I purchased a new ap1041n access point. It's the first Cisco I've tried to configure in a long time. I'm trying to get the 802.11n working but it seems to be stuck in 802.11G since I can only get it to go up to 36mb. The radio says its running in mixed mode and I can't figure out if that means b/g or b/g/n. I ran the Express Setup and it didn't seem to work.
View 5 Replies
We are in need to perform a site survey with the Aironet 1041N Access Point.
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?
I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?
View 1 Replies View RelatedHow do you reset a 1252ag access point that has the mode button disabled?
View 2 Replies View RelatedWe have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings. One went south on us & we placed it. Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP. Now, we can't connect or even ping either AP. And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them. I'm attaching the configuration. Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?
View 3 Replies View RelatedI have a Catalyst 4006 with Supervisor II engine. I have 48 port 10/100/1000 blades installed in it for connection to my servers. I am having a lot of problems with performance when connecting servers that are using 100 MB NICs. The speed of the connection is really bad. I have attempted setting the ports and NICs to 100MB Full duplex instead of auto-detect, but still get the same results.
I also have a 10/100 quad-port card installed in a NetApp filer. All four ports are trunked together and connect to 4 ports in the Catalyst. The ports in the Catalyst are trunked using the Port Channel feature of the CatOS. When I look at the port statistics on 3 of the 4 ports from the quad-card, there are a ton of runts and errors (both transmit and receive). The 4th port is fine, no errors.
I recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.
The reason why I'm writing is because I have a few questions to clarify.
1) What is the best position for better signal, top side wall or corner ceiling?
2) How many client mac address filtering can i do per access point?
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.
4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)
5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?
6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?
7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.
8) Can CCp software be used in these access points?
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
We are currently running WCS but have built a new Prime Infrastructure 1.3 system from scratch on a brand new server, we have sucessfully migrated the old WCS database on to the new Prime server and as a test I have pointed 1 anchor controller to it. Possible to point the WLC's to both WCS and Prime Infrastructure concurrently - I was thinking that it would be a quick fallback if we has any problems with Prime (I know there have been some!) We are not running MSE but we do have mobility groups, the WLC's are 5508 running 7.0.235.3 .
View 0 Replies View RelatedWhat I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedWe have a pretty good sized church and gym and we're thinking about getting three 1041n to cover the whole area. If we setup all three exactly the same, with the same ssid and password, but just put them on different channels, will our devices automatically hop from ap to ap as we walk around? Is there anything special we should do to make them work better together?
View 1 Replies View RelatedI am using AIR-LAP 1041N-A-K9 wireless Accesspoint it was controlled by using the Air-CT2504-k9 Wireless controller. When I tried to connect the access point using Windows 8 machine it was not able to connect
View 8 Replies View RelatedHow can I upgrade my 1041N AP to lightweight firmware? I found an upgrade tool which works in only XP and 2000 machines. I do not have these outdated OS so is there another way to upgrade it to lightweight?
View 2 Replies View RelatedWe have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
how to enable wireless N speeds on this access point? It's operating in mixed mode via PoE. If I go into network interfaces -> Radio0-802.11N --> Settings, the highest data rate is only 54 mbps. Can N speeds be acheived in mix mode? Also, I thought this access point is dual-band, but I'm only seeing the one radio, is that normal? (see attached image)
View 9 Replies View RelatedDoing the firmware upgrade on a 1041n AP from Autonomous to Lightweight. Downloaded from Cisco, checked MD5 and got a match so went and upgraded. Upgrade went find etc.. and rebooted. When I reboot I get the following error and then rubbish text
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x0000018a
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
[code]...
I rolled back to the autonomous OS and all ok and AP operates as normal. When on the lightweight IOS I can get a telnet response but cannot access as it states Password require but not set.
Followed this process to upgrade [URL] and followed this process to restore to Autonomous: [URL] why it's not working.
Update: Just tried another AP same result. Downloaded Lightweight again and same result
Here is the CLI upgrade process
examining image...
Loading c1140-rcvk9w8-tar.124-21a.JA2.tar .from 172.16.4.114 (via BVI1): !
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1140-rcvk9w8-mx
[code]....
Cannot access configuration page for WAP11 Access
View 9 Replies View RelatedI have a 877W router and a ASA5505 firewall. If I purchase a Smartnet contract for 877W router, I take it this give me access to download newer IOS for router?
Does it also give me access to ASA5505 downloads? Or do I have to purchase a seperate Smartnet for it to access ASA downloads?
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies View Related
