Cisco Wireless :: Setting Up 1811w Router For Accessing Internet
Oct 19, 2012I am setting up 1811w router for accessing internet.DHCP is configured on it but it is not providing IP to laptop connected on port fa6. [code]
View 3 Replies
ADVERTISEMENT
Cisco WAN :: Accessing Settings Of 1811w Router?
Dec 4, 2011I have an 1811w router and can not figure out how to access the settings of the router. I do not have a console port that I can use to access the settings that way so I want to know how to do it using the SDM. I thought I was following the directions but for some reason when I connect my computer to one of the routers LAN ports no connection is recognized on either the router or the computer. How do I go about connecting to the router and accessing the settings?
View 1 Replies View RelatedCisco WAN :: 1811W Accessing Web Interface On ADSL Modem In Bridged Mode
Nov 8, 2012Using Cisco 1811W with IOS 15.1(4)M5. FE0 and FE1 are connected to the internet via Billion ADSL2+ modems operating in bridged mode. Both lines are similar so I'll only discuss FE0 from this point on.Local subnet is 192.168.128.0/24 with router on 192.168.128.1 as default gateway. Modem on FE0 has static LAN IP of 192.168.128.2 and when plugged into the switch on the LAN side, the web interface can be accessed at that IP address. Unplug the modem from the switch and plug it into FE0 and it now works as desired providing access from the router to the internet but the web interface is no longer accessable at 192.168.128.2
I tried adding a static route "ip route 192.168.128.2 255.255.255.255 FastEthernet 0" and also "ip route 192.168.128.2 255.255.255.255 Dialer 1" Neither worked and presumably it isn't that straight forward. Possibly NAT or other routing configuration required.Although there isn't much to configure when in bridged mode, I mostly want this setup so I can look at the ADSL connection status and for the modem to write messages to syslog (works when plugged into switch on LAN side), or SNMP access.
Cisco Wireless :: 1811W Router - Convert To Lightweight?
Nov 11, 2012We have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I am running
WCS 7.0.230.0
WLC 5508 (same code)
Cisco Wireless :: Base Configuration For 1811w Router?
Mar 2, 2009Need basic wireless configuration for a SOHO Cisco 1811W router? I just need the wireless to connect to the base wired LAN - with both WEP and MAC authentication. And - can the MAC auth. parameters be configured via CLI and not have to use either SDM or CP? I can access the router via SDM - but the Wirless Application will not fire up - and CP doesn't work at all.
View 18 Replies View RelatedCisco Wireless :: Guest-mode Command In 1811W Router
Oct 22, 2012Need to confirm purpose of command below
dot11 ssid TEST
vlan 4
authentication open
authentication key-management wpa
guest-mode ?????
Why we need guest-mode command in above config?
Linksys Wireless Router :: WRT120N Not Accessing Internet With Laptop
Jul 9, 2011I just connected my WRT120N router to the modem of my Cable provider. Everything seems to work well, however every 1-3 days I cannot access internet anymore with my laptop. When I press "IP address release" button in the router settings everything seems to work fine for again 1-3 days. Is there any way I can prevent this from happening all the time?
View 1 Replies View RelatedCisco WAN :: How To Connect 1811W In Internet Modem
Oct 19, 2012I am having a hard time connecting my router into a internet modem since my modem is giving its own private ip address in short the modem is a router in itself. in addition, I cant change the modem's dchp pool its fix with 192.168.1.0 network.
View 3 Replies View RelatedLinksys Wireless Router :: WRT610N Displays Garbage When Accessing Page In Internet Explorer
Mar 26, 2013Linksys WRT610N displays garbage when accessing the "Wireless Page" in Internet Explorer (from Windows 7 or Windows 8)My issues is simmilar to one reported here: url...Accessing my Linksys Wireless Router model WRT610N using IE opening "Wireless" page displays full screen of garbage characters (looks like chinese).
View 2 Replies View RelatedOne Cisco 2811 Router Accessing Internet Through Another 2621?
Apr 26, 2012I have a cisco 2811 router doing nat on my home network and it works fine.I've connected a cisco 2621 router to the 2811 both have serial T1 cards, I have enabled IP routing on both and have eigrp 1 process running. I can ping and telnet to each router and they are advertising the networks on each other. when i do a traceroute on the 2621 to an outside address or name example [URL]I get no reply.
View 4 Replies View RelatedBlock Wired Computer From Accessing Internet Through Router?
Feb 9, 2011how to block a user from using the internet when they plug their computer into a router. My roommate has refused to pay her share of the internet and, being a college student, I don't have enough money where I feel generous enough to let her have free internet after stiffing me. Basically, I have 2 routers at the moment (hoping to fix this soon): my Qwest modem works as a router but I also have a Linksys router connected to it. The only phone jack is in her room so I have no way of stopping her from plugging her computer straight into the modem and/or router. I've configured the wireless so that she would be unable to access the, wirelessly but I'd like to know how to prevent her accessing the internet when she plugs her computer directly into either component.
View 2 Replies View RelatedD-Link DIR-615 :: Connecting Router Accessing No Internet Connection?
Oct 19, 2011So i have set up my Dir-615 router and it worked for about a week perfectly. Then one day i was able to connect to the router, but it says that there is no internet connection. This is untrue since i am able to connect to the internet if i unplug from its WAN port and put it straight into my laptop.
View 8 Replies View RelatedNo Internet Access - Setting Up Wireless Router?
Feb 8, 2012Im trying to set up a wireless router in my dorm room. I know, I am not supposed to do that. I got it set up and everything, but still didn't have internet access.
View 1 Replies View RelatedSetting Up Wireless Router To College Internet Connection ISP
Aug 31, 2011Just moved into apartment in Ann Arbor and am forced to use this ISP. They are not wireless friendly. Their manual sucks and will only provide tech support for $80/hour. I bought a Belkin router and got it working for my MacBook. BUT my roommate can't connect, even tho her MacBook sees the network. And I can't print to my wireless printer even tho it says everything is fine when I run the wireless diagnostics.The ISP has these rules:
- Only connect the router to the Internet or Wan port. Do not connect to the numbered ports (how do I know whether or not I've done that?)
- Do not use static IP addresses
- Do not run a DHCP server
Cisco Switching/Routing :: Unable To Delete Static Route 1811w Router
Nov 23, 2012On 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies View RelatedLinksys Wireless Router :: E2500 Setting Internet Subnet To 255.255.0
Oct 29, 2011Due to the way I have my DSL and VOIP TA configured I need to be able to set the subnet mask in the Internet connection. I am currently using the Static IP, putting in an IP of 192.168.1.x with the subnet of 255.255.0.0 when I try to do this it gives me an error saying that 192.168.33.1/255 is reserved for the guest network. I am not using the 33 at all ANYWHERE. If I change the subnet to 255.255.255.0 it will save but I can't connect to the internet with it. My router I just bought today is the E2500 I have an old Linksys WRT model that worked fine with this exact setup for several years before it crashed on me.
View 3 Replies View RelatedCisco Wireless :: Accessing Internet From Laptop After Installing AIR-LAP1142N-A-K9 AP
Mar 29, 2012I have trouble accessing the internet from my laptop after installing Ciso AIR-LAP1142N-A-K9 AP.The AP are connetected to my router (which has a DHCP enabled) via a switch and each has a Fix IP address with network mask, gateway and DNS already configured. When I triy to connect to the access point, only the IP address and network mask are automatically assigned to the my laptop. and I have to manually input the gatway and DNS to be able to navigate the internet. I would like to know which configuration will allow any node that tries to connect the internet via the access point to be automatically configured to access the internet after authentication.
View 4 Replies View RelatedNetgear N900 Wireless Adapter Not Accessing Internet?
Sep 9, 2012I have finally got netgear adapter to connect to router, and its connected, but not able to access any webpages. I am not receiving any bytes back. I had to manually type in a IP address, as it was not picking it up automatically. I have other devices connected to the router (laptop, ipad, iphones) and access web easily. I have tried hard resets, and shut downs all with no avail
View 14 Replies View RelatedCisco Wireless :: Sh Dot11 Associations Client Command On 1811w?
Oct 23, 2012Wireless is working ok on 1811W.Need to know from command output below what values are considered good for power and signal strenghts
1811w#sh dot11 associations all-client
Address : 40fc.894e.c48c Name : NONE
IP Address : 192.168.98.2 Interface : Dot11Radio0
Device : unknown Software Version : NONE
[code].....
Also what is Association ID mean in above output?
TP-Link 150Mbps Wireless :: WR740N Accessing Internet In Mobile
Mar 7, 2013Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : Lexus
I am using tp link router for accessing internet in my laptop and mobile. everything is opening in my laptop but i had few problems when using internet in mobile. im using android mobile. when using play store the images and screen shots of applications are not loading but im able to download. I'm unable to see the images in play store. So I'm thinking that there is something problem in router settings.
Cisco :: 1811W Stopped Allowing Wireless Connection Of Domain Laptops
Nov 8, 2011I have a Cisco 1811W that after several years in service suddenly stopped allowing any wireless connection to laptops on the domain. It allows hard wired connections and devices that are just using the wireless hot spot like iPads and Iphones but not devices on the domain. These same laptops connect wirelessly without issue at our other facilities which use the same hardware.
Here is the config file of the router in question...
router#show run
Building configuration...
Current configuration : 11776 bytes
[Code].....
Cisco WAN :: Setting Up 2801 As Internet Router
May 31, 2011I'm having trouble setting up a Cisco 2801 as an internet router between our firewall & our ISP.I've setup FastEthernet0/0 as the WAN port & FastEthernet0/1 as the LAN port. I've setup a default gateway pointing the next hop (the ISP),when I plug in a pair of laptops configured to mimic our IP scheme, I'm able to ping thru, but when I put the router between our firewall & ISP I'm not able to get out to the internet (can't ping google) I can still ping the next hop.,Our old router died, so I am unable to pull up its configuration. Here is the code I'm come up with so far.
View 6 Replies View RelatedAccessing Internet Over LAN?
Jan 31, 2011my sister is having a pc in office which is connected to another pc (having net connectivity) over LAN. she is getting the LAN icon in network connections. till today she could not access internet on her pc.but today an engineer came, and changed proxy address or something in internet options>connections>lan settings and accessed internet. after he was over, he again changed something in lan settings and went away. now my sis is not able to access internet. what can i do
View 4 Replies View RelatedCisco WAN :: 1811W Connection Won't Come Up
Jul 24, 2011Cisco 1811 device. Working great with connection from TWTELCOM, trying to add 2nd connection from BRTHOUSE set SLA's and metrics but config still isn't working. The connection won't come up and when I do show ip route ip address it doesn't show a metric so neither connection has a priority and the connection fails. I want brighthouse to have priority as shown with SLA's but if brighthouse fails I want it to go back to twtelcom. [code]
View 1 Replies View RelatedAccessing Two External Storage Devices On One Wireless Router
Feb 5, 2012We have a D-Link DIR655 wireless router on our network. I have purchased two Seagate 1TB network storage units and would like to have one for me and one for my wife. It seems that the router will not support two, because they try to access the same port. How can I plug these two storage units to the router and have access for each of us to one device?
View 2 Replies View RelatedLinksys Wireless Router :: Accessing FTP Using EA4500 Storage?
Jul 3, 2012I have a 1TB Western Digital drive connected to my home EA4500 router. Connecting to media server using SMB protocol (192.168.1.1) works fine. I am moving abroad for an extended amount of time, though, so I would also like to connect to this USB drive using FTP. Using the new Cisco Connect Cloud interface, I have enabled FTP sharing for the USB storage device with port 21 and using standard UTF-8 encoding. Whenever I try to connect to the FTP server using my router login credentials, I get the following error message:"There was a problem connecting to the server xx.xxx.xxx.xx. This file server will not allow any additional users to log on. Try to connect again later"
View 9 Replies View RelatedLinksys Wireless Router :: WRT54G Accessing Websites?
Apr 8, 2012I use a WRT54G wireless router connected to Mac. All of a sudden, I became unable to access certain websites on my iMac, such as Facebook and Apple homepages. But i can access Yahoo website. I tried resetting my linksys setup but it doesnt solve the problem. When i access my iphone via wifi at home, i am also unable to go into app store, facebook app, and emails with images won't load. I also cannot link my iphone to itunes on my iMac. What happens on my computer when I surf the internet is that the page just loads halfway and stop "responding". But my imac airport says that my internet connection is fine, however my access has become very "restricted".
View 1 Replies View RelatedLinksys Wireless Router :: Accessing Wrt320n Across Network?
Aug 7, 2011I've got the below setup, have the wrt320 setup as a switch / wifi ap, i'm totally unable to access its management page from pc1 but am able to via pc 3, why is this, how can i get around this? Routing? Also am unable to access pc3's resources from pc1..When i enter the ip of the wrt320 it thinks about it and before it has come up with the user/password screen but it soon dissapears and firefox comes up with a "Unable to connect Firefox can't establish a connection to the server at 192.168.0.2." message.
View 1 Replies View RelatedLinksys Wireless Router :: EA2700 Not Accessing Web Interface
Jan 24, 2013I am not able to access the web interface of the router.No, i am not using cisco cloud or smartlink .. yes, it has the latest firmware (Ver.1.0.14.129982).Yes, I might be able to get to it if i shut down the router and turn it on again a few minutes later, but the problem is.. why? why do i have to interrupt connections and not have internet to log into the admin web interface of this device? Is there a known problem with it that makes the webservice go down?.. or to take extremely long to respond and thus the browser to quit on it throwing an error?
View 3 Replies View RelatedLinksys Wireless Router :: E4200 / 54G - Accessing LG NAS From Outside Of Home
Oct 3, 2011I was running a Linksys cable modem and 54G with dd-wrt. I had an LG NAS hooked up and everything was working great. I recently upgraded to the Motorola SB6120 and the Linksys E4200. I can not access my LG NAS from outside of my network now. UPnP is enabled, port forwarding is enabled, but I must be missing some other setting that is blocking me from accessing it from work for example.
View 3 Replies View RelatedAccessing System From Internet?
May 7, 2012I want to access my system from internet. My network scenario is as follows;
Internet ==> DSL Modem(s) ==> Load Balance ==> Gateway Firewall ==> My PC DSL 1 : ZXDSL 831CII (Fixed IP)DSL 2 : HG510a Load Balance : TL-R480T+Gateway Firewall : pfSense (BSD)
Accessing IP Camera From Internet?
Jul 19, 2011I just installed WIFI wireless camera in the house. I validated that I can access and view video within home WIFI network. However, I can't seem to access it remotely outside my home Wifi. I follwowed the instruction - found my IP address xxx.xx.xx.xxx : 85 and set port forwarding to 85 to IP camera.
View 3 Replies View RelatedZTE DSL Modem / Wireless Router - Accessing Office Computer From Home PC?
Feb 25, 2013I want to acccess my office computer from Home PC.I have ZTE DSL Modem + Wireless Router and got new Static IP, so how to configure Static IP From BSNL.
View 3 Replies View Related
