Cisco VPN :: 800 EasyVPN Connection To Hub And Crypto Map Xyz Connection To Another One
Nov 29, 2012
so I would like to know if I have a cisco 800 series lets say with interface fa0/0 being my public interface.can I have on this interface an easyvpn connection to a hub and a crypto map xyz connection to another hub?all the tests I've done using gns3 indicate no. when I have both on the same interface only eazyvpn works. when I remove the eazyvpn from the interface then site to site works.I know with a crypto map I can have different tunnels but my question is a crypto map and an eazyvpn on the same outside interface can it work.if yes, do you have a configuration example of the 2 hubs and the spoke?
View 1 Replies
ADVERTISEMENT
Oct 26, 2012
I would like to use a Cisco 1921 at my house and create a "Easy VPN Remote" connection to our ASA 5510 at work. Can I use the Easy VPN Client with the base license, or do I need the security license to take advantage of the VPN tunnel?
View 4 Replies
View Related
Feb 3, 2011
I have a Cisco 3725 running IOS 12.3. I have three WAN connections (2 x 100Mb and 1 x 2Mb serial) and I need to replace the 2Mb serial connection with a further 100Mb connection. However, I have not got any spare 100Mb sockets.My plan is to use a switch that supports VLANs, connect the three WAN connections to the switch, each in their own VLAN, then connect the switch to one port on the router, configuring the switch port as a trunk (so that it passes all three VLANs across the link) and configuring the router so that for that single Ethernet interface, it has three subinterfaces each configured for a VLAN that matches the VLAN used for the corresponding WAN connection.
I am a bit rusty on my IOS so I wanted to run this all past the community for feedback. [code] Any thoughts on whether or not that will work? Are there any commands from the original interface configurations that I CANNOT use when moving them to a subinterface? I'm thinking that the speed & duplex commands need to be removed?
View 4 Replies
View Related
Dec 18, 2011
We're getting "Connaction Timeout / Connection Failure" error messages several time per day. Here is our setup:
Verizon FiOS Internet (ONT Box) --> Cisco ASA 5505 --> EdgeMarc 4500 Router --> Cisco 300-24G Switch --> Dell PE1950 Servers
From past few months, we keep getting Connection Timeout and Connection Failure error messages in our vendor application which connects to SQL Server 2005. Also Terminal Server 2003 keep disconnecting for every few hours.After several days of troubleshooting, we come to know that this Cisco ASA 5500 is not working properly. When I access the ASDM, it shows several warning messages.I know there is a setting option to configure TimeOut, but is there anyway to test and track the ASA 5500 regarding this Timeout issues?
View 3 Replies
View Related
Nov 26, 2012
I have a problem with my computer connections.When I plug in a network cable to access LAN, a wireless Internet connection gets disconnected.When I unplug the cable internet connection through wireless comes up.Some computers can support both connections cable for LAN and wireless for Internet.Other computers do not support both connections.
View 7 Replies
View Related
Jun 25, 2012
I am trying to confgure a VPN connection on a Cisco ASA 5505, and I am supposed to translate the inside network from 10.200 76.0 to host 10.1.4.204, and then from that scheme establish a VPN with the host 66.179.80.108 on network 192.168.50.0/24. I was told that this Cisco ASA appliace would be able to translate the network address as a mask in order to make the necessary connection with the other site connection.
View 6 Replies
View Related
Nov 15, 2012
I have an Acer 7750G, running Windows 7,connected to our home network using a Dynex router. At the moment this is the only laptop in the house that is having problems with connectivity. Starting yesterday, it only connects intermittently. When I run diagnostics, it says the following problems have been fixed but it either solves the problem for a few minutes only or not at all: "Problem with wireless adapter or access point" or "Default gateway is not available".
IPV6 connectivity also shows 'no internet access' and sometimes IPV4 reports no internet. I've unplugged and rebooted the modem and router a few times but that hasn't solved the problem.
Edit: I ran troubleshoot again, and it says the following issue is not fixed: "Wireless Network Connection 2 does not have a valid IP configuration".
View 14 Replies
View Related
Mar 21, 2011
I just bought a "DLink Xtreme N Gigabit Router DIR-655" I configured it correctly. It works well for the wireless connection but my Lan connection (wired connection) does not work. The Lan computer connects to the router but cannot access the internet. All of my machines work OK with a Netgear G router, including the Lan computer.
View 9 Replies
View Related
Nov 5, 2011
I have problem with my Internet connection. Recently my Internet connection often get slow. There are 3 connections on the server running Windows Server 2003. 1st is External, 2nd is Internal and 3rd is VPN (please see attahement). There is nothing to do with External and Internal connections, and everytime the Internet connection get slow, I have to disconnection VPN (connection) and connect it again.
View 5 Replies
View Related
Jan 20, 2013
After connecting to the internet on my laptop, the internet connection will work great for 10 minutes or less than it slows down drastically or essentially not working at all. If I disconnect and reconnect it will work again but just for a short amount of time. The wireless connection works great on iPod, IPhone, and tablet. Downloaded Kaspersky Antivirus which said it fixed some viruses but internet got worse after that. Tried restoring the computer to factory settings and the internet stays connected for what seem a few minutes longer.
View 3 Replies
View Related
May 13, 2012
Every time I boot up my computer, everything will be working fine for about 5 -10 minutes, but after this, all my browsers will lose connection to the Internet. All of them: IE, firefox, chrome, even the steam browser, all of them just lose connection.The weird thing is, my net connection is perfectly fine: I can still play online games, still use online chat services, still open and use programs like utorrent. It's like something is just blocking all my browser connections.When I run a network troubleshooter, it says "your computer appears to be correctly configured, but the device or resource (Microsoft Corporation: Software, Smartphones, Online, Games, Cloud Computing, IT Business Technology, Downloads) is not responding."I googled this and came across some apparent fixes like flushing and re-registering my dns and restarting my modem, niether of which has worked.In addition, this problem is showing up on two totally separate shared networks and has only affected my computer. Other netwworked devices, like friends/families computers and my iPhone (which I am using to type this) work fine.
View 1 Replies
View Related
Jun 26, 2012
My hp laptop will no longer connect to the internet thru both a wifi connection or cable connection. I've also tried to do a system restore to an earlier date and it will not let mme do this either
View 4 Replies
View Related
Aug 9, 2011
i have cable internet. and im supposed to get up to 15Mbps. but i only get that on a good day. i average around 10Mbps.but im paying $60 a month for the 15Mbps. i can get at&t u-verse at 18Mbps for $39.95 a month for 12 months. then it goes up to $44. does any one her use U-Verse? and do you think its a better deal then cable?
View 3 Replies
View Related
Nov 30, 2012
URL What changes are needed to the 2821 config that is behind another Cisco router? And what static ports should be opened on the MAIN Cisco router that is in front of the 2821?
View 1 Replies
View Related
Aug 12, 2012
Can the Cisco ASA 5510 appliance be used as an EasyVPN Remote device, or only as an EasyVPN Server?
View 1 Replies
View Related
Feb 23, 2011
We have many new and very small remote sites that will be connecting via an ASA5505 using easy VPN. Works without an issue and we've got the configuration and process nailed down.
The challenge I was presented with today involve non-standard remote sites where I need to configure a third interface on an ASA 5505 and allow it to pass directly to the Internet and not go through the VPN. Configuration of the third interface, assignment and configuration of the ACLs / NAT(PAT) are straight forward.
The challenge I face and haven't been able to find a direct answer to is if it's possible to have the traffic bypass the easy vpn network extension process. At this time the traffic is going down the tunnel which isn't what I want.
I fear I'll have to build classic site-to-site VPN configurations which isn't a huge issue though it breaks all maintenance/operations methods, processes and I'll have to spend time training the support team how to detect the differences.
View 2 Replies
View Related
Jun 16, 2011
I don't seem to be able to connect to my cisco 831 router with easy vpn server configured using my Blackberry Playbook. Looking at the console of the router i can see the debugging but am not sure what it all means.
Current configuration : 2574 bytes!version 12.3no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!enable secret 5 $1$FM71$y4ejS2icnqX79b9gD92E81enable password xxxx!username CRWS_Ritesh privilege 15 password 0 $1$W1fA$o1oSEpa163775446username shamilton privilege 15 secret 5 $1$wFLF$8eRxnrrgVHMXXC0bXdEGi1aaa new-model!!aaa authentication login default localaaa authentication login ciscocp_vpn_xauth_ml_1 localaaa authorization exec default localaaa authorization network ciscocp_vpn_group_ml_1 localaaa session-id commonip subnet-zerono ip
[code]....
View 13 Replies
View Related
Oct 18, 2012
I've two sites, the branch with an ASA 5505 and on the corporate office i've an ASA 5510.I need to make a easy vpn tunnel between this to sites and I've made some configuration, but for now, the ikev1 isn't working.
View 1 Replies
View Related
Mar 15, 2011
I have one ASA 5510 on main office that access the internet trought of a private link and one ASA5505 on the branch office that access the internet trought of a ADSL link with dynamic IP.
Behind ASA 5510 the network is 10.8.40.0/24 and behind the ASA 5505 the network is 10.30.103.0/24. I want access both network trought of the frame-relay link and the internet link with EzVPN.I make that access only ip on the main office, this comunication go to frame-relay link and the everyone go to the VPN.When the traffic go to the frame-relay link, I use a NAT Static Policy that change the source 10.30.103.0/24 to source 10.40.103.0/24. Its work OK when a VPN do not UP.When the VPN is UP, the NAT dont work and the packet go to the true IP (10.30.103.0/24).
View 1 Replies
View Related
Feb 25, 2013
How to setup option 150 in IP pool on VPN Client.
View 2 Replies
View Related
Jul 11, 2012
I have been trying to configure Cisco1941/K9 as Easy VPN Server through CiscoCP.The tunnel comes up but I cannot pass any traffic to the secure LAN (GigEth 0/1). When the tunnel comes up, I can ping the Loopback interface and the GigEth 0/1 interface IPs.
View 21 Replies
View Related
Dec 5, 2011
I have a Cisco ASA 5510 and a Cisco ASA 5505. I want to configure the ASA 5510 as Easy VPN Server and 5505 as Easy VPN hardware client.Using either CLI or ASDM.
View 1 Replies
View Related
May 16, 2012
I'm in the process of setting up a working VPN/Firewall setup on an 881W ISR. I have the firewall, NAT, and VPN working, and I'm able to connect remotely to my router. The problem I am having is that I none of my VPN cllients can connect to the internet. I suspect that my firewall rules may have something to do with this. Let me break-down what I have, and what I want to achieve:
1. My router is setup with VLAN1 (172.16.1.0/24) as the inside zone (in-zone), while my outside zone (out-zone) is FastEthernet4 (DHCP WAN Interface). I also have a guest zone (guest-zone) VLAN12 (192.168.12.0/24) used for my guest SSID wireless, which is NATed to the outside zone.
2. I have my EasyVPN setup using a Virtual Template Interface that terminates at the WAN interface FastEthernet4 (something tells me this should be changed). Should I terminate at VLAN1, or an interface or loopback on VLAN1?
3. I ultimately want the VPN users to be able to conenct to the local resources on VLAN1 only, while being able to get out to the internet. [code]
View 14 Replies
View Related
Jul 11, 2011
I have a Cisco ASA 5505 which is setup as an EasyVPN client to e remote VPN concentrator.
The Cisco ASA has the 50 internal user license with 10 VPN peers.
We just upgraded the license from the base 10 internal user to 50 user license but it has not resolved the problem and only 10 internal users still work, the 11th fails.
Does each EasyVPN client on the inside network take up 1 of the 10 VPN peer licences?
This seems to be the issue from what I can see, just need confirmation.
View 1 Replies
View Related
May 3, 2011
I have big trouble with easyvpn clients access filtering on asaos 8.4.1. I have couple of remote offices with hardware clients (cisco 87x, 88x) configured as easyvpn clients to Asa. Default route in it's routing table pointing to the Virtaul-Access interface (easyvpn connection to ASA), so there is no split tunneling or any kind of nat on the clients. I have ip-telephony deployed across remote offices. This remote offices should be able to call to each other.
On the ASA i have configuration for this purpose:
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
But as soon as I configured it, remote users obtain an ability to access Internet without any restrictions although there is couple of access-lists configured on the outside interface pointing to easyvpn clients. Then there is no same-security-traffic commands i can filter out access to internal and external resources correctly, but remote offices can't communicate with each other
View 1 Replies
View Related
Mar 7, 2011
I have this situation, I need to establish an IP sec communication to another site but I need to identify all my packets sent, as a different networks as my local one. for example: my local network is 10.5.0.0/24 and I need to sent packets as 10.6.0.0/24. I suppose that I need to do Nat with this IPs. But in this router Nat is already applied to outbound traffic to Internet. How can I apply this NAT to crypto map only?
My router is a Cisco 877 with 12.4 IOS an this is the relevant configuration, crypto map vpn it´s used to sent traffic to second site.
crypto isakmp policy 2 encr 3des authentication pre-share group 2crypto isakmp key xxxxxxxxx address XX.XX.XX.XX
crypto ipsec transform-set vpn esp-3des esp-sha-hmac
crypto map vpn 1 ipsec-isakmp set peer XX.XX.XX.XX
[ code]....
View 2 Replies
View Related
Mar 8, 2012
I have a Cisco ASA 5505 which is setup as an EasyVPN client to e remote VPN concentrator.The Cisco ASA has the 50 internal user license with 10 VPN peers.We just upgraded the license from the base 10 internal user to 50 user license but it has not resolved the problem and only 10 internal users still work, the 11th fails. Does each EasyVPN client on the inside network take up 1 of the 10 VPN peer licences? This seems to be the issue from what I can see, just need confirmation.
View 3 Replies
View Related
Aug 28, 2011
(Router is ISR 1921)This is doing my head in. I am not using NAT, there are no ACLs, there is no split horizon.Here is what I have. It is practically generated by CCP. When connected I cannot ping the loopback interface or the gig0/0 interface, (not to mention anything else).
version 15.0
service config
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname dcsgw1
[code]...
View 13 Replies
View Related
Jan 23, 2013
I have a branch office set up with a cable modem and an ASA 5505 as an easyvpn hardware client with network extension mode enabled, and connects to a PIX515E at the headend.I'm working on a separate issue for why the Internet connection drops periodically at the site, but my main problem is as follows.In this location, I have an 1142 LAP. It can boot up, and join the WLC just fine. Performance seems a little slow when it's working, but it works. The real issue is, if the VPN connection drops and reestablishes for any reason, the wireless clients all cease being able to communicate. All wired clients seem to bounce back without a problem.
The access point still shows to be joined to the controller, the access point never goes down, just wireless clients can't access anything any more. If I reload the access point, clients reassociate and continue on their merry way. For now, I am experimenting to keep the connection from dropping, but I'd really like to get it where I don't have to babysit this thing all day and night, and it can rejoin and function normally by itself after an outage.We are changing to this configuration from wireless bridging due to interference and reliability issues - however, I never experienced any similar issues with this particular access point before, so it's not the access point itself.
View 4 Replies
View Related
Oct 10, 2012
I am installing 2 ASA 5505s at home offices with dynamic IPs. The EasyVPN server is a ASA585x. I am using the 5505s in NEM mode. I configured a unique DHCP scope on each 5505. I have a dynamic crpto map on the server. I configured unique tunnel groups, group policies and usernames for each site on the server. This seems to work fine. Is it normal to configure unique tunnel groups, group policies and usernames for each remote site?
View 2 Replies
View Related
Mar 2, 2011
When ASA 5505 was installed we selected Easy VPN Remote. Now we want to disable it. In ASDM we navigate to Configuration > Remote Access VPN > Easy VPN Remote and try to clear the Enable Easy VPN Remote checkbox but it will not uncheck.
View 2 Replies
View Related
Oct 26, 2010
I am using Cisco configuration professional to set up one easy vpn server on 887-K9,vpn client can dial up the server successfully but can only ping router but on other lan. Looks like there is a nat issues between lan and vpn client?
View 5 Replies
View Related
Apr 28, 2011
So I have three ASA 5505 firewall. my firewalls we are in the test environment. I read on the net that when you have a situation like in my company where are headquarter and two offices, i should put in each branch office and headquarter one asa firewall and a firewalls should be configured as easyvpn.
VPN server is in headquarter and easyvpn's are in branch offices. i tried everything, but we could not configure them. maybe it's not a problem that in my test environment at my the external interfaces which have static addresses on these three firewalls, respectively serever 192.168.2.1, 192.168.2.2 and 192.168.2.3 client client. I seted firewalls by following the instructions, but does not work
[URL]...
I solved the problem with the server as a remote access VPN. client workstations that are on the 192.168.2.0/24 network can access a local LAN via VPN. But when you put the ASA 5505 firewall. clients on the LAN side of the firewall can not access the VPN. I use software products Cisco VPN Client 5.0.06, but when I create a connection and try to connect to get an error secure vpn connection terminated locally by the client. reason 412: the remote peer is no longer responding.
View 2 Replies
View Related
