Cisco Firewall :: ASA 5510 - Saving Config Via Scp Doesn't Work After Updating To 8.24

Apr 5, 2011

since our update of Cisco ASA 5510 (active/standby cluster) from version 8.22 to version 8.24 it isn't possible to transfer files from/to a sftp client. The request just times out. SSH from this client is possible.

[Code]...

View 2 Replies


ADVERTISEMENT

Cisco Firewall :: Internet Doesn't Work On ASA 5510 For Backup ISP

Feb 15, 2012

I have a ASA 5510. I setup basic configuration to test internet with 2 ISPs. My first line works with out any problem. But my second line doesn't work. Even when i wipe the configuration, and setup only my second isp. Internet doesn't work. Can you tell me if there is anything wrong with this config?
 
CaaaA01#  sh run
: Saved
:
ASA Version 8.3(1)
!
hostname CaaaA01
domain-name example.com

[code].....

View 2 Replies View Related

Cisco Firewall :: L2TP IPsec Doesn't Work On ASA 5510

Dec 21, 2010

I'm trying to setup a L2TP VPN Connection on my ASA 5510 to connect with Android/Windows (Native Clients).I'm using the newest Releases:Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.3(5)
 
My asa config just the interesting part:

crypto ipsec transform-set trans esp-3des esp-sha-hmac crypto ipsec transform-set trans mode transportcrypto ipsec security-association lifetime seconds 28800crypto ipsec security-association lifetime kilobytes 4608000crypto dynamic-map dyno 10 set transform-set transcrypto map vpn 20 ipsec-isakmp dynamic dynocrypto map vpn interface outsidecrypto isakmp enable outsidecrypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400no crypto isakmp nat-traversal

[code]....
 
If i try to connect with a Windows 7 Client (NOT behind NAT) I get the Error 691.
 
I see that Phase 1/2 are working with debug:
Dec 22 16:32:16 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 1 COMPLETED
Dec 22 16:51:25 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 2 COMPLETED (msgid=00000001)
 
Then I see this "Error":

Dec 22 16:51:26 [IKEv1]: Group = DefaultRAGroup, IP = XXXXX, Session is being torn down. Reason: L2TP initiated
  
I don't understand why it doens't work....I tried many templates from the net but nothings works.

View 5 Replies View Related

Saving / Updating Network Files To Intranet?

Aug 23, 2011

I am trying to put a link on our Intranet page to several documents that are updated daily by specific users. These users save the documents in their department folders, which are only acessible by their department and I.T. (me). Right now I have a .bat file that checks every half hour of the work day to see if it has been updated, if it has it will be moved to a location in the Intranet folder which will update the link on the Intranet. While users can view the Intranet, they do not have access to view the files or folders that house the Intranet html coding etc.This option works but our users are complaining that it isn't instantaneous. Any ideas how I can do this on a network while keeping everyone's security in place and not give them extra rights to the Intranet folders?

View 3 Replies View Related

Cisco Security :: 5510 Doesn't Save Config And Disk0 Error

Jan 3, 2013

my Cisco ASA 5510 doesn't save the  configuration to the disk.

View 1 Replies View Related

Cisco Wireless :: LAP1142N Not Saving Config

Feb 11, 2013

I have a wireless deployment using a 5508 controller and 90+ LAP1142N lightweight access points.Everything is going relatively well, except I have about 3 that do not keep their config (hostname and AP group) past a reboot of the access point.When they do come up after a reboot, they go back to the default hostname of the mac address and are placed in the default-group AP group.

View 5 Replies View Related

Cisco WAN :: Saving / Copying Config Files Using Usb In 3750 Switch

Sep 9, 2012

I am having difficulties saving, loading conifg files from a USB, what is the correct command for loading a config file from USB for cisco 3750x switch.

View 1 Replies View Related

Cisco Firewall :: 5510 - Move Config From One ASA To Another?

Dec 17, 2012

I'm upgrading ASA firewalls from a 5510 (running 8.2.2 code) to a 5515-X (running 8.6.1 code).  What is the best way to move the existing config to the new firewall?  Can I simply copy it?

View 2 Replies View Related

Cisco Firewall :: ASA 5510 ACL Config Guidance

Sep 27, 2011

we are looking at having a 172.168.40.0 network on our LAN. BUT i want to tie it down to JUST accessing the internet!So i'm looking for some ideas on how that ACL would look like.i have an ASA 5510 as our firewall and i've attached a simple network diagram for reference.

View 7 Replies View Related

Cisco Firewall :: ASA 5510 - Parsing Running Config

Dec 23, 2012

We just changed  over to Comcast Business and after changing the outside interface to new IP and setting static route. I have access to internet and everythig appears to be good, However asdm will never fully load, alway stuck at 17% or 77%, and I always see "parsing running config".

When I do a show run it will not fully load either, always stop at certain out put. 5 seconds after pulling the Comcast cable out both asdm and running config will load fine.

View 12 Replies View Related

Cisco Firewall :: Basic Config Transparent Mode ASA 5510

Apr 19, 2012

I m trying to set my friewall in my network. The network is very simple. I have my router in 192.168.16.1 255.255.255.0 (mac-address  58-98-35-2a-4c-39) I have my switch in 192.168.16.26 255.255.255.0 (mac-address 00-19-99-5d-1f-43) and i have my firewall ASA between the router and the switch in 192.168.16.250 255.255.255.0 (mac-address 64-9e-f3-ba-28-c9)
 
So i need to configure 3 interface in my ASA.
- OUTSIE e0/0(I call it INTERNET)
- INSIDE e0/1(I call it LAN)
- MANGEMENT m0/0(I call it MANAGEMENT)
 
[Code]....
 
But with this config when I plug the firewall, i dont have access to internet anymore.

View 7 Replies View Related

Cisco Firewall :: 5520 Identity Based Firewall Doesn't Work Using Citric Published

Jul 26, 2012

We are using the newest release of AD Agent (1.0.0.32.1, built 598). The ASA Firewalls 5520 are having the software release 8.4(3)8 installed.When somebody tries to connect thru the Identity based firewalls from a citrix published desktop environment (PDI) the connection is not possible. Checking the ip-of-user mapping on the firewalls (show user-identity ip-of-user USERNAME) mostly doesn't show the mapping of the USERNAME and the PDI the user is logged in. The user-of-ip mapping of the PDIs IP-address shows mostly other users, which then are used to authenticate the acces thru the firewalls.
 
What is interesting, that on the AD Agent using "adacfg.exe cache list | find /i "USERNAME"" i can't see the PDIs IP-address neither because it is mapped to another user.Is Citrix Published Desktop environment supported to connect thru Identity based Firewalls? How AD Agent, Domain Controllers and Firewalls are working together? On the firewalls with "show user-identity ad-agent we see, the following:
 
-Authentication Port: udp/1645
-Accounting Port: udp/1646
-ASA Listening Port: udp/3799
 
Why Cisco does use 1645 and 1646 and not 1812 and 1813?The Listening Port is used for what purpose? we tried the AD Agent modes full- download and on-demand with the same effect.

View 17 Replies View Related

Cisco Firewall :: PIX515 URL Filtering Doesn't Work

Nov 14, 2011

I have one outside interface with global IP address 1.1.1.1 and two inside.Both inside interfaces restrict and non_restrict have private IP addresses.I tried to filter some URLs on PIX515 IOS 7.2, only on restrict interface but my filter does not work.I can access prohibited URL from restrict interface. What's wrong in my URL filtering?
 
Here is my config:
 
PIX Version 7.2(2)
!
hostname pixfirewall
enable password 8Ry2YjIyt7RRXU24 encrypted
names

[code]....

View 1 Replies View Related

Cisco Firewall :: Restored ASA 5505 Now VPN Doesn't Work

Jun 3, 2013

A couple of weeks ago, one of our ASA 5505s failed, and Cisco TAC shipped out a replacement. I was on vacation, and my assistant worked with TAC to get our backed-up configuration restored to the new hardware. This backup was just a copy & paste of the "show start," rather than an export done from ASDM. Anyway, since I got back on vacation I was able to iron out all the wrinkles from the configuration restore, except one. The remote access VPN isn't quite working. This VPN is only used in emergencies, when I can't access that branch office's network via our WAN.
 
What's happening is that clients are getting "authentication failed" messages when connecting. On Windows, it's an error 691. The VPN is set to authentication against RADIUS (Microsoft IAS server). The IAS server reports that the connection and authentication is successful. AAA RADIUS authentication tests on the ASA succeed, as do authentication & authorization LDAP tests. Basically, everything was working fine before we swapped in the new hardware, and I've gone over the configuration with a fine-toothed comb to ensure nothing's changed -- but clearly, I'm missing something. The new ASA is otherwise operating perfectly.

View 3 Replies View Related

Cisco Firewall :: Policy NAT Setting Doesn't Work On PIX 6.3(3)

Nov 30, 2012

I have a server in a network DMZ (IP 192.168.40.43) need to do discovery of other IP address to update the IPAM tool. It should not be done source NAT so I´m trying to use the configuration below with Policy NAT but isn´t working:
 
nameif ethernet1 inside security100
nameif ethernet5 dmz8 security55
!
ip address inside 10.56.12.93 255.255.252.0

[Code]....

It´s following message appears "% PIX-3-305005: No translation group found for icmp dmz8 srv: 192.168.40.43 dst inside: 10.38.36.50 (type 13, code 0)".

View 10 Replies View Related

Cisco Firewall :: 8.2 (ASA5510) / 8.4(2) (ASA5505) - Why Doesn't Route Map / Set IP Next-hop Work

Jan 2, 2012

I need to be able to redirect some HTTP traffic to an Ironport WSA (for now) on a DMZ interface, the initial config I'm trying to test is along the lines of the following (don't have access to the ASA at the moment to cut-and-paste):
 
access-list 101 deny any any neq www
access-list 101 deny tcp host 10.0.2.2 any
access-list 101 permit tcp any any
 
route-map proxy-redirect permit 101
     match ip address 101
     set ip next-hop 10.0.2.2
 
Unfortunately the ASA does not take the "set ip next-hop" command, I get an invalid input error message and if I at the route map config prompt type "?" only the "metric" and "metric-type" commands are listed as available.
 
This happens both on 8.2 (ASA5510) and 8.4(2) (ASA5505). Since others are able to make this work, I assume there's something else on the ASA that I have to set to enable this command?

View 2 Replies View Related

Cisco Firewall :: ASA 5510 NAT Doesn't Appear To Be Working

Mar 8, 2012

I've got an ASA 5510 running 8.4.I have a host on an inside interface, with a static NAT configured on the ASA. The inbound/return half of the NAT doesn't appear to be working. [code] I run a ping from the host (192.168.100.98) to something on the outside (1.2.3.4)Running captures, I can see the outbound ping leaving, having been NATed OK. I can see the reply coming back in to the outside interface with the correct IP address, but I never get the final NATed packet appear on the inside interface. The packet just disappears inside the ASA.

View 2 Replies View Related

Cisco Firewall :: ASA5505 And Asterisk Remote Softphone Doesn't Work

Jan 5, 2012

I have a problem with mi telephony server. My network topology is very simple. I have an ASA5505 connected to Internet throught an ISP. Behind ASA5505 I have a ToIP Server that operate well inside LAN network. However, when I try to register two or more extensions (Softphones) from Internet, Softphones some times it registers sucessfully, but some times doesn´t work.
 
The other hand, when softphones outside from LAN get register sucessfully in Asterisk server, is not possible that one of this calling the other one, and Asterisk server detects them as "UNREACHABLE". I don´t know if the problem are all commands of traffic inspect or if the problem is referenced to a particular UC proxy License.
 
These are configuration lines:
 
object-group service elastix-ports
service-object udp eq sip
service-object udp gt 10000

[Code]......

View 1 Replies View Related

Cisco Firewall :: 5500 Blocking Skype Application Doesn't Work With ASA CX

May 12, 2013

I'm trying to build different content security scenarios for a potential deployment of ASA5500-X series firewall with CX module and ran into a trivial problem. A simple access policy has been configured to deny Skype. It's as simple as it sounds. To my surprise I don't see that it is being enforced.I have all my pending changes committed, events are now showing with hits, see attached print screens. Tried to start Skype on my PC with the source shown on the print screen it and don't see any effects of this policy.
 
As a side note, I know for sure that other type of filtering does work, i.e. I have configured a deny filter for gambling URL category and it seems to work nicely.

View 3 Replies View Related

Cisco Firewall :: ASA5540 In Multiple-context SNMP / Icmp Doesn't Work

Jun 10, 2013

what´s going on with an asa540 configure in multiple-context mode.   I Have a cacti server on my lan and now I´m try to monitoring the interface with snmp. When I try to get this information returns the error message:
 
CISCOASA/CONTEXTA#
JUN 11 2013 01:52:00: %ASA-1-1-6021: Deny UDP reverse path check from 10.6.6.6 to IP_SRV_CACTI on interface inside
JUN 11 2013 01:52:01: %ASA-1-1-6021: Deny UDP reverve path check from 10.6.6.6 to IP_SRV_CACTI on interface inside
 
If I try to ping returns the same error:
 
CISCOASA/CONTEXTA#
 JUN 11 2013 01:56:09: %ASA-1-1-6021: Deny icmp  reverse path check from 10.6.6.6 to IP_SRV_CACTI on interface inside
   
Following attached the conf of my asa   My question is Why I can´t ping or even use snmp ?

View 5 Replies View Related

Cisco Firewall :: FWSM Version 3.2 - No Access-list Line X Doesn't Work

Dec 10, 2011

I am trying to remove a line in a particular access-list configured in a FWSM module using this command "no access-list <acl> line 19 x x x x" but it doesn't work. See below:
 
FWSM/xxx03(config)# no access-list ?
 configure mode commands/options:
  alert-interval  Specify the alert interval for generating syslog message
106001 which alerts that the system has reached a deny

[code]...
 
How can I remove a line from the access-list without clearing the entire access-list?

View 3 Replies View Related

Cisco Firewall :: ASA 5510 Telnet To Outside Mx 587 Not Work

Oct 28, 2012

I can't telnet from a host(Ubuntu 12.10) in our DMZ to an outside MX on port TCP 587. Inspection for ESMTP not enabled. Port 587 enabled for host in DMZ to any.

View 12 Replies View Related

Cisco Firewall :: ASA 5520 CIFS Doesn't Work For Share Folder On Windows Server 2008 R2

Jun 26, 2010

I am using ASA5520 with webvpn for file sharing. But recently we just upgraded the OS that accommodate file shared folder from win2003 R2 32bit to windows server 2008 R2 64bit. Now I have a problem with accessing file share by ASA webvpn, it appears error contacting host, we have tested the file shared of webvpn on the other OS windows 2003 and windows 2008, they are working on these OS except win2008 R2. Current the ASA OS version is 8.0(2). And the windows firewall has been disabed.

View 3 Replies View Related

Cisco Firewall :: ASA 5510 - Can Transparent Mode Use / 30 And Still Work

Oct 9, 2012

I have a ASA 5510 that is connected to my ISP and the inside interface that is connected to my router.  I have a /30 and need to determine if the configuration of x.x.x.121/30 which is my ISP and also the BVI address on the ASA.  The inside router address is x.x.x.122/30 same subnet as my ISP will allow me to pass traffic.  Management interface works using a different ip address but not able to get the traffic to pass traffic out to the internet thru the ASA
 
ISP-------->ASA-------->Router 
 
Bottom Line is that I only have one usable address that is being used by the router and the ISP and ASA are using the other.  Will this work?

View 4 Replies View Related

Cisco Firewall :: Would A 1GB 5510 Memory Stick Work In A 5520

Sep 19, 2012

Are the ASA memory DIMMs created for specific models?  Would a 1GB 5510 Memory stick work in a 5520?

View 1 Replies View Related

Cisco Wireless :: 1140 Doesn't Write To Config.txt File

Nov 8, 2012

My 1140 doesn't write to the config.txt file. I'm not sure why. I have three of these access points that we changed the firmware to make them autonomous. The other two worked fine.

View 1 Replies View Related

Local Area Connection Doesn't Have A Valid IP Config

Jan 24, 2012

Yesterday my internet (Via Cable) was working fine on my desktop, today it keeps telling me
"Local Area Connection" doesn't have a valid IP configuration. My W-Lan works fine, I've replaced the cable with another cable, restarted everything five times over, and even tried plugging the computer directly into a wall.

When I connected my laptop via cable (tried several) It gave me the same error...?

Is there a problem with my router?

View 24 Replies View Related

Wireless Network Connection Doesn't Have A Valid IP Config

Nov 17, 2012

Got randomly dc'd from my router today, tried reconnecting say that its an unidentified network and there's no internet connection; here's the IP config file

Windows IP Configuration
Host Name . . . . . . . . . . . . : CalumFirth-PC
Primary Dns Suffix . . . . . . . :

[Code].....

View 10 Replies View Related

Cisco Firewall :: ASA5510 - Saving Configuration / Insufficient Memory

Oct 3, 2011

When I try to save the configuration it displays the following error.Is it due to insufficient memory?
 
MPF-ASA#wr mem
ERROR: % Unrecognized commandMPF-ASA(config)# wr memBuilding configuration...Cryptochecksum: 81c514b8 9e95ee97 8b512148 b31377a4
[Code]...

View 1 Replies View Related

Cisco VPN :: ASA 5510 - Twice NAT Config

Sep 11, 2011

I'm running into and interesting issue concerning a twice NAT config.
 
We have a remote site that needs to connect to a server cluster on our end.  Using ASDM I have created a NAT rule that uses PAT to map our server addresses to a single IP (this is due to constraints placed on us by the remote site).  This in and of itself shouldn't be a problem.  The issue is that the VPN tunnel won't come up unless I also map an address to the remote site's sever.
 
Example:
Appliance: ASA 5510
ASA Version: 8.4(2)
ASDM Version: 6.4(5)
 
Original Packet:
Source Interface: inside
Destination Interface: outside
Source Address: Server_Cluster
Destination Address: Remote_Server
Service: any
 
Translated Packet:
Source NAT Type: Dynamic PAT (Hide)
Source Address: Mapped_Server_Cluster_Address
Destination Address: Mapped_Remote_Server_Address
Service: -- Original --
 
Within the Translated Packet section, if I set Destination Address to the actual remote server address nothing happens when I attempt to bring up the tunnel.  However, if I map an address to the remote server, the tunnel begins to come up and then fails during phase two (as the mapped address doesn't match the addressing that has been defined in the remote end's connection profile).
 
Initially I thought the issue may be due to an IP addressing overlap since both sites are running similar numbers, but the default route statement on our ASA, should contend with this issue.  Also, each time I change the NAT rule, I change the connection profile to match those changes.
 
So, ultimately, what I wish to accomplish is to allow connectivity between my site and the remote site without having to map another address to their remote server.  How may I do this?

View 2 Replies View Related

Cisco WAN :: ASA 5510 Config For Failover

Aug 2, 2011

We have two offices in the US and one in Mexico. Our site in Mexico connects to our headquarters in the US over an AVPN/ MPLS circuit .Mexico has a separate Internet connection through TelMex. There is an ASA 5510 at headquarters and an ASA 5505 in Mexico. We have a fail over VPN set up in the ASAs for times when the MPLS circuit goes down. All Internet traffic in Mexico is supposed to be routed to the TelMex connection. All company traffic is supposed to be routed to the Cisco router. ASA is supposed to be last resort route. We have a fail over VPN set up in the ASAs for times when the MPLS circuit goes down. (Or at least we did until I had someone work on the configuration)  Everything had been working fine for the last 4 years.
 
Yesterday when the MPLS went down, so did their Internet connection. I realized the Internet traffic is now coming through the MPLs circuit to head quarters and out our ASA. Obviously there is a problem with the configuration. I do not have enough experience to figure this out. I have attached the configs and the routes for both the ASA and the router.

View 11 Replies View Related

Cisco Firewall :: Updating ASA 8.2 To 8.4(5)

Feb 5, 2013

what is the feature option " Proxy ARP on egress interface" used for on the ASA? I'm about to upgrade a ASA from IOS 8.2(1) to 8.4(5) and I am trying to determine if it should be enabled or disabled.

View 6 Replies View Related

Cisco Switching/Routing :: IE-3000-8TC / CLI Vlan Command Does Not Work Inside A Config File

Apr 21, 2013

my environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
 
if i do
 
vlan 12
name NextVLAN
state active
 
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved