Cisco Wireless :: LAP1142 Cannot Join WLC 2100
Apr 2, 2013
I'd WLC 2100 series and 9 access point LAP1142N .8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142 is can not . Part of LAP is AIR-LAP1142N-A-K9
Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr 2 10:52:42.284: status of voice_diag_test from WLC is false
*Apr 2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller
[code]....
View 4 Replies
ADVERTISEMENT
Apr 1, 2012
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies
View Related
Oct 1, 2012
I have a decent sized wireless network (120 1142 access points on a 5500 WLC) and any tips for maximizing the coverage. I know the only REAL way to fill true holes is to deploy more hardware, but I'm not sure if my WLC is configured properly to maximize the hardware already deployed. We have having a lot of issues with low signal in areas I feel are close enough to the AP that they should be good if not excellent signals. Our initial walkthrough and testing of the areas indicated that the APs we deployed SHOULD have been more than enough, but in real-world conditions it seems like it's not cutting the mustard.
View 5 Replies
View Related
Apr 4, 2013
I have a customer that has an air-lap1142. He says that it boot to Rommon, and he has to issue the boot command to get it to boot. What is the rommon command to have the ap boot to the image automatically?
View 1 Replies
View Related
Dec 21, 2011
I'm trying to remember what the command is to find the controller IP on a LAP1142 running 7.0.220.0 code.
View 2 Replies
View Related
Aug 27, 2012
We have some 1242 LAPs in a two 5508 controller setup working fine. All LAP are configured to obtain address from DHCP. After first join we usually change some configs like HOSTNAME, AP GROUP, PRIMARY AND SECONDARY WLC. After a software restart or a complete power off/power on the LAPs joins the primary controller and all configuration still there. We now add a 1142 LAP and is does not retain the configuration after a power off/power on cycle, but after a software restart there is no problem. The only way to retain the config is setting the AP with a static IP address.
We use WLC 7.0.116 and we see no errors in the LAP console.
View 1 Replies
View Related
Jul 18, 2012
I am trying to config my wireless lan controller (WLC) 2106 to discover my new 3500 access points.I followed the example Cisco configuration doc.69719.I am using a Cisco 3760 switch to interconnect the AP and WLC.I set up DHCP in the switch. [code]
View 6 Replies
View Related
Oct 10, 2010
Since few days the WLC 2100 series controller and 3x LAP1131AG are getting disconnected and the controller gets offline via the local ip address. At that point I have to reboot. To get anywhere and after I connect wirelessly to the AP before I know it it disconnects. It worked for 3 years straight no fuss. And now nothing. I reconfigured the WLC 10times and no diffference.
[code]....
View 6 Replies
View Related
Jan 3, 2013
We have two 2100 WLC's that support 12 access points. One has been sitting in a box for some time, but we're at the point where we need to add additional access points that will put us in excess of the 12 limitation. What is the best way to go for installing the second WLC?
View 2 Replies
View Related
Sep 1, 2011
I have a problem with our WLC 2100 series (2125). Basycally internal DHCP server configured on WLC is not working. I have one AP connected to port no 7 (PoE) to bypass and eliminate problem with other equipment.
Port no 7 details:
IP Address: 192.168.30.10
Netmask: 255.255.255.0
Default router: 192.168.30.1
DHCP Server: 192.168.1.250(code)
View 14 Replies
View Related
May 17, 2012
I have a fairly simple WLC 2100 configured to control two APs. We had a power outage a few days ago, and though the WLC was on a surge protector, it did not come back up properly after the outage. The STATUS light sticks at amber and I can't get any console response. At this point I'm not sure what to do except replace the WLC, though I'm loathed to do that as our budget was just cut substantially for next year and we're trying to turn nickels into pennies.
View 4 Replies
View Related
Feb 7, 2011
I am having trouble on setting up a WLC2100 ver 7. we need to implement a private and public network. private network authenticate to IAS - RADIUS (windows server 2003 server) while the public network is open but when a client connect to AP it will redirect to a 3rd party web athentication - HotSpot Server. the challenge is we want to broadcast a single SSID.
senario:
1. when a user/guest connect to the AP a radius server will authenticate thru IAS - Radius.
2. when a user is authenticate via radius a dhcp server will give an ip address of the private network.
3. if the user is not authenticate a dhcp server will give the public ip address and netowrk traffic must go to a different VLAN.
my question is, is it possible to broadcast a single SSID for the two network? is there a document which is related to our scenario?
View 2 Replies
View Related
Dec 17, 2009
The operating temperature for 2100 wireless lan controllers is up to a miximum of 40 degrees celsius according to the datasheet. We deployed some 2112 controllers all displaing a temperature above 50 degrees celsiun. This during normal operation and deployed proper enviromet (aroco ...)
View 2 Replies
View Related
Oct 10, 2012
How to switch on wireless on Compaq 2100
View 1 Replies
View Related
Aug 16, 2011
One of our customers have one Cisco WLC 2100 (firmware 5.2) with 4 AP Mesh 1522, in a city deployment. In order to achieve local regulatory, has to implement bandwidth limitations per user.
I got screen captures of WLC QoS Profiles options, with Average Data Rate in Per-User Bandwidth Contracts. So my question is, do I need any other equipment to achieve per user bandwidth limitation? Can it be done with WLC QoS options?
View 3 Replies
View Related
Apr 30, 2012
We have a 2100 cisco Wireless LAN Controller which manages 3 APs and assign IP address to clients which connects via wifi. Currently, we are deploying dual stack IPv6 and our consultant stated that our current controller does not support IPv6.
This is rather odd statement because there is an option to enable IPv6 in the advance tab of WLAN. And sometimes clients (win7 and Mac OS X) are getting v6 addresses, able to ping v6 sites, and reach v6 sites successfully. And other times, clients do not..or getting the v6 address for 10-15minutes, then unable to ping/reach v6 sites.
Our consultant is sticking by his words saying it does not support. If this is true, then clients should not be able to get v6 at all....not sometimes and not other times; very inconsistent.
And what is ipv6 pass through? What is ipv6 bridging?
View 2 Replies
View Related
Feb 27, 2013
I have a couple of AP's that are down and won't let me change to up. When I try to enable admin status I get a pop up window: " error in enabling admin status".
I have configured the WLC for power injectors with a 3550.
View 2 Replies
View Related
Jul 29, 2012
I have a wireless controller 2100. I can't access it via browser, when I am connected to one of its physical ports. I use the same subnet ip address as that of the management interface of the wlc.
View 5 Replies
View Related
Jan 29, 2013
In the near future my company is looking into the option of adding a second network connection (exclusively for customers visiting our facility) to our pre existing WLAN network. We are currently using a Cisco 2100 series Wireless LAN Controller and probably 6-8 APs. Our main connection is made up of 4 T1 lines and the second connection will more than likely be a cheap DSL connection. I'm wondering if this technology supports two separate connections on one controller and APs. For example, is there a way within the controller web interface to separate what is currently our "Guest" connection from the main Internet line? I was thinking of just plugging from the DSL router directly to the controller and save the hassle of changing routing and VLANs.
View 12 Replies
View Related
Apr 2, 2011
I have a D Link WL-2100 AP, I connected my PC to AP with ethernet cable, then I tried to connect the AP to my wireless modem but I couldn't do.How can I make the AP recognize wireless modem?
View 2 Replies
View Related
May 5, 2012
Can I upgrade or add WPA to WEP on Intel(R) PRO/Wireless Lan 2100 3B Mini PCI Adapter
View 1 Replies
View Related
Oct 4, 2011
We have 4 1142N LAPs that I want to divide between an internal wireless and a guest wireless network using the controller. Currently all of the APs are on an established internal network, but I want to migrate one over to a test guest network before buying more LAPs to augment the networks further. Currently the port connecting to the WCS from the 3560 switch is configured as an access port using VLAN 10. Whenever I make it a trunk port carrying VLAN 10 as well as the other ports we will be using for the guest and ap-manager networks, I lose connection with the controller. To me this implies that the port on the controller is configured as an access port as well. In the documentation I found for the controller it states that by default the ports are al configured to be trunks, but it appears as though something was changed by the previous tech. All of the APs are connected to other switches, not to the controller itself.
1) How can I get the port on the controller back to being a trunk port
2) Can I use the internal DHCP server for the guest network if the subnet is different than the management subnet, or will I have to use another external server and relay/proxy it through the controller to give guest clients IP addresses?
View 2 Replies
View Related
Feb 24, 2013
I have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies
View Related
Apr 28, 2011
Dell 8600 centrino intel pro wireless lan 2100 won't connect to netgear n150 wnr1000. Running 802.11b band it sees wireless network but won't connect. I have 2 other computers connected to network so it works.... I don't know if Netgear n150 is compatible with 802.11b band...
View 1 Replies
View Related
Feb 13, 2011
I'm trying to re-setup this EOL camera on a new router.I've been able to reset the cam to factory defaults and see it wired using dhcp. I then was able to change the address to a static address, still wired and still can see it with IE. However when I disconnect the rj-45 cable, power down and restart, I can't access the cam.
View 2 Replies
View Related
Jan 17, 2011
i have a cisco ACS version 5.0, I need to authenticate a wireless users connected to WLC 2100 controller when i connect the controller to a Dot1x port in the switch , the port go down.
View 6 Replies
View Related
May 16, 2013
I am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.
WLC: Cisco 2500
IP Address: 192.168.1.225
version: 7.4.100.0
View 5 Replies
View Related
Mar 24, 2013
Our offcie use WLC2100 Series controller with AIR-LAP1031 and successfully join and running. Now i am trying to replace one ap with AIR-LAP1041N and join with WLC, but i can't and below the error message generate:
[code]....
View 2 Replies
View Related
Jul 10, 2012
I am trying to set up a Wireless network a WLC hosted on an SRE module in a 2911 router. I think i have most of my bases covered but there is still one problem.
My LAP1131AG AP's won't join the controller, on the AP im am seeing this:
Translating "CISCO-LWAPP-CONTROLLER.test.local"...domain server (192.168.250.10) [OK]
[Code].....
But to my knowledge an LWAP AP schould be able to join a CAPWAP WLC
View 2 Replies
View Related
Apr 8, 2012
WLC software 7.2.103.0
1. first problem: AP1252 can´t join on WLC. MAC was add on mac filter properly.
170Mon Apr 9 15:37:32 2012Mesh Node '2c:3f:38:be:53:ef' failed to join controller, MAC address not in MAC filter list.171Mon Apr 9 15:37:32 2012AAA Authentication Failure for UserName:2c3f38be53e0 User Type: WLAN USER172Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 40:a6:d9:ef:87:68 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 46 7 5 4 2 1 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0173Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 8c:7b:9d:05:a0:67 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 50 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0174Mon Apr 9 15:37:30
[code]....
Several APs can´t join on WLC and all are added on MAC filter, but they are showing this messages.
2 . Second problem.: Operational Status = UNKNOWN
Some Access Point are in UNKNOWN status. I tried but I can´t do the reboot. I can access Web config the APs using WLC, but when I applied the reset, it wasn´t working properly.
View 2 Replies
View Related
Jun 10, 2013
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
View 15 Replies
View Related
Jan 31, 2013
I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.
View 19 Replies
View Related
Jun 29, 2011
My WLC running 6.0.182.0 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).
I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!
View 4 Replies
View Related
