, and suddenly cannot be accessed by SSH/Telnet/TFTP....only can use the Consoel port to access it now, but other VPN/ACL setting working well. [code] If I enabled the outside access for SSH like below, it works well for outside port.ssh 0.0.0.0 0.0.0.0 outside.
View 3 Replies View RelatedI am unable to Telnet/SSH/RDP from my inside network to my DMZ. I am not sure where the problem lies, I am able to use VNC from the inside to the DMZ (ports 5800, 5900), and also establish connection on Ports (26700-26899). I have a computer connected directly to the DMZ and those services work to all networks on the DMZ.I have attached Logs of successful VNC connections, unsuccessful RDP and Telnet sessions, and the running config.
View 23 Replies View RelatedI am using a Cisco 2801 Router and currently have Telnet enabled on all interfaces. How do I change that so it is enabled from all inside networks, but not on the outside interface?
View 12 Replies View RelatedI have a cisco asa 5520. i need to forward telnet to a router on the inside interface. Here is what i have done so far but it doesnt seem to be working.
I have created an access-list that looks like this:
access-list 102 extended permit tcp any host 10.10.60.2 eq telnet
But when do this it still doesnt forward my request to the router at 10.10.60.2 . So just to explain what im trying to do. I use Putty, i am putting the outside interface IP into putty, selecting telnet and opening the session. i need the outside interface to see this request and know to forward port 23 to the router on the inside interface with IP 10.10.60.2. The ASA is running version: asa842-k8.bin
I got 2 x 5520 ASAs configured in active/standby mode and they are connected to 2 x 4500 switches in which too configured for failover.Telnet to ASAs is allowed only via subnet 172.18.0.0./24
I can only ping and telnet to the active ASA from subnet 172.18.0.0./24 but not the standby But i can ping and telnet to both the active and standby ASAs within the 4500 switches.
I am having some troubles finding information about how to configure firewall policies (rules, chains, etc.) via telnet on a RV016. The reason for that is that i keep getting some log entries "connection refused - policy violation" and "blocked" even with my firewall wide open (only allow rules on all interfaces, SPI and block wan request disabled, multicast and https enabled, etc.... ). Also, with these exact same rules, i can only connect via PPTP with the firewall disabled. The minute i tick the enable option the tunnel never gets to authentication phase. I then started reading OpenRG manual and many things are quite similar, but some other entries are missing from that manual (maybe some changes made by cisco?). I am trying to figure out some service ids, chains (e.g. the rv016 has some rules redirecting to chains 10, 100, 200 but i can not find them anywhere), and so on. I have only one rv016 and about 60 connections to it so i can not experiment that much without having the whole company on my neck with internet problems.
View 2 Replies View Relatedhow do i change the telnet and enable and vpn user password on asa 5570.
View 4 Replies View RelatedI have a network with 3 sites that are on different subnets. Each site has an ASA Right now, I am only able to connect to the ASA that is connected to the subnet I am connected to.I want to be able to connect to the ASA that are on the remote subnets on the address of the inside interface.The sites are connected all together by site-to-site VPN.Is there any way I can achieve that without opening the outside interface directly on the Internet?
View 2 Replies View Relatedi have a problem regarding VPN setup on 5510 ASA and other side 5520 ASA. previously we created the VPN but it works only when the other side start pinging to our side.i have to mention here that we created the BI- Directional traffice on for both side .we have to configure tunnel up for both side .
View 2 Replies View RelatedI woudl like to ask all of you that i have ASA 5510 and i want to do VPN client authetication with LDAP, after verify username and password with AD and it use policy with ACS?
View 3 Replies View RelatedI have one ASA 5510 on main office that access the internet trought of a private link and one ASA5505 on the branch office that access the internet trought of a ADSL link with dynamic IP.
Behind ASA 5510 the network is 10.8.40.0/24 and behind the ASA 5505 the network is 10.30.103.0/24. I want access both network trought of the frame-relay link and the internet link with EzVPN.I make that access only ip on the main office, this comunication go to frame-relay link and the everyone go to the VPN.When the traffic go to the frame-relay link, I use a NAT Static Policy that change the source 10.30.103.0/24 to source 10.40.103.0/24. Its work OK when a VPN do not UP.When the VPN is UP, the NAT dont work and the packet go to the true IP (10.30.103.0/24).
I would like to use a Cisco 1921 at my house and create a "Easy VPN Remote" connection to our ASA 5510 at work. Can I use the Easy VPN Client with the base license, or do I need the security license to take advantage of the VPN tunnel?
View 4 Replies View RelatedWe are using the newest release of AD Agent (1.0.0.32.1, built 598). The ASA Firewalls 5520 are having the software release 8.4(3)8 installed.When somebody tries to connect thru the Identity based firewalls from a citrix published desktop environment (PDI) the connection is not possible. Checking the ip-of-user mapping on the firewalls (show user-identity ip-of-user USERNAME) mostly doesn't show the mapping of the USERNAME and the PDI the user is logged in. The user-of-ip mapping of the PDIs IP-address shows mostly other users, which then are used to authenticate the acces thru the firewalls.
What is interesting, that on the AD Agent using "adacfg.exe cache list | find /i "USERNAME"" i can't see the PDIs IP-address neither because it is mapped to another user.Is Citrix Published Desktop environment supported to connect thru Identity based Firewalls? How AD Agent, Domain Controllers and Firewalls are working together? On the firewalls with "show user-identity ad-agent we see, the following:
-Authentication Port: udp/1645
-Accounting Port: udp/1646
-ASA Listening Port: udp/3799
Why Cisco does use 1645 and 1646 and not 1812 and 1813?The Listening Port is used for what purpose? we tried the AD Agent modes full- download and on-demand with the same effect.
I restarted my pix firewall cisco pix 515 and when i start it again the Act lamp and the firewall didn't work .
View 1 Replies View RelatedI have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
I need to create a firewalled segment that not only separates hosts from general population, but also from each other. The solitary confinement of firewalled segments.I know that I could create a bunch of sub-interfaces, one for each host or group that needs to be isolated, but I'd really rather not have to do that if possible. 1) It could become a management nightmare between ACLs and sub-interfaces and 2) it's a waste of IP addresses.s there any way that I can create a bunch of separate VLANs behind the firewall and have them all terminate at the firewall, using a single firewall IP address for the gateway?
VLAN 1 - hosts 1.1.1.5 and 1.1.1.6VLAN 2 - hosts 1.1.1.7
Firewall DMZ Interface - 1.1.1.1VLAN 3 - hosts 1.1.1.8 and 1.1.1.9
This way, the hosts are isolated and can't talk to each other unless they're on the same VLAN.I'm working with an ASA 5510 running 8.2.4(4).
I have a ASA 5510 firewall with CSC module and Security Plus license for CSC module.Will you tell me how to configure my firewall to send emails to particular mail ID when someone login into the firewall or any virus attacks from outside.
View 6 Replies View RelatedWe were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies View Related
