Cisco WAN :: 1811W Connection Won't Come Up
Jul 24, 2011
Cisco 1811 device. Working great with connection from TWTELCOM, trying to add 2nd connection from BRTHOUSE set SLA's and metrics but config still isn't working. The connection won't come up and when I do show ip route ip address it doesn't show a metric so neither connection has a priority and the connection fails. I want brighthouse to have priority as shown with SLA's but if brighthouse fails I want it to go back to twtelcom. [code]
View 1 Replies
ADVERTISEMENT
Nov 8, 2011
I have a Cisco 1811W that after several years in service suddenly stopped allowing any wireless connection to laptops on the domain. It allows hard wired connections and devices that are just using the wireless hot spot like iPads and Iphones but not devices on the domain. These same laptops connect wirelessly without issue at our other facilities which use the same hardware.
Here is the config file of the router in question...
router#show run
Building configuration...
Current configuration : 11776 bytes
[Code].....
View 2 Replies
View Related
Oct 19, 2012
I am having a hard time connecting my router into a internet modem since my modem is giving its own private ip address in short the modem is a router in itself. in addition, I cant change the modem's dchp pool its fix with 192.168.1.0 network.
View 3 Replies
View Related
Jan 9, 2011
I am attempting to configure DDNS on an 1811W, but my configuration fails. Apparently,it is not connecting to the TZO server, because when I run <show ip ddns update> in telnet, the message "update destination not available, although rh.tzo.com can be pinged. I am attaching a copy of the config file. the ip name-server entries are my IP DNS, and the url/user name/ key entry was provided by TZO support.
View 3 Replies
View Related
Dec 4, 2011
I have an 1811w router and can not figure out how to access the settings of the router. I do not have a console port that I can use to access the settings that way so I want to know how to do it using the SDM. I thought I was following the directions but for some reason when I connect my computer to one of the routers LAN ports no connection is recognized on either the router or the computer. How do I go about connecting to the router and accessing the settings?
View 1 Replies
View Related
Apr 25, 2013
I have some problem to get working ACLs. The main purpose of this ACLs is to control what is going out from vlan to internet. (For example, i want that only my proxy can access to the web.) So, i use Cisco Packet Tracer and test new rules in lab without any problem.
interface Vlan1
ip address x.x.x.x x.x.x.x
ip flow ingress
ip flow egress
ip nat inside
[Code]...
But it doesn't work on my Cisco 1811w and i dont uderstand why and i'm not sure to have sufficient knowledge to aolve my problem by my own.
View 10 Replies
View Related
Nov 11, 2012
We have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I am running
WCS 7.0.230.0
WLC 5508 (same code)
View 3 Replies
View Related
Dec 16, 2010
I am using a 1811W and CCP for configuration. I am trying to assign client names to devices on the LAN so that when a network scanner is used, the client name is displayed. I have attached part of the running config after a binding has been done. My assumption is that the scanner should now show 192.168.1.109 as name <Supermicro>, but the name is blank. Is this configured correctly for what I am trying to acheive?
View 3 Replies
View Related
Mar 2, 2009
Need basic wireless configuration for a SOHO Cisco 1811W router? I just need the wireless to connect to the base wired LAN - with both WEP and MAC authentication. And - can the MAC auth. parameters be configured via CLI and not have to use either SDM or CP? I can access the router via SDM - but the Wirless Application will not fire up - and CP doesn't work at all.
View 18 Replies
View Related
Mar 19, 2013
Cisco 1811W router, IOS 15.1(4)M6, DHCP server not working on internal VLAN but configuration looks OK to me. [code]
View 1 Replies
View Related
Oct 19, 2012
I am setting up 1811w router for accessing internet.DHCP is configured on it but it is not providing IP to laptop connected on port fa6. [code]
View 3 Replies
View Related
Oct 22, 2012
Need to confirm purpose of command below
dot11 ssid TEST
vlan 4
authentication open
authentication key-management wpa
guest-mode ?????
Why we need guest-mode command in above config?
View 5 Replies
View Related
Oct 19, 2012
I am setting up 1811w router for accessing internet. DHCP is configured on it but it is not providing IP to laptop connected on port fa6.
Here is config of router
dot11 ssid internet
vlan 98
authentication open
[Code].....
View 22 Replies
View Related
Oct 23, 2012
Wireless is working ok on 1811W.Need to know from command output below what values are considered good for power and signal strenghts
1811w#sh dot11 associations all-client
Address : 40fc.894e.c48c Name : NONE
IP Address : 192.168.98.2 Interface : Dot11Radio0
Device : unknown Software Version : NONE
[code].....
Also what is Association ID mean in above output?
View 5 Replies
View Related
Oct 19, 2012
Trying to configure 1811w for wi fi . Need to use authentication shared keys but current IOS seems does not support ir
Router(config)#int dot11Radio 0
Router(config-if)#ssid manvee1
Router(config-if-ssid)#a?
% Unrecognized command
Router(config-if-ssid)#
(C181X-ADVIPSERVICESK9-M), Version 12.4(24)T8.
Need to know which IOS will support wi fi and authentication command under dot11 radio 0?
View 4 Replies
View Related
Nov 8, 2012
Using Cisco 1811W with IOS 15.1(4)M5. FE0 and FE1 are connected to the internet via Billion ADSL2+ modems operating in bridged mode. Both lines are similar so I'll only discuss FE0 from this point on.Local subnet is 192.168.128.0/24 with router on 192.168.128.1 as default gateway. Modem on FE0 has static LAN IP of 192.168.128.2 and when plugged into the switch on the LAN side, the web interface can be accessed at that IP address. Unplug the modem from the switch and plug it into FE0 and it now works as desired providing access from the router to the internet but the web interface is no longer accessable at 192.168.128.2
I tried adding a static route "ip route 192.168.128.2 255.255.255.255 FastEthernet 0" and also "ip route 192.168.128.2 255.255.255.255 Dialer 1" Neither worked and presumably it isn't that straight forward. Possibly NAT or other routing configuration required.Although there isn't much to configure when in bridged mode, I mostly want this setup so I can look at the ADSL connection status and for the modem to write messages to syslog (works when plugged into switch on LAN side), or SNMP access.
View 3 Replies
View Related
Dec 14, 2012
I have 2691 Router conencted to Internet and it is doing Nat. This connects to 3550A Switch which has connection to 1811W Router.
I setup VPN between 1811W and 3550A. 3550A has connection to 2691 via ospf.
OSPF is running between 1811w and 3550A.
1811
1811w# sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
[Code].....
View 5 Replies
View Related
Nov 23, 2012
On 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies
View Related
Feb 3, 2011
I have a Cisco 3725 running IOS 12.3. I have three WAN connections (2 x 100Mb and 1 x 2Mb serial) and I need to replace the 2Mb serial connection with a further 100Mb connection. However, I have not got any spare 100Mb sockets.My plan is to use a switch that supports VLANs, connect the three WAN connections to the switch, each in their own VLAN, then connect the switch to one port on the router, configuring the switch port as a trunk (so that it passes all three VLANs across the link) and configuring the router so that for that single Ethernet interface, it has three subinterfaces each configured for a VLAN that matches the VLAN used for the corresponding WAN connection.
I am a bit rusty on my IOS so I wanted to run this all past the community for feedback. [code] Any thoughts on whether or not that will work? Are there any commands from the original interface configurations that I CANNOT use when moving them to a subinterface? I'm thinking that the speed & duplex commands need to be removed?
View 4 Replies
View Related
Dec 18, 2011
We're getting "Connaction Timeout / Connection Failure" error messages several time per day. Here is our setup:
Verizon FiOS Internet (ONT Box) --> Cisco ASA 5505 --> EdgeMarc 4500 Router --> Cisco 300-24G Switch --> Dell PE1950 Servers
From past few months, we keep getting Connection Timeout and Connection Failure error messages in our vendor application which connects to SQL Server 2005. Also Terminal Server 2003 keep disconnecting for every few hours.After several days of troubleshooting, we come to know that this Cisco ASA 5500 is not working properly. When I access the ASDM, it shows several warning messages.I know there is a setting option to configure TimeOut, but is there anyway to test and track the ASA 5500 regarding this Timeout issues?
View 3 Replies
View Related
Nov 26, 2012
I have a problem with my computer connections.When I plug in a network cable to access LAN, a wireless Internet connection gets disconnected.When I unplug the cable internet connection through wireless comes up.Some computers can support both connections cable for LAN and wireless for Internet.Other computers do not support both connections.
View 7 Replies
View Related
Jun 25, 2012
I am trying to confgure a VPN connection on a Cisco ASA 5505, and I am supposed to translate the inside network from 10.200 76.0 to host 10.1.4.204, and then from that scheme establish a VPN with the host 66.179.80.108 on network 192.168.50.0/24. I was told that this Cisco ASA appliace would be able to translate the network address as a mask in order to make the necessary connection with the other site connection.
View 6 Replies
View Related
Nov 15, 2012
I have an Acer 7750G, running Windows 7,connected to our home network using a Dynex router. At the moment this is the only laptop in the house that is having problems with connectivity. Starting yesterday, it only connects intermittently. When I run diagnostics, it says the following problems have been fixed but it either solves the problem for a few minutes only or not at all: "Problem with wireless adapter or access point" or "Default gateway is not available".
IPV6 connectivity also shows 'no internet access' and sometimes IPV4 reports no internet. I've unplugged and rebooted the modem and router a few times but that hasn't solved the problem.
Edit: I ran troubleshoot again, and it says the following issue is not fixed: "Wireless Network Connection 2 does not have a valid IP configuration".
View 14 Replies
View Related
Nov 29, 2012
so I would like to know if I have a cisco 800 series lets say with interface fa0/0 being my public interface.can I have on this interface an easyvpn connection to a hub and a crypto map xyz connection to another hub?all the tests I've done using gns3 indicate no. when I have both on the same interface only eazyvpn works. when I remove the eazyvpn from the interface then site to site works.I know with a crypto map I can have different tunnels but my question is a crypto map and an eazyvpn on the same outside interface can it work.if yes, do you have a configuration example of the 2 hubs and the spoke?
View 1 Replies
View Related
Mar 21, 2011
I just bought a "DLink Xtreme N Gigabit Router DIR-655" I configured it correctly. It works well for the wireless connection but my Lan connection (wired connection) does not work. The Lan computer connects to the router but cannot access the internet. All of my machines work OK with a Netgear G router, including the Lan computer.
View 9 Replies
View Related
Nov 5, 2011
I have problem with my Internet connection. Recently my Internet connection often get slow. There are 3 connections on the server running Windows Server 2003. 1st is External, 2nd is Internal and 3rd is VPN (please see attahement). There is nothing to do with External and Internal connections, and everytime the Internet connection get slow, I have to disconnection VPN (connection) and connect it again.
View 5 Replies
View Related
Jan 20, 2013
After connecting to the internet on my laptop, the internet connection will work great for 10 minutes or less than it slows down drastically or essentially not working at all. If I disconnect and reconnect it will work again but just for a short amount of time. The wireless connection works great on iPod, IPhone, and tablet. Downloaded Kaspersky Antivirus which said it fixed some viruses but internet got worse after that. Tried restoring the computer to factory settings and the internet stays connected for what seem a few minutes longer.
View 3 Replies
View Related
May 13, 2012
Every time I boot up my computer, everything will be working fine for about 5 -10 minutes, but after this, all my browsers will lose connection to the Internet. All of them: IE, firefox, chrome, even the steam browser, all of them just lose connection.The weird thing is, my net connection is perfectly fine: I can still play online games, still use online chat services, still open and use programs like utorrent. It's like something is just blocking all my browser connections.When I run a network troubleshooter, it says "your computer appears to be correctly configured, but the device or resource (Microsoft Corporation: Software, Smartphones, Online, Games, Cloud Computing, IT Business Technology, Downloads) is not responding."I googled this and came across some apparent fixes like flushing and re-registering my dns and restarting my modem, niether of which has worked.In addition, this problem is showing up on two totally separate shared networks and has only affected my computer. Other netwworked devices, like friends/families computers and my iPhone (which I am using to type this) work fine.
View 1 Replies
View Related
Jun 26, 2012
My hp laptop will no longer connect to the internet thru both a wifi connection or cable connection. I've also tried to do a system restore to an earlier date and it will not let mme do this either
View 4 Replies
View Related
Aug 9, 2011
i have cable internet. and im supposed to get up to 15Mbps. but i only get that on a good day. i average around 10Mbps.but im paying $60 a month for the 15Mbps. i can get at&t u-verse at 18Mbps for $39.95 a month for 12 months. then it goes up to $44. does any one her use U-Verse? and do you think its a better deal then cable?
View 3 Replies
View Related
Nov 20, 2010
I want to add WCS as a AAA client for authentication with Radius in my set-up.how to configure WCS for the same.where are all those options in WCS.
View 7 Replies
View Related
Apr 21, 2013
When I try connecting via anyconnect the logs (and anyconnect messages) state the connection "cannot be established due to no addresses being available for SVC connection'". The group etc has a dhcp scope assigned, (and this was working for the past year). I'm not sure what config changes (if any) he made before leaving.
View 10 Replies
View Related
Mar 23, 2011
I would like to configure my Cisco 881 enabling Dual Wan (load balancing and failover). First link: HTTP, FTP, SMTP,...Second link: DATA inter-site (VPN), VoIP,Does the configuration seem OK?What does the command line "track 1 rtr 1 reachability delay down 1 up 1" mean?To send the different flow on one or the other port, do i have to configure it on the ACL1 and ACL2 ?
View 9 Replies
View Related
