I am trying to make 2 COMPLETELY seperate networks with only 1 internet connection. We have routers, switches and all that. But we need to know how to set it all up. there are 2 companies in the same office, each company needs their own network at which they can view eachothers files but in no way view the other networks files.
View 1 RepliesI am trying to set up two routers so that I can offer free wireless connectivity via three AP's in three adjoining rooms on a first floor and secured wireless and wired network connectivity in upstairs offices. The setup is like this:
Verizon DSL connectivity..static IP
The gateway modem/router is a Verizon DLink DSL 2750B with three ports connecting to three wired Access Points in three first floor adjoining rooms, and the 4th port connecting to a Cisco E1200 (wireless and ethernet router) located next to the Verizon Dlink. I would like the Verizon DLink to give open wireless connectivity via the access points and also connect to the adjacent E1200 router.
I would like the Cisco E1200 to offer secured wireless and ethernet connectivity to the upstairs offices. (connecterd to the Cisco E1200 is a 24 port Netgear switch.)I have spent considerable time talking with Verizon and Cisco/Linksys but have not been successful in just how to set this up.A former tech actually did have this setup but for what ever reason the settings were reset to factory defaults with no written record as to the necessary settings.
i need to use two LAN connections one of INTERNET and one of internal server
View 1 Replies View RelatedI have 2 PCs at home. Lets name one of them as PC 1 which has two onboard LAN Ports. Now, PC1 has to connect to PC 2, just a home network for easy transfer on files and stuff, and it also has to connect to the internet via a network. The problem is both of them use static ip and when I tried configuring PC 1, it allows only one of the connections to remain active. I simply get an error otherwise saying "Multiple Gateways" will cause conflict and I will be stuck with only one connection. After much study I "somehow" connected both. I vaguely remember using the "route" command in cmd to achieve this. But now, I am getting an error when I try to access PC 2. My Internet is working fine.I am not network savvy at all. run both these connections from PC 1. I should add that I can in no way modify/change/or do anything else to my internet network since it is out of my control. I can do anything, however, for my Home Lan with PC 2. I run windows 7. Both the connections are wired, by the way.
View 2 Replies View RelatedCan I have 2 routers and make 2 separate wireless signals? Reason being I need one so that I can keep net blacks for my little brother but I would like my net not to have any restrictions.
View 1 Replies View RelatedI would like to set up two separate networks from one internet connection(modem), with the goal being to have a public network(Network A) that would have a small server on it, and then having a second secured network(Network B) that would have my personal computers on it. And both networks having connection to the internet. (The idea being that if the server somehow became compromised that my personal computers and their data would be safe)I have done some research and found that many people claim this can be done with just two or three routers, but none of them go into any detail about how to configure the routers. Below are the physical setups of the two options that I have come up with in my research, which if either would you recommend? And how would I configure each of the routers?
--------------
Modem/router 1 (Network A public)
--Internet-in WAN port
--port 1 to WAN of router 2-------------l
--port 2 server
[code]...
I have two subnets at my home and both run through my Cisco router. One is my private LAN with access to the Internet, ie your standard home network. The other is a semi-public network that I share with friends through an encrypted GRE tunnel system(DMVPN) over the Internet. I have a server on that semi-public network and I can access my friend's servers from my server, but not from my main PC on my private network.
Is there a way I can access both networks from only my main pc using two nic's?
how I can setup two separate networks on a Westell 327w modem/router. I know this question has been asked to death and I've utilized the search function, but I still don't know how to make this work. I have a computer that I plan on using for important business and my sibiling has my other computer that he uses for gaming and downloading stuff. His computer is connected wirelessly to the Westell 327w. My computer has no internet access at this point. I would like to have both connected wirelessly to the internet, but keep them completely separate and as secure as possible, as he downloads some questionable things.
View 1 Replies View RelatedI have two separate network with their own internet access as shown below I want to keep all setting of the left network unchanged. I can change the IPs and setting of the right side network.I want to be able to access all devices of the two network from my computer but in the same time the two network work as usual with no problems ( the same when they are sperate).One option is to set the LAN of modem 2 to 192.168.2.2 and connect one of the LAN port to LAN port of the Mkrotik router. Set the WAN of my private home router as
IP: 192.168.2.100
subnet mask: 255.255.255.0
gateway: 192.168.2.2
Home router LAN: 192.168.3.1
Is their another method to connect the two network and keep the same setting for the network on the left side?
I'm new at this stuff and very stumped. I have one WAP with multiple SSIDs that support VLAN ID (for a private and guest wireless network) and a managed switch that supports tag or port based VLAN ID. How do I set up the switch so that the networks are separate, but can still reach their own routers to get on the Internet? In case details are necessary, the WAP is a Cisco Aironet 1130AG and the switch is a Netgear FS750T2
View 14 Replies View RelatedWe are a small office currently running a regular network (9 wired, 2 wireless) and also using the "guest" feature (7 wireless) on a Linksys E2000. We have a switch to connect our wired equipment to the E2000. If "A" is our regular network, and "B" is our guest network, is it possible to have 2 routers on 1 cable modem and still prevent network "A" from seeing Network "B" and vice versa?? We are looking to do this because we will soon be exceeding the maximum guest users (10) allowed by the E2000. We have another Linksys router in storage, I think it is a WRT54G, that we would use if this is possible.
View 1 Replies View RelatedI want to connect 2 routers like this picture.No need to have it as separate networks.
View 3 Replies View RelatedWith traditional classful subnetting, the same number of host bits is used to designate the subnet ID for all the resulting subnetworks. This type of subnetting always results in a fixed number of subnets and a fixed number of hosts per subnet. For this reason, this is known as fixed-length subnetting. The decision about how many host bits to use for the subnet ID is a big planning decision. There are two considerations when planning subnets: the number of hosts on each network, and the number of individual local networks needed. The table for the subnet possibilities for the 192.168.1.0 network shows how the selection of a number of bits for the subnet ID affects both the number of possible subnets and the number of hosts that can be in each subnet. One thing to keep in mind is that in all IPv4 networks, two host addresses are reserved: the all-0s and the all-1s. An address with all 0s in the host portion of the address is an invalid host address and usually refers to the entire network or subnetwork. An address with all 1s in the host portion is used as the local network broadcast address. When a network is subnetted, each subnet contains an all-0s and an all-1s host address that cannot be used for individual host addresses.
View 2 Replies View RelatedI want to share one broadband connection between network A 192.168.1.xxx and network B 192.168.0.xxx. Network A is SBS 2008 while B is Linux with static IPs.
View 5 Replies View Related1. I currently have a Comcast Business Class Gateway, Cisco 2100 Series WLAN Controller and a Cisco ASA 5505 all connected together to supply LAN and WLAN internet connections on my network.
2. I also have a Card Access Security System on it owns network. It currently does not have internet access.
I would like to put my security system on the internet so that I can support it remotely. To do this, it has to be on a firewalled internet connection.Can I put the two networks on my ASA 5505 and keep them seperate? I don't want to provide a path into the Security System through my current LAN & WLAN. But I do need a frewalled internet connection on my Security System. I am trying to avoid purchasing a seperate firewall.
I have two dir655 routers that are connected. The second router is not setup as a wireless access point, but I am open to that if it will work. The second one is going to serve as a public wifi in a business, with a separate SSID. The first one is going to handle the local business network, with its NAS and printers. How would I prevent the public wifi from accessing the first router?
I have tried the guest wifi partition setting, however it still allows access to the lan devices on the first router. It does partition with the second router properly though, but thats not worth anything to me cause there are no lan devices on the 2nd router.
Would it work right if I turn the 2nd router into a access point, disable the dhcp server, and set it up with the guest wifi partition?
I have a network set up between two buildings. Each building has its own internet connection and DHCP server, building A using an RV180W router and building B using a linksys product. A WDS bridge has been set up between the two buildings using two wireless access points.The goal here is to allow clients in either building to be assigned an IP from their respective DHCP server (and thereby use that building's internet connection), yet still access network resources (eg file storage, printer, etc.) in the other building should the need arise.I have tried to set this up by having the RV180 assign IP's in the range 192.168.0.xxx to its clients in building A, and the linksys to assign IP's in the range 192.168.1.xxx in building B. I have enabled Vlan 1 and Vlan 2 on the RV180 - vlan 1 runs a DHCP server for building A. Vlan 2 runs no DHCP server and is directly connected to the WDS bridge to building B. Inter Vlan routing is enabled on both Vlan 1 and Vlan 2.On the WDS bridge modules, ive assigned both static IP's in the 192.168.1.xxx range (vlan 2 range). I've specified their dns and default gateway as 192.168.1.2 which is the static address for the RV180 in vlan 2.From a PC in vlan 1, I can ping and access the webgui for the WDS bridge modules which are in Vlan 2. However, i cannot ping any other computer in Vlan 2 which is set to accept a dynamic IP from the DHCP server operating in Building B. I assume this is because the WDS modules point to the RV180 as their default gateway and dns server, while the clients that have accepted a dynamic IP from the building B DHCP point to that device as their default gateway and DNS.I am considering trying changing the DNS and default gateway on the building B side of the WDS bridge to the building B values to see if that works, but am concerned i would lose all connectivity to the webgui from building A if i do that.
View 7 Replies View RelatedI'm an architect working in a small office that happens to be home to two seperate businesses, each with their owner network. However, these two networks want to use the same large format printer. I recently purchased the RV180W since the Cisco representative told me i would be able to connect both networks to the router so they can both see the printer without seeing the files on each of the other networks. We simply want to share the same printer.
Network 1:
192.168.4.1
Network 2
192.168.2.1
Large Format Printer
192.168.4.151
Network 1 has the RV180W as it's router with three gigabit switches. Computers and peripherals are connected to the three switches. 1 port open on the last switch.
I want to configure the RV180W to see both 192.168.4.1 and 192.168.2.1
What settings need to be modifed in order to accomplish this? Do I need more equipment? Is it easier to put a wireless card in one of the computers on the 192.168.2.1 network and then set it to see the 192.168.4.1 network?
We have 2 separate networks here, 1 for data (192.168.0.x) and 1 for VOIP phones (192.168.3.x).
I need them to both be connected to different ports on a switch (Cisco SG 300 10 port managed switch) which is then linked to another switch (Cisco Catalyst 2960 48 port switch). Then on this 2960 switch I want the link to be split back into the 2 separate networks. I think that I need to create 2 separate VLANs and assign them to different ports.
We have a two separate businesses in the same building who will both need access to shared resources and the same internet connection. They will need to remain on separate subnets and cannot communicate directly to each other. The current switch is a Cisco ESW-520-48P and we are looking at purchasing an SG-300-20P for the new business moving in. Heres how we envisage setting it up:
ESW-520 will host Company A's network. Workstations, servers etcSG-300 will have two VLANS. VLAN1 will host all Company B's network. Workstations, servers etc. VLAN2 will host the shared resources such as printers. The internet gateway is a UNIX based system with 3 NICS. 2 NICS are taken up by ADSL connections while the other NIC is the LAN, which would connect to VLAN2 on the SG-300. We would like to define which ADSL connection to route through depending on which subnet traffic is originating. The ESW-520 will need access to the shared resources and internet gateway on VLAN2 on the SG-300.
Using a Linksys E2000 and Linksys WRT54GL (both flashed to most recent firmware), I am trying to set up Network "A" and Network "B" on one modem. I do not want either A or B to be able to see each other for security purposes. Both are secured networks for the wireless connections and have different SSIDs.
After online research, and the inability to find my exact question answered, this is what I did and I'd like to know if I'm missing anything to keep A and B completely separate. Or, if I've done anything that will cause any problems on my network. [code]
I disabled the ability to change settings using wireless connection on both routers.
Having just installed the E1000 why have I got a public network address '####' which is security type WPA2 -PSK and also public network address '#### - Guest' which is security type - unsecured.Anyone can log onto either wireless network connection but only with the correct password.How do I remove the '####' address and also how do I make the '#### - Guest' address a secure one.
View 1 Replies View RelatedIs there any way to make networks hidden through the WiFi Smart software? I have a Cisco Linksys E4200V2. I have gone through everything to try figure out how to make my S.S.I.D. to not be broadcasted, but seems like the only way to make it hidden is to use the Origonal Firmware make it as hidden, then install the New Firmware and software. Seems like Cisco may have missed this option. I do know a lot of people would prefer their Networks hidden for a little security. I know it isn't much, cause if someone wants to get that info it's not hard to get it. But for people who don't know or don't want to waste all the time to find the Hidden Network name can be turned away, for going through that extra step.
View 6 Replies View RelatedI have Verizon fios with a modem that has a build in router. I purchased a secondary router so to separate what devices goes online. Now I did the easy setup wizard and connect the secondary router successfully however there is no Internet connection. Is how can I separate the routers and use the same internet connection.
View 11 Replies View RelatedMy first Rooter provides Broadband via a cable connection.Is it possible too add a second rooter too the first one and set the second one for WI-FI or is their a better way too get my Kindle WI-FI connected.
View 2 Replies View RelatedBasically I am trying to do a bit of a clean up at work and replacing two dlink (home style) ADSL modems with a single Cisco 2901 router with 2 ADSL HWICs. On top of this I want to isolate the 2 connections from each other, that is I don't want to use them as fail-over or anything just as 2 seperate connections. To do this I am using VRF tunnels.So far I have been successful in the global config of the switch and everything works. And when I put the lan, atm and dialer interface into my VRF it connects up all fine.My issue that I am having is that DNS (which is being pulled from the ISP via ppp ipcp dns) seems to just populate the global dns view, not the view I created for the VRF. This results in DNS queries not being able to be resolved but all other traffic is fine (i.e. I can ping and access anything on the net, I just can't resolve names).
If I have 2 ADSL connections, on two VRF tunnels, how can I seperate their DNS information for each connection/VRF tunnel? especially if that information is different as they overwrite the global DNS config each time they connect.... I could (and have successfully tested) statically assigning DNS servers to each DNS view but I would rather rely on each ISP sending their DNS servers as opposed to me hard coding them.
I am trying to confgure a VPN connection on a Cisco ASA 5505, and I am supposed to translate the inside network from 10.200 76.0 to host 10.1.4.204, and then from that scheme establish a VPN with the host 66.179.80.108 on network 192.168.50.0/24. I was told that this Cisco ASA appliace would be able to translate the network address as a mask in order to make the necessary connection with the other site connection.
View 6 Replies View RelatedMy fiance recently signed up for the Screen-wise Panel for Google research. Basically they monitor your TV usage and your internet usage. As part of the program they installed a Cisco WIFI router. I've got no issue with them logging the sites visited etc but I'm a little worried about them possible collecting private information (banking / work related stuff) that I don't want going out there. According to what I've read what's supposed to happen is they replace your router with the new Cisco router.The "technician" who came in and installed the router was actually a builder and not an IT technician and rather than replace our router he connected the Cisco router into port 4 of our router... I wasn't in at the time.
What I was looking to do is separate Port 4 of my router into a separate VLAN that can access the internet, but not access anything on ports 1-3, or the wireless. However, I want to be able to see everything on port 4 from the other side (in other words I want to see "into" the port 4 VLAN, but don't want them to see out). I also wanted DHCP to assign IP addresses correctly depending on where you were plugged in. In this example the first VLAN (your current router ip address) is going to be on 192.168.1.1, and the second VLAN (the new on we create on port 4) is going to be on 192.168.2.1.This is exactly what I'm looking to do, I could then connect the kids machines / tablets / ipods to the Cisco router and have the main machine and my work laptop on the main router... but I don't have a clue how to do it. </quote> Is this something that I am able to do with the Netgear router I own and is it hard to set up?
I set up my new EA4500 last night, and configured the 5Ghz and 2.4Ghz bands with separate SSIDs (as recommended). While I can see the 2.4Ghz band with all of my devices, I cannot see the 5Ghz band with any of them.I followed the advice given (including the settings shown) on the EA4500 FAQ.Title: Personalizing and connecting to the 5 GHz wireless band on a Linksys Wireless-N routerArticle ID: 21466.Did that *multiple* times, and still nothing. I do have a dual-band capable adapter (Netgear RangeMax WNDA3100 Dual Band Wireless-N Adapter) that I know works on 5Ghz (because I had it working on my old dual-band WDNR3700v1). Similarly, I have PCs sitting less than 20 feet away that were previously able to see the 5Ghz band on my old router, but are now unable to see it on the EA4500.
View 9 Replies View RelatedShould i get a wireless adapter Or a wireless repeater Which would be better for a better connection?My router is down stairs and my xbox is upstairs.I could get the wireless adapter upstairs then do an ethernet cable straight to my xbox.
View 7 Replies View RelatedI'm using XP SP3. I'm trying to connect using the Local Area Connection for the first time. Up to now I've been using wireless but I'd like to get better performance.
Here are my current settings via IPconfig:
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
[Code].....
I've tried releasing and renewing via IPconfig. Renewing gives me the following error message: An error occurred while renewing interface Local Area Connection : unable to contact your DHCP server. Request has timed out.
I've got limited connectivity. It's trying to send but cannot receive.
My laptop used to connect wireless very well. About 10 days, it lost the connection even though the wireless signals were excellent. I guess it might be due to a virus attack that disabled my wireless connection. I run System Restore on Networking but not successful.
View 6 Replies View RelatedI want to know that how to make a usb internet through dsl connection.
View 3 Replies View Related