Computer Not Accessible From Server By Name?
Mar 19, 2011
I'm working on a small network (1 server, 6 workstations, stand-alone, not connected to the main Company Network) "reinstalling" a Workstation. Re-imaging from semi-generic Norton Ghost image (4 of the 6 Workstations run the same programs with different addresses). I then had to reset the IP, the Computer Name, and then the Domain (I did it in that order).
I'm using Windows Server 2003 as the domain controller, and the Workstation is Xp Pro Sp 2.
The Workstation is using the same IP, Name, User as before, and they were working with the server previously (a program had corrupted prompting the reinstall).
The problem is that if I open windows explorer and type in the Workstations IP (\000.00.0.1) I get access to the computer. But if I go there and type in the Workstations Name (\Computer01) I get a "you may not have permission to use this network resource" error.
If I go to the work station, and try the same thing except with the Server's IP (\000.00.0.100) and Name (\Server01) I get access.
This Workstation controls an I/O device that is used by a program running on the server (most of the time, not while I'm doing the install of course) and the program uses the Workstation's Computer Name to access it.
As far as I can tell all the settings on this Workstation match the 3 that are running the same programs, but I could have missed something.
I'm a bit stumped by this, I don't normally deal with the Server side of the computers. I usually just set up the workstations to whatever Name/IP the Net-admins give me. But my bosses put me in charge of this little network, mainly because the Net-admins din't want to deal with it.
View 2 Replies
ADVERTISEMENT
Aug 15, 2012
I have a Windows 7 machine that is wired to the router. I have Windows XP computer that is wireless in another room. Signal is showing 80% and internet is accessible and fast from both systems; but, I cannot access either computer from the other computer. I got the IP addresses of each machine and I cannot ping from either direction. Firewalls are turned off on both systems.When I type in \server, I get an error that say I should check my spelling or use the windows Search; but, that doesn't work.
View 5 Replies
View Related
Mar 1, 2012
I recently change routers to a Linksys E3000 wireless router from a Uverese 2wire residential gateway and all worked well for a short time nothing changed however when I go to view network devices from Win7,Vista or XP computers the network devices are no longer there. when I shut down and reboot the router and switches I still cannot see these devices, however when I hook up my old 2wire router I see my devices again. Even when I reconnect to the E3000 all the devices can be viewed for a few hours. Changing routers resets something but maybe overloads the linksys E3000 after a few hours? maybe this E3000 is just defective?
When I view a network map in Network & Internet all the devices appear in the map The configuration is Linksys E3000 router with two (2) 8 port Trendnet gigabyte switches and One (1) 8 port Trendnet Poe 10/100 switch. They are chained router to 8 port gig to 8 port gig to 8 port Poe 10/100. Prior to this I had the router to each switch separately - - this does not seem to matter works the same either way
Devices attached - Network printer,XP desktop, Vista Desktop, NAS, WDTVlive media player, Roku, Home automation controller, IP touch screen for the automation, security DVR (wireless devices are all ok Win7 laptop, Vista laptop, Ipad)seldom are more than 3 devices being used at one time light traffic.)
View 2 Replies
View Related
May 21, 2011
I have a question that�s been bugging me and that internet searches didn�t quite explain and that is how do I make a resource available publicly e.g. web serverAll I hear so far is register a domain name but that doesn�t quite answer the full question. Id like to know exactly what happens when a user types in the url of my web site and how their traffic gets to me. Is it.. get a static ip from my isp then provide this to the domain name registrar and that it now every one can access my site?? Seems to simple.
View 1 Replies
View Related
Mar 23, 2013
I have nated my 172.81.15.0 255.255.255.0 into my internal server 10.1.10.164 , i can ping the out side server but the internal server is not accessible from out side static (Database-Servers,interface-sms) 172.81.15.2 10.1.10.164 netmask 255.255.255.255icmp permit 172.81.15.0 255.255.255.0 interface-smsroute zemen-sms 172.81.15.0 255.255.255.0 10.131.199.201 1access-list Database-Servers-in extended permit tcp host 10.1.10.164 host 10.185.62.144 eq 9090access-list Database-Servers-in extended permit tcp host 10.1.10.164 host 10.185.62.144 eq wwwicmp permit host 10.185.62.144 interface-smsi can ping the out side server 10.185.62.144 with out a problem . from the server 10.185.62.144 i can ping untill 172.81.15.2 and it will not ping the natted server 10.1.10.164. as u seen the accesslist ping is permitted.
View 1 Replies
View Related
Oct 7, 2012
In my client office, We have replaced small business router cisco RV042 with Cisco ISR router 2911, in that router we have configured NAT to allow internal user to access internet and port forwarding for outside user to access web servers and other application that are hosted internally.
we are not able to access [URL] (name changed) from internally and one of the application that are runnning on port no. 8280., and same is working properly from outside the network.other application that running on 8287 is accessible form internally.
We are accessing with ip address http://192.168.1.51:8280. and [URL] not working from inside.
But all works fine with old cisco RV042.
View 9 Replies
View Related
May 24, 2010
I`ve had a problem with my WAG320N for some time now.I`ve add a 1,5Tb hard drive to the usb and I can access it at LAN.Now I want to take it a bit further and be able access it from the outside.
View 9 Replies
View Related
Mar 26, 2012
I have a domain with a domain controller Server 2003. I have a backup dc running an application with server 2008. The shared folder I am trying to access is on an nt server 2000. We have had a mapped drive "I:" and have used it for years. Our copier also scans to a shared folder on the server 2000 machine. All of the desktop systems are xp sp3 with one W7 machine. A couple of weeks ago when user attempted to access the shared/mapped drive, an error would occur that "the drive was in use and they could not be logged on". Sometimes the error would say "you don't have permission to access the drive." Mind you no settings have been changed on the network. When either of these errors would occur it would occur for everyone but if I rebooted the server everyone could connect again. The same errors would occur the next day or 6 - 8 hour later. Now the error has occured "Drive is already in use and you cannot be logged in" (I have tried drive Z as well the drive is not in use) and restarting the serever no longer works. No one can access the shared drive. I have unmapped the drive on my system and have attempted to reconnect, I enter the path and check reconnect at logon and it asks for a password. I enter the administrator password (which is what I always used) and it just pops right back up asking for a password as if I entered nothing. I can ping the server with the shared folder and even logon remotely so I know it is not a physical disconnect. I am not sure what changed and have followed many suggestions found to no avail. We cannot access the shares or scan.
View 1 Replies
View Related
May 8, 2012
My web server was down for the day now it's back on but the ASA not accessible with error drop rate-1 exceed
View 3 Replies
View Related
Jun 15, 2011
I have an old computer that is currently running XP at 2.1GHz Athlon AMD with 1.5 DDR RAM, would I be able to turn it into a dedicated server? More importantly, should I? all I have is a small home network running a couple desktops and a printer off one and connected by a wireless router to the internet, would it make a difference at all in processing speed or connectivity on any of them?
View 2 Replies
View Related
Jan 7, 2013
How to create a small computer lab. I own a private tutoring class and i want to expand into computer programing. I am planning on purchasing about 10 computers to begin with. However, i want go create a small server so that each student has their own log in id# and all their files are only accessed when they log in. I just want to find out how i would be able to do this as ive seen this at public schools.
View 1 Replies
View Related
Jun 22, 2012
I have two server computers. there IP addresses are:
1. 192.168.0.99
2. 192.168.1.99
Now, how to configure it for accessing data from each other?
View 7 Replies
View Related
Jun 16, 2011
I have an old computer that is currently running XP at 2.1GHz Athlon AMD with 1.5 DDR RAM, would I be able to turn it into a dedicated server? More importantly, should I? all I have is a small home network running a couple desktops and a printer off one and connected by a wireless router to the internet, would it make a difference at all in processing speed or connectivity on any of them?
View 6 Replies
View Related
Feb 22, 2011
System was running fine untill about two days ago. File and print sharing stop working. went to services and tried to restart "Computer Browser". It would not start due to a dependancy. Tried to start "Server Services" Got the following error. "Can not start Server Service on local computer, Error 2:The system cannot find the filed specified". The files srvsvc.dll 95KB 4/14/2008 The file srv.sys 327KB 4/14/2008.If I delete either of these files they are just created again. If I replace them with the new versions they are converted back to these files.I am running XP Pro SP3.
View 3 Replies
View Related
May 2, 2012
I work in a small group with a network server so we can share files and documents from computer to computer. I am trying to access this server on a new computer and am not having any luck finding instructions on how to do so. I don't need to sign in to the network (to gain access to internet browser, etc), I need to be able to add this computer to our server so I can view these folders & files on this new computer.
View 2 Replies
View Related
Feb 10, 2012
need to know why I can not connect to the internet after I am done downloading windows Xp on my Desk top. I got an error message from the cmd, saying that computer is unable to contact DHCP server.
View 1 Replies
View Related
Nov 21, 2011
I am just wondering how to set up a home network with an old computer used as a server... we will have a wii, ps3, lap top, and 2 desktops connected to the network as well as two dell printers. The laptop runs windows XP and the desktops run windows vista. The old computer will will use as a server is windows xp or windows 98 (most likely wont use that computer). What will i have to do to set this up and run the server as well as the network.
View 9 Replies
View Related
May 1, 2011
I get this message when trying to connect to server the remote computer is not available on the network.ISP provider was changed so was IP address.
View 8 Replies
View Related
Mar 20, 2013
how can I change a computer from one network to other in order to use FTP server
View 4 Replies
View Related
Apr 29, 2012
I have an ASA5510 connected to a computer running Windows 7 (the NTP Server) on its "inside" interface.Using the ASDM, I have configured the ASA5510 to use the Windows 7 as its NTP server (my architecture forces me to use a local machine as an NTP server):
-IP address: 192.0.99.1 (the ASA5510 has an IP address of 192.0.99.40)
-Interface: inside
-Key number: None
-Enable NTP authentication: no.
I have other Windows computers on the "inside" interface using the NTP Server, so NTP traffic is relayed without any problem. But somehow, the ASA5510 is not able to synchronize with the NTP Server.I see the following log entry:
-Source IP: 192.0.99.1
-Source Port: 123
-Destination IP: 192.0.99.40
-Destination port: 65535
-Description: Teardown UDP connection 3905 for inside: 192.0.99.1/123 to identity: 192.0.99.40/65535 duration 0:02:01 bytes 96
so it seems like the ASA5510 sends a request to the NTP Server, but I am not sure whether the reply doesn't get processed correctly, or the connection stays open too long (my UDP connection timeout is the default, 2 minutes).
I had trouble getting SonicWALL NSA2400s to use Windows 7 devices as NTP servers. I had to get a firmware version where there was no MD5 authentication (which I think is OK in this case), and change a setting in the Windows registry (HKEY_LOCAL_MACHINE/SYSTEM/CurrentControlSet/services/W32Time/Config/AnnounceFlags: from 0xa to 0x5)
View 5 Replies
View Related
Jan 21, 2013
Used to access the FTP server using "My computer" as some reason we cannot use the IE explorer to direct access...However, under the Windows 8 enviornment, it just prompt out "No Such Interface Supported" and cannot direct open the file... but only can copy/copy to folder etc...
View 1 Replies
View Related
Jul 18, 2011
My network connection was vanish the client are not connected to server and the computer cannot access internet
View 1 Replies
View Related
Aug 26, 2011
We have a network setup on a Domain. Yesterday all computers were talking to one another correctly and were visible. We had a Linksys e1500 Wireless router when everything was running smoothly. We upgraded to a Linksys e3200 and swapped it into the system pulling the e1500 out.
No settings or configurations were changed on the server or any of the client machines, but as soon as the e3200 was installed and put in place all client machines on the network were visible to one another but the server was not.
After scratching my head and not having a suitable answer I decided to just put the e1500 back into our infrastructure and remove the e3200. Imagine my dismay when the server was still missing but all other computers were visible on the domain. Obviously the e3200 wasn't and isn't the issue, but it was literally the only change we made to our system in that period between... visible server and no visible server.
Anything I can check for a server running Windows Server 2008 R2 Standard that has mysteriously vanished without explanation when it has been working fine for 4 weeks prior without fault?
View 1 Replies
View Related
Sep 22, 2012
currently i have my server computer in room a, and i have 2 computers in room b. my current setup is.Server---ethernet cable-----router-----modem, for the computers in room b, the setupis.......computers-------ethernet router----ethernet wire-----router----modem.if i remove the switch in room b, then the computer in room b can communicate with the server computer, if i keep the ethernet router then i cant connect to my server. i need the computers in room b to be wired but there is only 1 wire in the room, so that is y i added the ethernet router. how can i get the server to connect to the computers in room b with the ethernet router?
My main wifi router is a Asus N66U
My ethernet router is a dlink dir 130
View 1 Replies
View Related
Apr 23, 2011
I have configured a my desktop as a domain controller with server 2008..with dns service running on it. When i tried adding another desktop to this domain, i get the following error message
"Troubleshooting network identification Error: This computer successfully resolved the Domain Name System (DNS) service (SRV) resource record required to locate a domain controller, but it failed to locate a domain controller for the Active Directory domain displayed in the error message.
Cause: The required A (address) resource records that map the name of the domain controller to its IP address do not exist in DNS.
Solution: Verify that the required A resource records do not exist in DNS by using the Nslookup command-line tool.
See also: To verify that A resource records exist in DNS. Cause: The domain controller advertised in DNS may not be connected to the network or is connected to the network but is not running.
Solution: Verify connectivity and then verify that the domain controller is running.
See also: To test a TCP/IP configuration by using the ping command; DNS requirements for joining an Active Directory domain."
View 7 Replies
View Related
Jun 20, 2011
I have this idea of using my old computer (which is still pretty awesome) as a back up + production server. What this would entail would be that each person in my house has a dedicated hard drive that auto-syncs folders they've selected for backing up (not Memeo under any circumstances!). Then there will be a hard drive for me to work on web projects on. I'd like this computer to be very secure but if needed, I could show my work on the production drive to my boss.
View 6 Replies
View Related
Feb 26, 2013
We have a Comcast business class cable modem with a static IP address. There are two devices hardwired to it; a server and a Linksys WRT610N, The server is hardwired to it with port forwarding set for ports 21, 80 and 5900. It works perfectly and can be reached as intended by the outside world but not by our own network. Our Linksys WRT610N is hardwired to the modem. All computers on the wireless network see each other and can access the internet perfectly. So all seems well enough. BUT, no computer on our network can reach our server. Using the domain name or VNC connections from inside our system results in time outs and no connection.
View 12 Replies
View Related
Apr 14, 2011
At my office we have a dell server running windows small business server 2003, there are around 15 computers on our network running mostly windows 7 (a few with XP). I am wondering how difficult it is to add a computer to the network so it can log into our domain and all that.I just had to reformat one of the computers and would normally wait for our network guy to do it remotely but If i could do it myself it would save time (and money). I am already an administrator and basically i just need to make it so the log in prompt when windows starts has our office network listed as the domain instead of jus the local log in. It is a dell running windows 7 64 bit.
View 5 Replies
View Related
Mar 16, 2011
I have redirected the IE Favorites folder to our network but I need a script to copy the Favorites to the new location.
View 2 Replies
View Related
Jul 8, 2011
My old dLink DIR-655 router could serve as an NTP server for all the computers on my network. It would get the time from the dLink NTP time source and allow me to sync all the systems on my home network off the DIR-655.
I had to replace it with this new E4200 but don't see an option for it to act as a time source for my internal network.
Can this router be used for this function?
View 1 Replies
View Related
Jan 12, 2012
I have a network that is currently set up in the following way:Modem -> vonage Motorola router -> wireless router Most computers are hard wired to the Motorola router. Some other ones connect via the linkseys wireless router. All computers are able to connect to the Internet. The problem I have is that I will be setting up a home computer as a file server connected to the Motorola router. The network acts as though it is two meaning that computers on one router can't see computers on the other router. What steps should I take in order to make all computers accessible through both routers.When I type 192.168.1.1 from a computer on the Motorola router, I get nothing, when I type in my actual ip address, I get the Motorola router. When I type in 192.168.1.1 from a linkseys connected computer, I get access to the linkseys router.
View 3 Replies
View Related
May 7, 2012
I bought a new WRVS400n recently because it had Gigabit speed, wireless n and a built in VPN server. The device works perfect except for the Quick VPN client. I'm a system engineer so I thought I could set it up quite easy just like any other device I configured in the past. Painfull but it isn't like this.
I set up the VPN on the WRVS4400n and generated a certificate. I saved both the client and admin certificate to my pc, I gave them a name to easily make up the difference between both of them. When placing the certificate in the installed QuickVPN folder, it doesn't seem to get recognised by the QuickVPN software. When I try to connect, it says 'Server's certificate doens't exist on your local computer'. I guess the naming convention must meet some kind of format, is that correct? If so, this should have been described in the documentation.
Besides that I checked if the required ports used by the VPN server are open on the public port of the device, that is the case. So It seems I'm quite close to get it working.
The version of QuickVPN I used is 1.4.2.1. The WRVS4400n has the latest firmware loaded.
View 1 Replies
View Related
Mar 9, 2012
Ok so one site i used to use regularly has for the last few month been either incredibly slow or totally inaccessible. Its a perfectly sedate site just a social forum, its this one. www.pandemoniumcarnival.com/ which is accessible to all my friends but seemingly not to me...So far i have changed DNS (to open DNS and Google, thinking my isp had blocked it for some reason)Tried Firefox (my usual browser) chrome, IE ...flushed all the settings etc in each no cookies etc. Tried "In Private Browsing" etcOddly i can get to the site if i use a site called "Hide my ***" a proxy server thing. But even then its not fully functioning due i think to the proxy setting (?)
View 8 Replies
View Related
