Child MAP failover to another parent MAP takes 4 request time out (rto). Client applications also time out and needs to reconnect everytime it happens. It is a normal behavior for a 1552 ap?
View 1 RepliesI'm trying to become famillar with Cisco Mesh AP's deployment. As I know RAP's (Roof-top AP's are AP's with Ethernet/Fiber connection to the network). I connected these AP's via L2 switch , they can reach WLC and everything looks fine.
No I want to connect few MAP's to my RAP's. But of course firstly we will need to set-up IP addresses for these MAP's? But how? There is no "configure terminal" option at all ( on mesh AP console) .
MeshAP#?
Exec commands:
access-profile Apply user-profile to interface
[Code].....
I have to install a wireless mesh network shortly using Cisco 1552 APs. This will be controller based using 5508 controllers. The controllers currently have some 1262 APs configured in a mesh and bridging configuration so happy that it all basically works. My question is - what is the "config mesh range' command doing on the controller ( or setting the Range(RootAP to MeshAP) setting on the controller mesh GUI. The default setting is 12000feet and I have left it at default at present. Just interested in what this is used for - I assume it alters the mesh protocol parameters somehow ( or the RF parameters perhaps ) as it suggests in the guide that mesh APs will reboot following this command being changed.
View 4 Replies View RelatedI'm deploying a Cisco Mesh infrastructure using WLC 7.2 version and 1552 APs.
This Mesh APs will be connected in the Light Pole and the RAP will be connected to the SP Switch located in this same Pole.
The MAP will be powered using Pole source power and will be connected to the RAP over 5.8 Bach haul.
My Customer asks if is possible that in case of SP Switch lost the connectivity to the Backbone IP, the RAP can connected to another RAP and maintain the connectivity to the Backbone over the Air, like REPEATER FALLBACK mode in Autonomous version.
For that I thinking to change the role of the RAP APs to "MAP with UTP Cable", but I'm not sure that a MAP AP with CAPWAP tunnel over UTP Cable can provide a Down link Backhand to another MAPs. That is possible?
I am testing a Cisco 1552 and cannot seem to set it to use the 40 MHz channels. In the controller GUI is is set to use 40 MHz channels under DCA for 802.11a but when I go into the CLI and show the config of the AP it shows the channel width to be 20 MHz. If I try to change the channel width through the CLI I get "radio is not disable or ap not set to customize" or something like that. The radio is disabled globally and locally. Is there a way to set the AP or radio to a "customize" mode?
What prompted this was I was testing the throughput on it and can only get a 130 mbps data rate connection to it. The data sheet says it will support 300 mbps with the 40 mhz channel so I was trying to test it atteh higher rate.The HW is a Cisco 4402 with 7.0.230 software on it, 1552E.
I have configured a 1552, that is wired to network, as "Bridge" then "RootAP".
After reboot, I can see a MAP trying to join the network, in the "simple" logs of the controller :
"Mon May 6 17:29:43 2013 Mesh Node '04:da:d2:1f:4d:6f' failed to join controller, MAC address not in MAC filter list."
As I have done for the RAP, I enter this MAC address in the MAC Filtering area under Security tab. But this action doesn't solve the problem, I continue to see this message in the controller logs !
If I open a SSH session on the RAP, I can see this block of debug messages repeat all the time :
*May 6 15:29:33.163: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 dot1x control
*May 6 15:29:33.167: %LINK-6-UPDOWN: Interface Virtual-Dot11Radio0, changed state to up
*May 6 15:29:34.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Dot11Radio0, changed state to up
*May 6 15:29:43.223: %MESH-6-LINK_UPDOWN: Mesh station 04da.d21f.4d6f link Down
*May 6 15:29:43.423: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 going
When I take a look into detailled debug messages of the controller I can see this :
*spamReceiveTask: May 06 17:30:44.364: #LWAPP-6-RADIUS_AUTHORIZATION: spam_radius.c:242 The system could not send join reply, AP authorization failed; AP:04:da:d2:1f:4d:6f
I don't know why the system talks about dot1x or Radius Authorization, and if this is the source of my problems. On a other hand, I can see in the debug messages that there is a 2 hours lag time between controller (correct time) and RAP (incorrect, I suppose it synchronize with the controller?)
I'm having a small issue using my external CIsco Wireless Card AIR-CB21-AG-E-K9 with a Lightweight Access Point 1552 (Outdoor) using 802.11a Radio.
Description of issue :
I can connect to a wireless network when i set the Wireless Mode to 2.4GHz 54 Mbps (802.11 g), and 2.4 GHz 11 Mbps (802.11 b) on the card but not with 5GHz 54 Mbps (802.11a).
Note that this card is compatible to 802.11 a, b and g.
All settings on the 2504 WLC is set to default regarding the radios configuration.
Both radio interfaces type (802.11 b/g/n and 802.11a/n) are operational and Admin status Enable on the WLC.
The status of the wireless card is as follows :
Profile Name - Wifi-Test
Link Status - Not associated
Wirless Mode : 5 GHz 54 Mbps
Network Type : Infrastructure
Current Channel : Scanning
My problem ist that i have 4 air-cap-1552e APs witch are powerde trugh Power Injectors. They worked fine for a few days but then the controller (7.2.111.3) lose connection to them. Right now i have only one Joined AP. The other 3 are status not joined. I can Ping all 4 Aps and wifi clients are connected through them.
View 8 Replies View RelatedClient has existing 1522 outdoor access points over different branches.1522 is dicontinued and 1552 is the replacement AP.Client intends to extend their outdoor wireless with the new AP's.Are there any known issues if the 1552 is mixed with 1522 envi?,Is a separate controller required for the new AP's?Will MESH work between 1522 and 1552 AP's?
View 3 Replies View Relateda customer got an 1552 outdoor AP in local mode and installed it at a building. It has to run as a Mesh AP (MAP). Now the AP connects one time to the WLC 5508 and started a download. After that, the AP never came back. Like we saw on the other installed 1552 RAP's, they all where in local mode.We configured all AP's to bridge mode, but the MAP could not join anymore.Is there a CLI command to change the mode on the AP itself?From the WLC it's not a problem, but for the AP CLI I cannot find sth.
View 1 Replies View RelatedI found this sentence in 1552 AP guide."AP1552 comes only in the Bridge mode and the mode cannot be changed. A mesh access point performs CleanAir function and also serves clients on the assigned channel similar to the way the Cisco Indoor CleanAir AP3500 (nonmesh mode) operating in LMAP mode serving clients on its assigned channel. The mesh AP also monitors the spectrum only on that channel."We want to use this AP as a local AP ( not for mesh deployments) and serve our wireless clients. The main thing why we need this is just operating temperature. Is it good choice? Does it will function as "normal" local AP or we will have any problems , because of that "mesh" mode?
View 12 Replies View RelatedI need to know if i can connect RAP to RAP and maintain redundancy with connection to WLC.
I have one 1552 with the gigabit ethernet connected to the gigabit ethernet to another device that has a point-to-point link with another device where have a ethernet connection with a switch in the same broadcast domain where i have my WLC.
Next to this 1552 i have another 1552 that have the same situation, both with omnidirectional antenna.
I would like to have a Mesh connection with these two 1552 in 5Ghz, because if some point-to-point link is down i need redundancy to the WLC and my network, because i have some clients connected in the 2.4 Ghz in both Access Points.
Couple questions on setting channels on Cisco 1552s. First off almost all locations are fibered and set as RAPs. It doesn't allow me to set the channel assignment method to "global" to use DCA. It says it can't be done for a mesh backhaul AP. Is there any way around this? Next, when the channel is set to "custom" there are only 5 channels listed to choose from in the UNII-3 band. The spec sheet on the 1552 shows it supports other frequencies in the UNII-2 and UNII-2 extended range. Why can't I select those channels?
View 8 Replies View RelatedI want to set up AP 1552 as outdoor access point so serve clients. This AP is connected to 3750X switch and recieving power over ethernet.Now, by default AP 1552 come with bridge mode and it cannot be changed to local mode. I read on one of the post and made it ROOTAP but still the OPER STATUS is down. This device is already registered to my WLC.
what needs to be done to bring the AP in operational status.[code]
We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies View RelatedWe are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).
View 4 Replies View RelatedI know that a 1552 AP has 4 Ethernet ports. Is it possible to use them as some standard switch ports? If I connect two ore more devices to these ports do i have connectivity between them?
View 16 Replies View RelatedI am planning to provide a redudnt link to our customer. The setup as below:
One link over wireless while the other link over wired link, I want to make sure that I should maintain the same public IP addresses for the customer therefore, I am looking for L2 failover for my customer.
If the wireless down the customer should migrated to wired and vis versa. I have 7200 CISCO Router as Core.
I have Cisco WiSM running on 7.0.116.0 and 1522 Outdoor AP. I a trying to configure Mesh and I followed the Cisco deployment guide.I had added the MAC address of my AP in the Mac-filter list Configured the Root AP and Mesh AP.Configured the Mesh Parameter.Currently my issue is after removing the client from Ethernet its no more seen in the controller. There is also no information in the neighbour output.
View 2 Replies View RelatedI have seven autonomous AP1242AG (c1240-k9w7-tar.124-25d). Can I configure them to a mesh without WLC? [code]
View 2 Replies View Relateddoes cisco 2811 support?if no, can i make it work for BGP?also, i want to know the configuration of bGP for twoo ISPs for link failover.it will be google if u tell me step by step approach for configuring it
View 1 Replies View RelatedWe have a Cisco 1522AG configured as a MAP in our production network. Last week the AP went down. On investigating it keeps rebooting itself. constantly showing 4 orange leds, Maybe cant find the WLC? Is there a way to console into these devices to see whats happening in the background while its booting up or even reset it back to the factory defaults?
View 4 Replies View RelatedI have setup'd two 1142 AP's as mesh.The sceneario is like this:
MAP ------ RAP---------SW----------Router
I've done all the configuration through my WLC (Flex7500) and the mesh neighborship is up.The problem is not the MAP nor the RAP broadcasts my SSID.I've joined them to the same SSID and nothing.
A customer have a bad coverage in a corner of his branch office. He like to add a mesh AP (MAP) in the near of that corner.
I checked allready the documention about Mesh but i'm not sure if Flexconnect and Mesh works togheter. This MAP is in a branch office and the WLC is in the head quarter therefore he likes to uses Flexconnect togheter with Mesh.
I'm looking for documentation on the Enterprise mesh solution based on 7.0 MR1...In this release e.g 802.11n APs are supported and clean air for the client radio etc...The current Cisco Mesh Access Points, Design and Deployment Guide is based on the previous 7.0 release.Apart from the configuration guide I can't find any additional guides.
View 1 Replies View RelatedI have a Mesh architecture with 2112 WLC and 1042 APs I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.
View 4 Replies View Relatedhow to use Subinterfaces on an Etherchannel for a Lan Failover link?I successfully bundled e0/0-1 and e0/2-3 to 2 Port-Channels with a 3750X Stack - and was able to set my "nameifs" and "security level" on Port-Channel Subinterfaces like "Port-channel1.4" As a lan based failover link the subinterfaces seem to be unusable ....
View 1 Replies View RelatedI was trying to assing statefull link as same as LAN failover link on ASA5520 with VPN Plus license. But i am getting the below error. Is there any restriction in the license itself.
View 1 Replies View RelatedRV042 in Router mode.WAN1 preferred.With Smart Link it seems to work to a point.When WAN1 fails, it fails over to WAN2.But then it gets stuck on WAN2 and I have to manually switch to WAN2 preferred and then back to WAN1 preferred to get WAN1 connection to return.The test IP addresses should be just fine as set.
Is there something I should be doing differently?
I have one controller 5508 that will hold 50 LAP 1262 and another Controller that will hold another 50 outdoor mesh access point 1552. Both controllers (not redundant) are at the HQ while the access points are distributed between HQ and 3 branches.
The requirements is to have the SAME 4 SSIDs on MESH and LAP each have a security type (, wep,wpa,dot1x...) on HQ and Branches. Now, in the HQ I don't think I will face a problem since the WLCs is on the same LAN, so 5 interface v lans will be configured one for the WLCs and access point and another 4 interface v lans for the 4 SSIDs.
Now, for the remote sites I need to create another vlan on the switch with DHCP and option 43 ..... for the access point to register with the controller.
But here, do I have to create another 4 interface v lans (4 different sub nets) that should be bidden to the SSID as in the HQ?
Or the Access point will encapsulate all the traffic including the client traffic? Note that I have outdoor mesh access point and Lightweight access point and the BW link between the HQ and branch is 100M.
Also Can I have roaming between the same SSID that broadcasted on MESH and LAP knowing that each have different controller.
Done a wifi mesh using 1552E and 1552i mix of AP's ? With the 1552E as RAP and 1552I's as MAP's ? Is it a recommended model of deployment and will it work well ? the 1552i having radiation pattern more towards the ground when mounted on top , will the mesh backhaul to the 1552E be strong enough ?
Will this work if i put the 1552e at a lower level than the 1552i so that the mesh is formed properly ?
I would like to create a Mesh network using Cisco 1242 AP's running in Autonomous mode via A Channel.
View 5 Replies View Relatedif the Cisco 3502p AP can run as a root mesh access point ?
View 4 Replies View Related