Cisco Wireless :: 1552 MAP Can't Join Network Through RAP

May 6, 2013

I have configured a 1552, that is wired to network, as "Bridge" then "RootAP".
After reboot, I can see a MAP trying to join the network, in the "simple" logs of the controller :
"Mon May 6 17:29:43 2013   Mesh Node '04:da:d2:1f:4d:6f' failed to join controller, MAC address not in MAC filter list."
As I have done for the RAP, I enter this MAC address in the MAC Filtering area under Security tab. But this action doesn't solve the problem, I continue to see this message in the controller logs !
If I open a SSH session on the RAP, I can see this block of debug messages repeat all the time :
*May  6 15:29:33.163: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 dot1x control
*May  6 15:29:33.167: %LINK-6-UPDOWN: Interface Virtual-Dot11Radio0, changed state to up
*May  6 15:29:34.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Dot11Radio0, changed state to up
*May  6 15:29:43.223: %MESH-6-LINK_UPDOWN: Mesh station 04da.d21f.4d6f link Down
*May  6 15:29:43.423: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 going
When I take a look into detailled debug messages of the controller I can see this :
*spamReceiveTask: May 06 17:30:44.364: #LWAPP-6-RADIUS_AUTHORIZATION: spam_radius.c:242 The system could not send join reply, AP authorization failed; AP:04:da:d2:1f:4d:6f
I don't know why the system talks about dot1x or Radius Authorization, and if this is the source of my problems. On a other hand, I can see in the debug messages that there is a 2 hours lag time between controller (correct time) and RAP (incorrect, I suppose it synchronize with the controller?)

View 25 Replies


Unable To Join Network On Wireless Router?

Jul 26, 2011

ISP: CharterType: CableRouters: Belkin N150 & Linksys E1200Devices: Laptop, ipad, desktop w/wireless card, hardwired desktopI had random issues with the Belkin router. I was able to hard-wire connect via the router but very randomly my wifi signal would go out and I would be completely unable to connect to the router on any device. Now I am having the exact same issues with my new Linksys router.Sometimes the wifi works and others I get "Unable to connect to network" or "Unable to join network". I have not yet noticed a pattern.Here are the things I have tried:

* Replace router with new router
* Remove encryption
* Change encryption types
* Restart both cable modem & router
* Factory reset of router
* Changed Channels
* Reboot of router from interface than mine) are all called 2WIRE490 and 2WIRE593.

View 11 Replies View Related

Cisco Wireless :: Can't Set 1552 To Use 802.11a 40 MHz Channels

Apr 22, 2012

I am testing a Cisco 1552 and cannot seem to set it to use the 40 MHz channels. In the controller GUI is is set to use 40 MHz channels under DCA for 802.11a but when I go into the CLI and show the config of the AP it shows the channel width to be 20 MHz. If I try to change the channel width through the CLI I get "radio is not disable or ap not set to customize" or something like that. The radio is disabled globally and locally. Is there a way to set the AP or radio to a "customize" mode?
What prompted this was I was testing the throughput on it and can only get a 130 mbps data rate connection to it. The data sheet says it will support 300 mbps with the 40 mhz channel so I was trying to test it atteh higher rate.The HW is a Cisco 4402 with 7.0.230 software on it, 1552E.

View 3 Replies View Related

Netgear Adapter Will Not Join The Wireless Network And Keeps Timing Out

May 24, 2012

My Netgear adapter will not join the wireless network and keeps timing out.

View 3 Replies View Related

Cisco Wireless :: Connecting 1552 LAP With 802.11a Using AIR-CB21AG-E-K9

May 27, 2012

I'm having a small issue using my external CIsco Wireless Card AIR-CB21-AG-E-K9 with a Lightweight Access Point 1552 (Outdoor) using 802.11a Radio.
Description of issue :
I can connect to a wireless network when i set the Wireless Mode to 2.4GHz 54 Mbps (802.11 g), and 2.4 GHz 11 Mbps (802.11 b) on the card but not with 5GHz 54 Mbps (802.11a).
Note that this card is compatible to 802.11 a, b and g.
All settings on the 2504 WLC is set to default regarding the radios configuration.
Both radio interfaces type (802.11 b/g/n and 802.11a/n) are operational and Admin status Enable on the WLC.
The status of the wireless card is as follows :
Profile Name - Wifi-Test
Link Status - Not associated
Wirless Mode : 5 GHz 54 Mbps
Network Type : Infrastructure
Current Channel : Scanning

View 3 Replies View Related

Cisco Wireless :: AP 1552 In Mesh Mode (MAP)

Sep 14, 2012

I'm trying to become famillar with Cisco Mesh AP's deployment. As I know RAP's (Roof-top AP's are AP's with Ethernet/Fiber connection to the network). I connected these AP's via L2 switch , they can reach WLC and everything looks fine.
No I want to connect few MAP's to my RAP's. But of course firstly we will need to set-up IP addresses for these MAP's? But how? There is no "configure terminal" option at all ( on mesh AP console) .
Exec commands:
access-profile   Apply user-profile to interface


View 21 Replies View Related

Linksys Wireless Router :: WRT54GH - Unable To Join The Network?

Aug 31, 2010

Ive been using this router for about 4 months now. suddenly it wont let me connect wirelessly through itouch nor through imac. it says Unable to join the network "linksys" eventhough "linksys" is indicated to be an available WIFI network and that signal is full. Problem is still the same even after i reset the router a couple of times pass 30seconds, set the security to No Password.if i connect the router with a cable it connects seamlessly and allows me to go online.

View 8 Replies View Related

D-Link DIR-655 :: Configure To Join Existing Wireless Network As Repeater

Jan 29, 2011

I'd like to give my DIR-655 (rev. A4, firmware 1.32) to my brother for use as a repeater, to work with the weak signal in his apartment.  But I don't see any way to configure the device to join an existing wireless network.  Am I wasting my time?

View 7 Replies View Related

D-Link DIR-615 :: Cannot Get Wireless Items To Connect / Says Unable To Join Network

Apr 14, 2012

I reset my Dlink 615 wireless router.  I held down the power and reset for 30 seconds and rebooting the system with the disc.  I did change the router name, but believe everything else stayed the same.  My desk top is working fine being "hardwired" but nothing wireless will connect.

I did see this time it installed Network Magic which I have since uninstalled and again rebooted the computer system and still cannot get the wireless to work.  It shows the network available, but my password for some reason does not take.

View 1 Replies View Related

Cisco Wireless :: 1552 Outdoor AP Disappears From WLC5508

Dec 30, 2012

My problem ist that i have 4 air-cap-1552e APs witch are powerde trugh Power Injectors. They worked fine for a few days but then the controller ( lose connection to them. Right now i have only one Joined AP. The other 3 are status not joined. I can Ping all 4 Aps and wifi clients are connected through them.

View 8 Replies View Related

Cisco Wireless :: Mixing 1522 And 1552 Outdoor AP

Jun 13, 2013

Client has existing 1522 outdoor access points over different branches.1522 is dicontinued and 1552 is the replacement AP.Client intends to extend their outdoor wireless with the new AP's.Are there any known issues if the 1552 is mixed with 1522 envi?,Is a separate controller required for the new AP's?Will MESH work between 1522 and 1552 AP's?

View 3 Replies View Related

Cisco Wireless :: Configure A 1552 AP Over CLI To Bridge Mode

May 26, 2013

a customer got an 1552 outdoor AP in local mode and installed it at a building. It has to run as a Mesh AP (MAP). Now the AP connects one time to the WLC 5508 and started a download. After that, the AP never came back. Like we saw on the other installed 1552 RAP's, they all where in local mode.We configured all AP's to bridge mode, but the MAP could not join anymore.Is there a CLI command to change the mode on the AP itself?From the WLC it's not a problem, but for the AP CLI I cannot find sth.

View 1 Replies View Related

Cisco Wireless :: AP 1552 Is Equivalent Of Local Mode?

Jun 24, 2012

I found this sentence in 1552 AP guide."AP1552 comes only in the Bridge mode and the mode cannot be changed. A mesh access point performs CleanAir function and also serves clients on the assigned channel similar to the way the Cisco Indoor CleanAir AP3500 (nonmesh mode) operating in LMAP mode serving clients on its assigned channel. The mesh AP also monitors the spectrum only on that channel."We want to use this AP as a local AP ( not for mesh deployments) and serve our wireless clients. The main thing why we need this is just operating temperature. Is it good choice? Does it will function as "normal" local AP or we will have any problems , because of that "mesh" mode?

View 12 Replies View Related

Cisco Wireless :: 1552 RAP-to-RAP And Maintain Redundancy With Connection To WLC

Feb 26, 2013

I need to know if i can connect RAP to RAP and maintain redundancy with connection to WLC.
I have one 1552 with the gigabit ethernet connected to the gigabit ethernet to another device that has a point-to-point link with another device where have a ethernet connection with a switch in the same broadcast domain where i have my WLC.
Next to this 1552 i have another 1552 that have the same situation, both with omnidirectional antenna.
I would like to have a Mesh connection with these two 1552 in 5Ghz, because if some point-to-point link is down i need redundancy to the WLC and my network, because i have some clients connected in the 2.4 Ghz in both Access Points.

View 4 Replies View Related

Cisco Wireless :: Setting Channels Supported By 1552

Oct 15, 2012

Couple questions on setting channels on Cisco 1552s. First off almost all locations are fibered and set as RAPs. It doesn't allow me to set the channel assignment method to "global" to use DCA. It says it can't be done for a mesh backhaul AP. Is there any way around this? Next, when the channel is set to "custom" there are only 5 channels listed to choose from in the UNII-3 band. The spec sheet on the 1552 shows it supports other frequencies in the UNII-2 and UNII-2 extended range. Why can't I select those channels?

View 8 Replies View Related

Cisco Wireless :: AP 1552 Operation Status Is Down On WLC 5508

Apr 21, 2013

I want to set up AP 1552 as outdoor access point so serve clients. This AP is connected to 3750X switch and recieving power over ethernet.Now, by default AP 1552 come with bridge mode and it cannot be changed to local mode. I read on one of the post and made it ROOTAP but still the OPER STATUS is down. This device is already registered to my WLC.
what needs to be done to bring the AP in operational status.[code]

View 3 Replies View Related

Linksys Wireless Router :: Unable To Join Network With Iphone And WRT610

Aug 7, 2011

I had PCs, Macs and other devices (iphone, itouch) able to connect fine to the WRT610n.   I moved to an apartment and when I turned the network on all the devices could connect expect for the iphone and itouch.  I have tried turning the wireless security off and MAC filtering off . I get the same "Unable to join the network" message. 

View 7 Replies View Related

Cisco Wireless :: 1552 - Controller Based Mesh Configuration

Jun 26, 2012

I have to install a wireless mesh network shortly using Cisco 1552 APs.  This will be controller based using 5508 controllers.  The controllers currently have some 1262 APs configured in a mesh and bridging configuration so happy that it all basically works.  My question is - what is the "config mesh range' command doing on the controller ( or setting the Range(RootAP to MeshAP) setting on the controller mesh GUI.  The default setting is 12000feet and I have left it at default at present.  Just interested in what this is used for - I assume it alters the mesh protocol parameters somehow ( or the RF parameters perhaps ) as it suggests in the guide that mesh APs will reboot following this command being changed.

View 4 Replies View Related

Cisco Wireless :: Mesh 1552 Link Failover Not Seamless?

Apr 28, 2012

Child  MAP failover to another parent MAP takes 4 request time out (rto). Client  applications also time out and needs to reconnect everytime it  happens. It is a normal behavior for a 1552 ap?

View 1 Replies View Related

Cisco Wireless :: 1552 AP / WLC 7.2 - Mesh Infrastructure (Repeater Fallback)

Feb 14, 2013

I'm deploying a Cisco Mesh infrastructure using WLC 7.2 version and 1552 APs.
This Mesh APs will be connected in the Light Pole and the RAP will be connected to the SP Switch located in this same Pole.
The MAP will be powered using Pole source power and will be connected to the RAP over 5.8 Bach haul.
My Customer asks if is possible that in case of SP Switch lost the connectivity to the Backbone IP, the RAP can connected to another RAP and maintain the connectivity to the Backbone over the Air, like REPEATER FALLBACK mode in Autonomous version.
For that I thinking to change the role of the RAP APs to "MAP with UTP Cable", but I'm not sure that a MAP AP with CAPWAP tunnel over UTP Cable can provide a Down link Backhand to another MAPs. That is possible?

View 3 Replies View Related

Linksys Wireless Router :: EA4500 IPhone Connection Unable To Join Network

Sep 19, 2012

My EA4500 router seems to drop mine and my wife's iPhone wifi connection at what appears to be the edge of my router's range. When we come back in range, our iPhone's intermittently give the error "Unable to join network.". And we're stuck in that mode. When I check the Devices menu in the CCC interface, I notice the iPhone device is configured and still online. However the "x" box to delete the device is greyed out because it's online. So how do I get out of this state and have my iPhone connect

View 2 Replies View Related

Cisco Wireless :: Unable To Console Into 2600 And 1552 Series Access Points?

May 7, 2013

We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).

View 4 Replies View Related

How To Find A Network To Join

Jan 30, 2012

i don't know how to connect to a network, to make an ipad work

View 1 Replies View Related

How To Join A Wifi Network

Aug 9, 2011

Have two wifi in my area but can't get on them what do I need to do

View 1 Replies View Related

How To Get Ipod To Join Network

Jun 20, 2011

how do I get Ipod to join ipad works just fine?

View 1 Replies View Related

Join A Windows Network With Ubuntu

Feb 17, 2011

When I click on Network under Places I can see Windows Network folder. When I click on the Windows Network folder it displays an error message of Unable to mount location...Failed to recieve share list from server.

View 1 Replies View Related

Hamachi Doesn't Create Or Join Network

Mar 13, 2011

I've been trying to get it to work all day.When I open up Hamachi it shows the main screen with two buttons. Create a new network and Join an existing network.I've tried both but when I click create or join it doesn't do anything. Like it actually does nothing at all.Doesn't even close the window.Everything stays open and it doesn't either create or join any networks.

View 1 Replies View Related

Cisco :: 1552 AP Act Like A Switch?

Apr 25, 2012

I know that a 1552 AP has 4 Ethernet ports. Is it possible to use them as some standard switch ports? If I connect two ore more devices to these ports do i have connectivity between them?

View 16 Replies View Related

Cisco Routers :: Join Network With RV016 To Network With RV082 Via Point To Point Air Bridge

Apr 19, 2012

Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA                                LocationB
RV016                                     RV082
WAN1 ADSL modem                WAN1 ADSL Modem
WAN2 DedicatedIP modem       WAN2 Free
WAN3..7 free


We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs  WAN ports? switch ports?  What rules or static routes need to be created?

View 2 Replies View Related

Protocols / Routing :: Can't Connect Three Computer After 4th Laptop Join Network

Jan 21, 2011

My customer has 3 computer

1- Windows xp

2- Win7

3- Apple

4 new sony laptop.

Vaio would not connect using WEP 40-bit key. Logged into Airport Extreme router with Airport setup utility for Windows from Apple. Updated firmware from 5.1.1 to 5.7. Reset Encryption from WEP to WPA/WPA2 Personal.Connected Vaio on Wifi using WPA2. Removed ethernet cable and connection was good at 54MB/s.Completed Windows Update

View 3 Replies View Related

Can't Join New Acer Travelmate 2428 Laptop To Home Network

Feb 25, 2012

Just got a new(secondhand) laptop & have successfully connected it to the internet via my wireless router/modem, but can't get it onto my home network. It appears to work, says it's connected but shows no other computers & they don't show this one.The laptop is an Acer Travelmate 2428, running Win7 Professional. My 2 wirelessly networked PCs are running on WinXP & the printer is connected physically to one of those. The router/modem is an Edimax. In XP it talks about 'home networks' whereas Win7 has 'homegroups'. I've used the wizard to 'manually connect to a wireless network' which is how I networked the PCs. I've also tried all other options in the 'Network & Sharing Centre' including the troubleshooter which when 'troubleshooting network problems' only tells me my clock is not right. In the network & sharing centre under 'view your active networks it says 'home network' & next to homegroup says 'joined'.

View 7 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3220 / IPhone 3G Error Unable To Join Network

Dec 8, 2012

My laptop's wifi is just working fine with TP Link but I'm unable to connect internet via wifi on my iPhone 3G. My iPhone's wifi just works fine in my office. Is there any solution available?

iPhone 3G 8MB
iOS 4.2.1
Modem Firmware: 06.15.00
Router: TP LINK TL-MR3220
Firmware Version: 3.13.12 Build 120524 Rel.60134n

Is there additional setting for iPhone?

View 1 Replies View Related

Cisco Wireless :: How To Join The AP To WLC2500

May 16, 2013

I am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.

WLC: Cisco 2500
IP Address:

View 5 Replies View Related

Copyrights 2005-15, All rights reserved