Cisco VPN :: 5505 Make Necessary Connection With Other Site Connection
Jun 25, 2012
I am trying to confgure a VPN connection on a Cisco ASA 5505, and I am supposed to translate the inside network from 10.200 76.0 to host 10.1.4.204, and then from that scheme establish a VPN with the host 66.179.80.108 on network 192.168.50.0/24. I was told that this Cisco ASA appliace would be able to translate the network address as a mask in order to make the necessary connection with the other site connection.
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
We've just deployed a site-to-site VPN using a 5505 ASA on the client's site and a checkpoint Nokia FW on our site. Everything seems to be fine except that the user's connections to their file shares seem to be intermittently dropping. One minute the connection to the shares is there, next thing it's lost. There is no logic to it because no two users are experiencing issues at the same time, as a matter of fact even on the same PC where a user has access to 3 shares on 3 different servers, one could be showing as connected whereas the other two be dropping. [code]
As you can see the Duplex and Speed are set to auto, I've rectified this since then and I'm keeping a close eye on the output errors, and collisions. However, I'm afraid that this did not rectify the issue and the users are still experiencing intermittent connection dropping to their file shares over the VPN!
im drawing a blank trying to setup a site to site connection with a 5505 ASA using ipsec and isakmp.i have the pre shared key as well as the external address of the other end of the tunnel but do not remember what the commands are to setup the crypto map and isakmp.
i configured site to site VPN beetwen the asa 5505 (asa 8.4.2) and the asa 5510 (asa 8.4.4). how i can configure that the users from one side and second side use internet in same time?
We have a site to site client that is having issue with intermittent disconnects. The Main endpoint is a CIsco ASA 5520 8.4.3 and the remote site has a a Cisco ASA 5505 8.2.5.
If we have a disconnect, we can "logout" of the Main ASA and the connection seems to find itself and traffic will flow. This take place about every 1 - 5 minutes but if you reset the crypto (which I am assuming you do) by logging out under the Logging Monitor Session - ikev1 sessions. It all starts right back up.
I am stumped. At first I thought MTUs but I am not sure that is the answer.
Recently I used the wizard to create an IPsec site-to-site connection, which went very smoothly; however, I now noticed that when I connect via Anyconnect 2.5.0217 I cannot get to local and subnatted resources on the network.
I rolled back to saved config file, which was taken before the site-to-site vpn was created, but that did not work as well.What should I check to see why I can no longer get to different subnets after the site-to-site vpn connection.
our customer unfortunately uses a Watchguard.Finally we could establish a site-to-site vpn connection.To test if the connection re-establish again, we cleared our vpn session by "clear crypto isakmp <session id>" and after that "clear crypto sa <ip address of the peer>"After that, the session is down on our site, but the watchguard keeps the Phase I still up, either the deleting messages from our cisco are visible in the watchguard log files.Watchguard helpdesk told us, that the messages are only seen as a deletion message for Phase II, therefore Watchguard keeps Phase I up and running.Here you could see the cisco 7206 log messages aftre the clear commands:
In my opinion, it looks ok and we do not have problems with other VPN devices with this kind of tests.what could be done that the watchguard deletes Phase I, too? Or that an explicit Phase I deletion message is created and sent by our cisco 7206?
currently I have a Cisco 2921 router and I have one active site-to-site VPN connection through the internet.my question is; how I can create another Ipsec site-to-site VPN connection ? I have to keep the 1st VPN connection active.
We have 3 sites, with a Cisco ASA 5520 at each location.
HQ (Headquarters) internal network: 172.16.110.0/24, DR (Disaster Recovery) internal network: 172.16.120.0/24 BO (Branch Office) internal network: 172.16.150.0/24
HQ and DR have a 100Mbps permanent MPLS link between each other.Branch Office has a Site 2 Site VPN connection to HQ. If it fails, it establishes a Site 2 Site VPN connection to DR. This works perfectly.Now the routing issue... There is no route to the BO in the routing table at HQ/DR. The default gateway is used to reach the BO and that works for HQ when the VPN is between HQ/BO. If the VPN fails over to DR/BO, HQ can't reach BO anymore.I need to have some kind of conditional route injection from the ASA where the VPN is established. I was considering a tracked static route, but I was wondering if the S2S VPN itself has a functionality to do so. I thought the Reverse Route Injection was it but it's enabled on our crypto map and doesn't seem to work...
From past few months, we keep getting Connection Timeout and Connection Failure error messages in our vendor application which connects to SQL Server 2005. Also Terminal Server 2003 keep disconnecting for every few hours.After several days of troubleshooting, we come to know that this Cisco ASA 5500 is not working properly. When I access the ASDM, it shows several warning messages.I know there is a setting option to configure TimeOut, but is there anyway to test and track the ASA 5500 regarding this Timeout issues?
I would like to know if there is any command that i can use to terminate a site-to-site connection and restart it whenever i want to.I don't want to use the shut down command since i use the specific interface as an exit point to the internet.
I am planning on setting up a site to site VPN with two ASA5505s across a WAN connection. Take a look at my setup and answer this. To get this started, I would need to get my ISP to route any traffic from my external IP address to which address: 192.168.100.220 or 10.255.255.2. I have never done this before. Inside port is 192.168.100.220, Outside port is 10.255.255.2
I currently configured a site-to-site vpn connection in one of our client. Configuration is fine and site-to-site connection is working properly.We noticed that when the tunnel is idle the site-to-site connection between these two branches is disconnected.
We need to ping the other site in order to re-establish the connection and perform a continuous ping in order to keep the tunnel active. Any way to keep the tunnel active even though there are no activity running on both sites and even without pinging continuously.
I have dsl connection from TE-data from 3com modem in 2 sites. and I have 2 cisco routers 1921 and there is a vpn site to site between them and the VPN connection is working good. and i configured PAT on one of them to allow the users access the internet but tere is a problem: [code]
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
Should i get a wireless adapter Or a wireless repeater Which would be better for a better connection?My router is down stairs and my xbox is upstairs.I could get the wireless adapter upstairs then do an ethernet cable straight to my xbox.
I'm using XP SP3. I'm trying to connect using the Local Area Connection for the first time. Up to now I've been using wireless but I'd like to get better performance.
Here are my current settings via IPconfig: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . :
[Code].....
I've tried releasing and renewing via IPconfig. Renewing gives me the following error message: An error occurred while renewing interface Local Area Connection : unable to contact your DHCP server. Request has timed out.
I've got limited connectivity. It's trying to send but cannot receive.
My laptop used to connect wireless very well. About 10 days, it lost the connection even though the wireless signals were excellent. I guess it might be due to a virus attack that disabled my wireless connection. I run System Restore on Networking but not successful.
Internet works in that I can get onto a site but not login ie banking - also can't get results once I get onto National Lottery site, login into Hotmail. The diagnostics log states it could not make an HTTPS connection but nearly every thread I have read mentions firewall problems. I don't have Norton, just Windows Firewall and Lavasoft Adaware, but turning both off doesn't change anything. My PC is a Dell, I use a Cisco modem and a Belkin wireless router for my kids to run their XBoxes, all have been fine for 2 years. [code]
I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
i just managed to config the Cisco 877 and send it to my client,when the client connect the router from his location the router can't make VPN connection to my HQ office,i can connect to the router using the external IP adress,i tried to reset the VPN tunnel but no avail,
i have a 5510 with SDM 8.2.5 from clients connected to LAN i cant open a VPN connection! (using windows client L2TP or PPTP) there is not rules tho block this ports, why i cant connect?
i have router 3845 and then it's connected with pix and then its connected with vpn tunnel to the customer router. i am here trying to make vpn connectivity for devices. so on router i did static nat statements 10.124.90.124 10.200.200.1. this type of six statements i wrote for six devices. on the pix i did
i have one question that i need to use physical subnet or nat subnet for crypto map acl? and also on the customer router which subnet they can use as well nat sunet or my router physical subnet?
I can't access the internet through my home pc. I can't setup a new connection because I'm missing the network icon. It was fine a few days ago but somehow somewhere I've lost the icon. I have tried to restore but couldn't bo back that far.
I am trying to make 2 COMPLETELY seperate networks with only 1 internet connection. We have routers, switches and all that. But we need to know how to set it all up. there are 2 companies in the same office, each company needs their own network at which they can view eachothers files but in no way view the other networks files.
I have an internet connection coming into my house. The modem is in the basement along with the desktop computer and the wireless router is wired upstairs where coverage is the greatest. Could some tell me how I would make these connections/ hardware needed to have them all on the same network?
