Cisco Wireless :: Difference Between AIR-SAP2602-x-K9 With Lightweight IOS And AIR-CAP2602-x-K9?
Jan 30, 2013Is there any difference between AIR-SAP2602-x-K9 with lightweight IOS and AIR-CAP2602-x-K9?
View 3 Replies
ADVERTISEMENT
Cisco Wireless :: 5500 - How Does Lightweight AP Gets Configuration From WLC
Jul 15, 2012Our client have cisco 5500 Wireless lan controllers. They connect to core switch and other ports conenct to various switches on each floor. Then we have cisco AP 1300 series mounted on celing. I was reading that lightweight AP gets config from WLC as soon as they plug in. Need to know how the AP gets config from WLC switches?
View 8 Replies View RelatedCisco Wireless :: Getting Air-lap1042N-E-K9 Lightweight To Autonomous?
Mar 4, 2012I have a air-lap1042-n-e-k9, how to put this wi-fi mode autonomous ?
View 5 Replies View RelatedCisco Wireless :: Status Led AP 1250 Lightweight?
Sep 16, 2012a few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies View RelatedCisco Wireless :: 3502i Autonomous To Lightweight?
Apr 28, 2013how to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.
Cisco Wireless :: Convert A 1602i From Lightweight To Autonomous?
Feb 28, 2013how to convert a 1602i AP from lightweight mode to autonomous?
View 3 Replies View RelatedCisco Wireless :: Converting 2602 From Lightweight To Autonomous?
Feb 19, 2013I have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
Cisco Wireless :: AP 1041N Upgrade To Lightweight Firmware?
Mar 24, 2013How can I upgrade my 1041N AP to lightweight firmware? I found an upgrade tool which works in only XP and 2000 machines. I do not have these outdated OS so is there another way to upgrade it to lightweight?
View 2 Replies View RelatedCisco Wireless :: 1042n Configured As WGB In Lightweight Environment
Nov 8, 2012Here is what I am attempting to do.
1. I have a 1042N AP configured as a Workgroup-Bridge attaching to a Lightweight Access Point.
2. LWAPP AP is on a 5508 series Controller.
3. I have MAC Authentication configured through an Ciso ACS box running 5.2 code. And that portion is working.
4. I want to lock this WGB down even further with a second layer of security. I am thinking WPA2 -AES.
Cisco Wireless :: 1811W Router - Convert To Lightweight?
Nov 11, 2012We have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I am running
WCS 7.0.230.0
WLC 5508 (same code)
Cisco Wireless :: Upgrade Aironet 3502i To Lightweight?
Nov 15, 2011How to upgrade C3502i to Lightweight? I failed to upgrade using Upgrade tool v3.4. The error message is "AP model is not supported" . how can I upgrade it?
View 9 Replies View RelatedCisco Wireless :: AP 2602i - Convert Autonomous AP To Lightweight?
Nov 10, 2012Is it possible to convert an Autonomous AP 2602i to Lightweight just changing firmware as the first generation Aironet APs?
View 2 Replies View RelatedCisco Wireless :: Convert Autonomous 1142N To Lightweight?
Apr 15, 2012Apparently converting autonomous 1142N to lightweight is not supported by ether WCS 7.0 or the Upgrade tool. The option is to do it manually with CLI, but there is about 200+ AP's that need converting. We can't do them all at the same time. We have to do it building per building.
View 4 Replies View RelatedCisco Wireless :: 1041n From Autonomous To Lightweight - Error
Apr 30, 2012Doing the firmware upgrade on a 1041n AP from Autonomous to Lightweight. Downloaded from Cisco, checked MD5 and got a match so went and upgraded. Upgrade went find etc.. and rebooted. When I reboot I get the following error and then rubbish text
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x0000018a
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
[code]...
I rolled back to the autonomous OS and all ok and AP operates as normal. When on the lightweight IOS I can get a telnet response but cannot access as it states Password require but not set.
Followed this process to upgrade [URL] and followed this process to restore to Autonomous: [URL] why it's not working.
Update: Just tried another AP same result. Downloaded Lightweight again and same result
Here is the CLI upgrade process
examining image...
Loading c1140-rcvk9w8-tar.124-21a.JA2.tar .from 172.16.4.114 (via BVI1): !
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1140-rcvk9w8-mx
[code]....
Cisco Wireless :: AIR-AP1220B Lightweight Conversion / WLC Support?
Mar 24, 2013Is AP 1220B (b-only radio) supported for registration to WLC (7.0.x) with Lightweight software? I've managed to convert the AP to Lightweight mode, but I could not get it to register with WLC 2504 (software version 7.0). Is it possible that this AP is only supported if changing the in-built radio module?
In the compatibility matrix [URL] there is an information that this AP is supported on WLC up to version 7.0.x. On the other hand it is not supported by Autonomous to Lightweight Mode Upgrade Tool [URL] Since these APs does not have pre-installed MIC, it is mandatory for them to create Self-Signed Certificate (SSC). Upgrade tool could do this job (along with adding the created SSC hash to the authorized list on WLC), but it does not support this particular AP/radio. If I do the conversion manually (archive download-sw ...), the AP does not have the SSC needed for communication with WLC. I've tried making the SSC manually (instructions found on this site [URL] while AP is autonomous mode, and then converting it to Lightweight, but the AP still could not register to WLC.
In the debugs (on WLC/AP), I am receiving an error that is described in some Cisco troubleshooting documents as something related to WLC not having an SSC hash in the auth list. Problem is that the AP is not even sending standard CAPWAP messages and there is nothing to be seen in "debug pm pki enable" on WLC...
Cisco Wireless :: AIR-LAP1242G-A-K9 - Devices Keep Disconnecting From Lightweight APs
Jun 12, 2012I have several Lightweight APs (AIR-LAP1242G-A-K9) runing of a single WLC. We keep getting devices, sometimes all devices, losing network signal. The WLC is running a global power setup so all APs have their power set automatically. The setting for power parameters are default. I have noticed when I run a client test the APs run at 11Mbps while the client devices run at 50-54Mbps. The protocol used by both devices is 802.1G. These network drop offs are frequent and I should say may well be an issue with the client devices although there are several different types of devices experiencing this issue. My question is should the TX and RX rates be the same? Is it ok to have this disparity in the TX/Rx values?
View 7 Replies View RelatedCisco Wireless :: Air-ap1142n-ek9 / Requirements For Autonomous To Lightweight AP Conversion?
May 21, 2012is there any issue in buying air-ap1142n-ek9 802.11A/G/N FIXED AUTO AP INT ANT and later on converting it into lightweight under the control of air-ct2504-15k9 2504 WIRELESS CONTROLLER WITH 15 AP LICENSES ?Are there any requirements on the SW of the WLC and the IOS of the AP? The reason of the choice is budget.
View 1 Replies View RelatedCisco Wireless :: Upgrade AP1262N To LAP1262 Autonomous To Lightweight?
Jul 12, 2012This is one of our first site where we are implementing Cisco wireless, and we bought some external Autonomous AP1262, when we should have bought Lightweight LAP1262 . We can get those replaced, but I am looking into migrating them in order to get them to register with our 5508 controllers.
There do not seem to be a migration tool to download for 1262. Must it be done via the WCS ?So far I have not managed to add these autonomous AP to the controllers. How to know if a migration toll exists for those !
Cisco Wireless :: Bridge Autonomous 1252 AP To Lightweight WLAN
Aug 22, 2011I have a Cisco WLC 5508 managing several 1252s in lightweight mode. There is a portable across campus that has a standalone network but no cabling to tie in to the corporate network. I have another 1252 that is in autonomous mode. Could I essentially configure that as a bridge with the same security and SSID in order to bridge the corporate WLAN? If not, what are my options?
View 4 Replies View RelatedCisco Wireless :: Convert 1041 In Autonomous AP Mode To Lightweight?
Apr 20, 2012Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies View RelatedCisco Wireless :: 5508 - Lightweight APs Not Receiving IP Address Following Controller Upgrade?
Apr 3, 2013I have a 5508 controller, just upgraded from 6.0.182 to 7.0.98.0. Also LAG was switched off directly after upgrade.
Since the upgrade none of the 1142 LAPs are associating with the controller. I can see they are being issued IPs by the internal DHCP but putting a console cable and watching I am getting:
Not in Bound state.
*May 4 11:41:17.759: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*May 4 11:41:17.759: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
One Ap prior to the upgrade was on a static IP and that connected through without any problem, (it was an 1131 though, but I dont think that is the issue...)
Cisco Wireless :: 262N Lightweight Access Point Work With 4402
Apr 4, 2012Does the Cisco 1262N Lightweight Access Point (AP) work's with Wireless LAN Controller 4402?
View 1 Replies View RelatedCisco Wireless :: What 113X AP Model Will Work In Autonomous And Lightweight Mode
Feb 4, 2013What 113X AP model will work in Autonomous and LightWeight Mode? I want to buy some 113X AP's for my lab and want to make sure I don't get stuck with the ones that only run in one mode. I am looking at buying this one AIR-AP1131AG-N-K9 802.11a/b/g. Will this model work in both modes?
View 1 Replies View RelatedCisco Wireless :: WLC 5508 - Lightweight AP Client Getting Wrong IP Address From DHCP Server
Mar 29, 2012I have 2 units Cisco WLC 5508 running software version 7.0.220 with 70 over units Cisco AP 1262N and 1242AG. Some of wireless clients having problem to get the correct IP address from the DHCP server. There are 2 units of Microsoft DHCP. Both DHCP server ip have been configured on the Interface at the WLC. The core switch also being configured with ip helper. I've attached the debug output of one of the wireless client during the problem.
View 12 Replies View RelatedCisco Wireless :: AIR-CAP3502I-N-K9 - Change Regulatory Domain On Lightweight Access Point?
Mar 22, 2012I'm wondering if there is an easy way to change the regulatory domain on a lightweight access point. The reason I'm asking is someone accidentally placed an order for AIR-CAP3502I-N-K9 access points instead of the AIR-CAP3502I-A-K9 flavored ones. I can see how it happened, since undoubtedly someone asked for the "N" access points, thinking 802.11n, and the other person was thinking AIR-CAP3502I-"N"-K9.
do I have to RMA them, or is there a way to magically turn them into the ones flavored for the Americas?
Cisco Wireless :: AIR-AP1231G-E-K9 - Upgrading Autonomous Access Points To Lightweight Mode
Jun 6, 2013I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies View RelatedCisco Wireless :: 1142 - Lightweight AP Template / Flex Connect Parameters Error
Jul 9, 2012I created a LAP Template in NCS to configure some new 1142 LAPs that were installed in a remote office. These LAPs need to be in Flex Connect mode with V LAN support. The template is being applied with partial success on every access point. Details of the partial success say the Flex Connect Parameters fail with the following error.
Provision Failure: { URL}.Object Not Found Exception cannot be cast to [URL]
Am I doing something wrong? The Flex Connect portion of the template has V LAN Support enabled, Native V LAN ID, and the Profile Name- V LAN Mappings configured.
Prime NCS version 1.1.1.24 Access Points are AIR-LAP1142N-A-K9s running 7.2.110.0
Cisco Wireless :: Reset 1522 Series Lightweight Access Point To Factory Default?
Jan 13, 2013I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies View RelatedCisco Wireless :: 5508 - DHCP Option 43 For 1130 And 1300 Lightweight Access Points?
Mar 14, 2013I have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller. If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points? Can these access points works with LWAPP or do i need to configure CAPWAP?
View 4 Replies View RelatedCisco Wireless :: 1310 Point-to-point Bridge In Lightweight Mode?
Apr 24, 2011how is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
Cisco Wireless :: AP 1041 Conversion From Autonomous Mode To Lightweight Mode
Mar 4, 2012We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode.
View 1 Replies View RelatedCisco Wireless :: Maximum Code Level For Lightweight 1130 / Minimum WLC Code For 1600 Series APs?
Feb 19, 2013I have been searching through the cisco docs for a while and i just cant seem to find this info. Can I run aironet 1600's with my wism running 7.0.116? Also, could I run my 1130 series ap's with a wism2? Basically, what is the minimum code level for a lightweight 1600, and what is the maximum code level for a lightweight 1130?
View 3 Replies View RelatedCisco :: 1242 Autonomous And / Or Lightweight
Jan 17, 2011I have some 1242s and I can't get a straight answer on whether they can do both autonomous and lightweight or just lightweight.
Model number: AIR-LAP1242AG-A-K9.
I'm assuming that the 'L' in the model numbers means it's just lightweight, but searching Cisco's site and the Internet in general it's just not clear.
I know it works as a lightweight AP, can I run it in autonomous mode?