Cisco Firewall :: Restored ASA 5505 Now VPN Doesn't Work

Jun 3, 2013

A couple of weeks ago, one of our ASA 5505s failed, and Cisco TAC shipped out a replacement. I was on vacation, and my assistant worked with TAC to get our backed-up configuration restored to the new hardware. This backup was just a copy & paste of the "show start," rather than an export done from ASDM. Anyway, since I got back on vacation I was able to iron out all the wrinkles from the configuration restore, except one. The remote access VPN isn't quite working. This VPN is only used in emergencies, when I can't access that branch office's network via our WAN.
 
What's happening is that clients are getting "authentication failed" messages when connecting. On Windows, it's an error 691. The VPN is set to authentication against RADIUS (Microsoft IAS server). The IAS server reports that the connection and authentication is successful. AAA RADIUS authentication tests on the ASA succeed, as do authentication & authorization LDAP tests. Basically, everything was working fine before we swapped in the new hardware, and I've gone over the configuration with a fine-toothed comb to ensure nothing's changed -- but clearly, I'm missing something. The new ASA is otherwise operating perfectly.

View 3 Replies


ADVERTISEMENT

Dell :: Restored 1545 And Doesn't Detect Wi-Fi Connection?

Jun 30, 2012

I restored my computer from fabric, buy it doesnt recognize the wifi connection

View 5 Replies View Related

Cisco VPN :: L2TP On ASA 5505 Just Doesn't Work?

Nov 20, 2011

Cisco ASA 5505 ver 8.4. Most things work but now I want to setup a vpn connection..I have done this 2 ways, first by using the "VPN Wizard" in ASDM and then 5 hours later removing everything and configuring from cli. And it just doesn't work, client (WinXP & Win7) gets "error 792" and sometimes "error 789" (both indicating problem with phase 1, I'm pretty sure of that) Googling on those gives a few suggestions none works. All I get in the log on Cisco is the "Error processing payload: Payload ID: 1" Google on that only comes up with a few pages telling me this message is caused by an error. (Yeah, I could never have guessed...) For the cli config, I followed this tutorial carefully (3 times actually...) url...I'm using PSK for IPSec, entered same on Cisco and client - checked several times, this is not a password/PSK issue. Ports opened on Cisco: 500, 1701, 4500 (For a try I opened all ports, no change.) And here's the "show run". [code]

View 2 Replies View Related

Cisco Firewall :: 5520 Identity Based Firewall Doesn't Work Using Citric Published

Jul 26, 2012

We are using the newest release of AD Agent (1.0.0.32.1, built 598). The ASA Firewalls 5520 are having the software release 8.4(3)8 installed.When somebody tries to connect thru the Identity based firewalls from a citrix published desktop environment (PDI) the connection is not possible. Checking the ip-of-user mapping on the firewalls (show user-identity ip-of-user USERNAME) mostly doesn't show the mapping of the USERNAME and the PDI the user is logged in. The user-of-ip mapping of the PDIs IP-address shows mostly other users, which then are used to authenticate the acces thru the firewalls.
 
What is interesting, that on the AD Agent using "adacfg.exe cache list | find /i "USERNAME"" i can't see the PDIs IP-address neither because it is mapped to another user.Is Citrix Published Desktop environment supported to connect thru Identity based Firewalls? How AD Agent, Domain Controllers and Firewalls are working together? On the firewalls with "show user-identity ad-agent we see, the following:
 
-Authentication Port: udp/1645
-Accounting Port: udp/1646
-ASA Listening Port: udp/3799
 
Why Cisco does use 1645 and 1646 and not 1812 and 1813?The Listening Port is used for what purpose? we tried the AD Agent modes full- download and on-demand with the same effect.

View 17 Replies View Related

Cisco Firewall :: PIX515 URL Filtering Doesn't Work

Nov 14, 2011

I have one outside interface with global IP address 1.1.1.1 and two inside.Both inside interfaces restrict and non_restrict have private IP addresses.I tried to filter some URLs on PIX515 IOS 7.2, only on restrict interface but my filter does not work.I can access prohibited URL from restrict interface. What's wrong in my URL filtering?
 
Here is my config:
 
PIX Version 7.2(2)
!
hostname pixfirewall
enable password 8Ry2YjIyt7RRXU24 encrypted
names

[code]....

View 1 Replies View Related

Cisco Firewall :: Policy NAT Setting Doesn't Work On PIX 6.3(3)

Nov 30, 2012

I have a server in a network DMZ (IP 192.168.40.43) need to do discovery of other IP address to update the IPAM tool. It should not be done source NAT so I´m trying to use the configuration below with Policy NAT but isn´t working:
 
nameif ethernet1 inside security100
nameif ethernet5 dmz8 security55
!
ip address inside 10.56.12.93 255.255.252.0

[Code]....

It´s following message appears "% PIX-3-305005: No translation group found for icmp dmz8 srv: 192.168.40.43 dst inside: 10.38.36.50 (type 13, code 0)".

View 10 Replies View Related

Cisco Firewall :: Internet Doesn't Work On ASA 5510 For Backup ISP

Feb 15, 2012

I have a ASA 5510. I setup basic configuration to test internet with 2 ISPs. My first line works with out any problem. But my second line doesn't work. Even when i wipe the configuration, and setup only my second isp. Internet doesn't work. Can you tell me if there is anything wrong with this config?
 
CaaaA01#  sh run
: Saved
:
ASA Version 8.3(1)
!
hostname CaaaA01
domain-name example.com

[code].....

View 2 Replies View Related

Cisco Firewall :: L2TP IPsec Doesn't Work On ASA 5510

Dec 21, 2010

I'm trying to setup a L2TP VPN Connection on my ASA 5510 to connect with Android/Windows (Native Clients).I'm using the newest Releases:Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.3(5)
 
My asa config just the interesting part:

crypto ipsec transform-set trans esp-3des esp-sha-hmac crypto ipsec transform-set trans mode transportcrypto ipsec security-association lifetime seconds 28800crypto ipsec security-association lifetime kilobytes 4608000crypto dynamic-map dyno 10 set transform-set transcrypto map vpn 20 ipsec-isakmp dynamic dynocrypto map vpn interface outsidecrypto isakmp enable outsidecrypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400no crypto isakmp nat-traversal

[code]....
 
If i try to connect with a Windows 7 Client (NOT behind NAT) I get the Error 691.
 
I see that Phase 1/2 are working with debug:
Dec 22 16:32:16 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 1 COMPLETED
Dec 22 16:51:25 [IKEv1]: Group = DefaultRAGroup, IP = XXXXXX, PHASE 2 COMPLETED (msgid=00000001)
 
Then I see this "Error":

Dec 22 16:51:26 [IKEv1]: Group = DefaultRAGroup, IP = XXXXX, Session is being torn down. Reason: L2TP initiated
  
I don't understand why it doens't work....I tried many templates from the net but nothings works.

View 5 Replies View Related

Cisco Firewall :: 8.2 (ASA5510) / 8.4(2) (ASA5505) - Why Doesn't Route Map / Set IP Next-hop Work

Jan 2, 2012

I need to be able to redirect some HTTP traffic to an Ironport WSA (for now) on a DMZ interface, the initial config I'm trying to test is along the lines of the following (don't have access to the ASA at the moment to cut-and-paste):
 
access-list 101 deny any any neq www
access-list 101 deny tcp host 10.0.2.2 any
access-list 101 permit tcp any any
 
route-map proxy-redirect permit 101
     match ip address 101
     set ip next-hop 10.0.2.2
 
Unfortunately the ASA does not take the "set ip next-hop" command, I get an invalid input error message and if I at the route map config prompt type "?" only the "metric" and "metric-type" commands are listed as available.
 
This happens both on 8.2 (ASA5510) and 8.4(2) (ASA5505). Since others are able to make this work, I assume there's something else on the ASA that I have to set to enable this command?

View 2 Replies View Related

Cisco Firewall :: ASA 5505 Doesn't Start

Feb 28, 2013

I write because my Cisco ASA 5505 doesn't start.When I connect power to the device, immediatly "Power" green Led turn on but "Status" Led is orange and not change.There is not data by Console cable.I try by another Power Supply but nothing.

View 1 Replies View Related

Cisco Firewall :: ASA5505 And Asterisk Remote Softphone Doesn't Work

Jan 5, 2012

I have a problem with mi telephony server. My network topology is very simple. I have an ASA5505 connected to Internet throught an ISP. Behind ASA5505 I have a ToIP Server that operate well inside LAN network. However, when I try to register two or more extensions (Softphones) from Internet, Softphones some times it registers sucessfully, but some times doesn´t work.
 
The other hand, when softphones outside from LAN get register sucessfully in Asterisk server, is not possible that one of this calling the other one, and Asterisk server detects them as "UNREACHABLE". I don´t know if the problem are all commands of traffic inspect or if the problem is referenced to a particular UC proxy License.
 
These are configuration lines:
 
object-group service elastix-ports
service-object udp eq sip
service-object udp gt 10000

[Code]......

View 1 Replies View Related

Cisco Firewall :: 5500 Blocking Skype Application Doesn't Work With ASA CX

May 12, 2013

I'm trying to build different content security scenarios for a potential deployment of ASA5500-X series firewall with CX module and ran into a trivial problem. A simple access policy has been configured to deny Skype. It's as simple as it sounds. To my surprise I don't see that it is being enforced.I have all my pending changes committed, events are now showing with hits, see attached print screens. Tried to start Skype on my PC with the source shown on the print screen it and don't see any effects of this policy.
 
As a side note, I know for sure that other type of filtering does work, i.e. I have configured a deny filter for gambling URL category and it seems to work nicely.

View 3 Replies View Related

Cisco Firewall :: ASA 5510 - Saving Config Via Scp Doesn't Work After Updating To 8.24

Apr 5, 2011

since our update of Cisco ASA 5510 (active/standby cluster) from version 8.22 to version 8.24 it isn't possible to transfer files from/to a sftp client. The request just times out. SSH from this client is possible.

[Code]...

View 2 Replies View Related

Cisco Firewall :: ASA 5505 - Back ISP Connection Doesn't Up?

Feb 27, 2011

I have asa 5505 with security plus license, I configured dual ISP with two different ISP provider. I followed below cisco document to configure dual ISP [URL] The Configuration works during the testing, while removing the primary ISP cable from firewall. The problem i am facing is my primary ISP is down but the gateway is still up and it not switch over to backup ISP. For SLA which IP should i monitor so once my primary ISP is down it will fallback to Secondary.

View 5 Replies View Related

Cisco Firewall :: ASA5540 In Multiple-context SNMP / Icmp Doesn't Work

Jun 10, 2013

what´s going on with an asa540 configure in multiple-context mode.   I Have a cacti server on my lan and now I´m try to monitoring the interface with snmp. When I try to get this information returns the error message:
 
CISCOASA/CONTEXTA#
JUN 11 2013 01:52:00: %ASA-1-1-6021: Deny UDP reverse path check from 10.6.6.6 to IP_SRV_CACTI on interface inside
JUN 11 2013 01:52:01: %ASA-1-1-6021: Deny UDP reverve path check from 10.6.6.6 to IP_SRV_CACTI on interface inside
 
If I try to ping returns the same error:
 
CISCOASA/CONTEXTA#
 JUN 11 2013 01:56:09: %ASA-1-1-6021: Deny icmp  reverse path check from 10.6.6.6 to IP_SRV_CACTI on interface inside
   
Following attached the conf of my asa   My question is Why I can´t ping or even use snmp ?

View 5 Replies View Related

Cisco Firewall :: FWSM Version 3.2 - No Access-list Line X Doesn't Work

Dec 10, 2011

I am trying to remove a line in a particular access-list configured in a FWSM module using this command "no access-list <acl> line 19 x x x x" but it doesn't work. See below:
 
FWSM/xxx03(config)# no access-list ?
 configure mode commands/options:
  alert-interval  Specify the alert interval for generating syslog message
106001 which alerts that the system has reached a deny

[code]...
 
How can I remove a line from the access-list without clearing the entire access-list?

View 3 Replies View Related

Cisco Firewall :: 5505 Doesn't Recognize Ip Address Dhcp

Apr 16, 2013

my 5505 running on version 8.2.5 doesn't seem to recogize the simple command "ip address dhcp setroute......"
 
ciscoasa(config-if)# ip address dhcp
^
ERROR: % Invalid Hostname
ciscoasa(config-if)# ip address ?  
 
configure mode commands/options:  Hostname or A.B.C.D  Firewall's network interface address

View 7 Replies View Related

Cisco Firewall :: ASA 5505 Doesn't Reset To Factory Default?

Jun 20, 2011

Why when I try to reset Cisco ASA 5505 by pressing  the button behind the hardware nothing happen? Just via software I can reset it?
 
I bought the hardware an year ago and I've never used, the problem that I don't have the blue cable and via software connecting to PC doesn't work.

View 6 Replies View Related

Cisco Firewall :: ASA 5505 Doesn't Forward Incoming Connection To LAN

Jun 13, 2012

I just got a Cisco asa 5505 with the next OS and ASDM info ASA 5505 OS 8.4(3) ASDM 6.47 I configured and enter all rules to allow incoming traffic to LAN but it's not working also, I have one host inside that is configured in a second IP and create the rule to allow traffic to it but it doesn't work too.

Problem 1 I have VNC running in port 5900 tcp and I want to connect from Internet using port 6001 and this has to forware the connection to the real VNC port. In the configuration I have a few host with the same configuration but I use different outside port to get it.
 
Problem 2. I have a second IP with services: SMTP, HTTP, HTTPS and port 444 all TCP forwarding to a server in the LAN.
 
Facts: SMTP. Every time that I do telnet to the second IP looking for the SMTP port, the firewall doesn't let the incoming connection goes through and the LOGGING screen doesn't how that connection.PORT 6001 (outside)this port is configured to work with the IP in the outside internface and it was to send the incoming connection to a host inside to the real port 5900.Can any one check my configuration if I'm missing anything? for sure I'm but I didn't find it. Bellow is the configuration, I masked the Public IPs just left the last number in the IP, also I left the LAN network to see better the configuration.
 
CONFIGURATION.
: Saved
:
ASA Version 8.4(3)
!
hostname saturn1
domain-name mydominio.com
enable password SOMEPASS encrypted

[code]....

View 4 Replies View Related

Cisco Firewall :: 5505 Transparent Mode Doesn't Pass Traffic

Dec 4, 2012

  asa 5505 do not pass traffic as a patch cord, how to make it pass traffic? [code]

View 2 Replies View Related

Cisco Firewall :: ASA 5505 Doesn't Allow Local Provider SMTP Traffic

Aug 7, 2011

We are using several Cisco ASA 5505 with the 8.05 OS on it. The problem is that the SMTP traffic of my ISP(Telenet) isn't passtrough the ASA, I'm using outlook 2010. Before there was also a problem with our local exchange server but I solved this by disabling ESMTP checking in the policies, but it didn't worked for my local ISP.

View 4 Replies View Related

Cisco Firewall :: ASA 5520 CIFS Doesn't Work For Share Folder On Windows Server 2008 R2

Jun 26, 2010

I am using ASA5520 with webvpn for file sharing. But recently we just upgraded the OS that accommodate file shared folder from win2003 R2 32bit to windows server 2008 R2 64bit. Now I have a problem with accessing file share by ASA webvpn, it appears error contacting host, we have tested the file shared of webvpn on the other OS windows 2003 and windows 2008, they are working on these OS except win2008 R2. Current the ASA OS version is 8.0(2). And the windows firewall has been disabed.

View 3 Replies View Related

Cisco Firewall :: ASA 5505 SSL / HTTPS / ASDM Won't Work / Cipher Fail

Nov 21, 2010

Does my device not support enough encryption to get ASDM/SSL/HTTP working?
 
First time I've ever seen this...: 
 
%ASA-7-609001: Built local-host inside:192.168.1.10 %ASA-7-609001: Built local-host identity:192.168.1.1 %ASA-6-302013: Built inbound TCP connection 13 for inside:192.168.1.10/61194 (192.168.1.10/61194) to identity:192.168.1.1/443 (192.168.1.1/443) %ASA-6-725001: Starting SSL handshake with client inside:192.168.1.10/61194 for TLSv1 session. %ASA-7-725010: Device supports the following 1 cipher(s). %ASA-7-725011: Cipher[1] : DES-CBC-SHA %ASA-7-725008: SSL client inside:192.168.1.10/61194 proposes the following 11 cipher(s). %ASA-7-725011: Cipher[1] : DHE-DSS-AES256-SHA %ASA-7-725011: Cipher[2] : AES256-SHA %ASA-7-725011: Cipher[3] : DHE-RSA-AES256-SHA %ASA-7-725011: Cipher[4] : DHE-RSA-AES128-SHA %ASA-7-725011: Cipher[5] : DHE-DSS-AES128-SHA %ASA-7-725011: Cipher[6] : RC4-MD5 %ASA-7-725011: Cipher[7] : RC4-SHA %ASA-7-725011: Cipher[8] : AES128-SHA %ASA-7-725011: Cipher[9] : EDH-RSA-DES-CBC3-SHA %ASA-7-725011: Cipher[10] : EDH-DSS-DES-CBC3-SHA %ASA-7-725011: Cipher[11] : DES-CBC3-SHA %ASA-7-725014: SSL lib error. Function: SSL3_GET_CLIENT_HELLO Reason: no shared cipher %ASA-6-302014: Teardown TCP connection 13 for inside:192.168.1.10/61194 to identity:192.168.1.1/443 duration 0:00:00 bytes 7 TCP Reset by appliance %ASA-7-609002: Teardown local-host inside:192.168.1.10 duration 0:00:00 %ASA-7-609002: Teardown local-host identity:192.168.1.1 duration 0:00:00

View 7 Replies View Related

VPN Doesn't Work Properly?

Jan 11, 2011

I have an problem with VPN connection on notebooks. Sometimes the VPN connection works perfectly, and other times it just doesn't work at all.The Cisco VPN client software is version 5.0.04.0300. Operating system is Windows XP Prof SP2.When the connection fails, the client statistics window shows "Bytes Received: 0".Rebooting the system, has no effect

View 1 Replies View Related

New Share Doesn't Work

Jan 27, 2011

Normally, when one right clicks on a drive letter having opened 'My computer', then select 'Sharing' there is a warning about sharing a whole disk and the option to accept anyway.One laptop doesn't offer that. It just shows the admin share of C$ immediately. If I choose 'New' at the bottom of the panel a new drive letter and drive name can be entered but it can never be accessed over the network! It shows up in the workgroup but I get a network error 'Network path not found' if I try to access it. I can ping the laptop from anywhere by name and IP address.The laptop can access all the other PCs without any problem.

View 12 Replies View Related

Cisco :: LMS 4.2 Syslog Collector Doesn't Work

May 21, 2013

my LMS 4.2, syslog collector on LMS doesnt working even service syslog collector running normaly and also i saw in syslog_info is working to collect syslog from all router but not show up in dashboard monitoring.I have setting on every router to logging (ip address LMS) but on LMS no any syslog from router can collect.i did a selftest from LMS there are all PASS except nslookup fail, it is has relation with syslog not show up on dashboard?

View 5 Replies View Related

Cisco Wireless :: Air-AP1142-e-k9 Doesn't Work With 802.11n?

Jun 29, 2012

I bought cisco AP (air-ap1142-e-k9) and we know this ap works with 802.11a/g/n same the description note on the package cartoon but my problem is when i configure that ap its work only with 802.11a/g i tries to make it works with 802.11n but fail .

View 3 Replies View Related

Cisco WAN :: 881 3G Won't Work - Doesn't Receive IP Address

Jan 26, 2011

I'm trying to configure Cisco CISCO881G-K9 3G router to connect to mobile network without success. The cellular interface gets up but it doesn't receive IP address. It seems that profile isn't activated and it should've been.
 
I've attached running config and some other information gathered from router.

View 7 Replies View Related

Internet Doesn't Work On Desktop?

Mar 11, 2011

So, my desktop, running windows 7, can no longer connect to the internet. It has no problem connecting to the router, but it will not receive packets. I double checked my connection using my laptop and it works with wireless and wired connections, so I know it's something with my desktop. I would really like to avoid doing a reinstall, I don't have anywhere to back my data up to.

View 5 Replies View Related

Wireless Doesn't Work When Main PC Is On

Jan 16, 2012

Whenever my main PC is turned on, i get no signal from the wireless, like i cannot use my phone or laptop on the internet i use an Ethernet cable which is directly connected to my main PC my windows is also window XP and my modem model is TG782T only if my PC is turned off the wireless works

View 2 Replies View Related

Internet Doesn't Really Work Unless VPN Is Connected?

Aug 17, 2011

I have been having problem with my internet lately. I live in UK and there is this game that I used to play that has a region IP block so I have to use Hotspot shield to play,but now my internet doesn't connect to Hotmail or this forum unless hotspot shield is turned on. How can I fix that? I tried config/flushdns but no luck. I am using window xp.

View 1 Replies View Related

Laptop Doesn't Work Wirelessly

Sep 20, 2012

We have recently switched routers and now my laptop doesn't work wirelessly; it connects to the router but there isn't an internet connection. The laptop works fine when the LAN cable is plugged in though. Our other laptop can connect to the internet with or without the LAN cable. Both are Toshibas running on Windows Vista.I have tried various approaches such as downloading the latest Atheros AR5007EG drivers but it said that they're already the most up to date. [code]

View 5 Replies View Related

USB Wireless Adapter Doesn't Work?

Jun 16, 2011

I purchased a used Compaq laptop with a Realtek USB wireless adapter. The laptop came with XP Pro. I connected the adapter and everything worked great. My husband got a virus I couldn't remove. I have the CD for XP Home so I did a clean install.Windows works fine. I connected the USB wireless adapter and ran the installation disk. When I open Realtek to connect nothing appears in the available networks. I checked the device mgr and it says Realtek is working. I turned off my 2Wire gateway and then reconnected it. I doubled checked that the Windows wireless utility is disabled. Still no available networks. Everything was fine before the reinstall of Windows XP Home.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved