One of our customers have one Cisco WLC 2100 (firmware 5.2) with 4 AP Mesh 1522, in a city deployment. In order to achieve local regulatory, has to implement bandwidth limitations per user.
I got screen captures of WLC QoS Profiles options, with Average Data Rate in Per-User Bandwidth Contracts. So my question is, do I need any other equipment to achieve per user bandwidth limitation? Can it be done with WLC QoS options?
does the cisco wlc 2504 (software release 7.4) support QoS per-user bandwidth contracts ? I only can see the default QoS profiles (gold, platinum...) i can't see the per-user bandwidth contract to modify it. shoud it be activated ?
View 3 Replies View RelatedI have an instance of ISE and NCS with a WLC 2100 plus a couple of LWAPs. This is an evaluation POC lab to sell ISE and NCS to our management to make our life easier.The problem I have amoungst many is I can create a guest user directly on the ISE and the guest can login, the ISE monitor shows the guest authenticates but the clients webpage passes them back to the login page not onto the original client url. The web auth is pointed at the ISE/guestportal/portal.jsp page.If I point the web auth at the internal WLC page using a WLC local user account it works.If I set the guest access to pass through it works without issues getting dhcp and dns. On the ISE is there a policy needed to say if guests are web authenticated give them access? The need is for AD authenticated users to be able tocreate guest users. The AD authentication works for sponsorship and guest creation its just the guest access redirection I am having issues with.
View 1 Replies View RelatedI have a 20/20 MB circuit and an ASA 5510 and I am able to setup policing were the interace gets 512k down and 128k up so when I conduct a speed test with one user I get 512k and 128k and when I conduct a speed test with two users each gets 256k and 64k. [code] What I want to happen is that each user gets 512k and 128k until a saturation point is hit and then I want the ASA to slow all users down equally.
View 1 Replies View Relatedhow to limit bandwidth only for user account in window 7...My PC has 2 account ..one is admin and other is user ..i need to limit the bandwidth only for user account ,do I need a software for this.
View 3 Replies View RelatedThe rest of us use wifi for our internet services but this isn't good enough for are newest member so they have now connected a cable directly into the modem, so now whenever he is online ALL wifi suffers dramatically! What can i do to limit his bandwidth and allow the wifi to gain more access is there a way to limit via his MAC address or IP address?
View 3 Replies View RelatedI need to find a free software to find who is the heaviest bandwidth user on my LAN.The problem is that some of the users on LAN keep downloading/uploading all the time & i couldn't get to view any web-pages?
View 2 Replies View RelatedI currently have 2 5505 SEC BUN as Primary/FO Firewalls and I am considering purchasing the ASA5510-AIP10-K9 for use as a dedicated IPS device. Looking at [URL] I see that for service updates, CON-SU1-AS1A10K9 is available for this product, providing "IPS Signature and Engine Updates" and "OS Updates."It is my understanding that in the ASA5510-AIP10-K9 there are 2 OS:
1. ASA OS
2. AIP SSM-10 OS
My question is: Are both the ASA and AIP SSM-10 able to receive "OS updates" with this service contract?
how can I configure a Catalyst 3750, which interface is patched on the ISP router (internet uplink bandwidth = 20Mbps with) to allow all active users are sharing the bandwidth (either 5, 50, 100, user simultaneously..in internet surfing. right now it's like when a user starts a larger download that it uses the bulk of the bandwidth, and other users can reach all remaining extremely slow access times.
View 3 Replies View RelatedI have a cisco 2950 switch, connected with 4Mbps of internet and number of users will access the internet. There is no restraction on bandwidth limit for users, if any body use high download the remaining users are facing the slow browsing problems.
So, if i can put a bandwidth limitation for every users the problem will be solved. how to restract the bandwidth on user bases.
configuring a switch or a router to limit the bandwidth for a specific user/IP when need it. Most of my remote offices are configured like this:
Users ------ 3560 switch ------- 2801 router -------- T1 to NOC -------- 7204 router with channelized DS3
I use Netflow Analyzer for high bandwidth usage alerts and can see the user's IP right away when someone is clogging our T1s. My goal is to be able to temporarily limit the bandwidth of the user taking over the T1. Whatever is best switch config or on the router.
I am trying to config my wireless lan controller (WLC) 2106 to discover my new 3500 access points.I followed the example Cisco configuration doc.69719.I am using a Cisco 3760 switch to interconnect the AP and WLC.I set up DHCP in the switch. [code]
View 6 Replies View RelatedSince few days the WLC 2100 series controller and 3x LAP1131AG are getting disconnected and the controller gets offline via the local ip address. At that point I have to reboot. To get anywhere and after I connect wirelessly to the AP before I know it it disconnects. It worked for 3 years straight no fuss. And now nothing. I reconfigured the WLC 10times and no diffference.
[code]....
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies View RelatedI'd WLC 2100 series and 9 access point LAP1142N .8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142 is can not . Part of LAP is AIR-LAP1142N-A-K9
Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr 2 10:52:42.284: status of voice_diag_test from WLC is false
*Apr 2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller
[code]....
We have two 2100 WLC's that support 12 access points. One has been sitting in a box for some time, but we're at the point where we need to add additional access points that will put us in excess of the 12 limitation. What is the best way to go for installing the second WLC?
View 2 Replies View RelatedI have a problem with our WLC 2100 series (2125). Basycally internal DHCP server configured on WLC is not working. I have one AP connected to port no 7 (PoE) to bypass and eliminate problem with other equipment.
Port no 7 details:
IP Address: 192.168.30.10
Netmask: 255.255.255.0
Default router: 192.168.30.1
DHCP Server: 192.168.1.250(code)
I have a fairly simple WLC 2100 configured to control two APs. We had a power outage a few days ago, and though the WLC was on a surge protector, it did not come back up properly after the outage. The STATUS light sticks at amber and I can't get any console response. At this point I'm not sure what to do except replace the WLC, though I'm loathed to do that as our budget was just cut substantially for next year and we're trying to turn nickels into pennies.
View 4 Replies View RelatedI am having trouble on setting up a WLC2100 ver 7. we need to implement a private and public network. private network authenticate to IAS - RADIUS (windows server 2003 server) while the public network is open but when a client connect to AP it will redirect to a 3rd party web athentication - HotSpot Server. the challenge is we want to broadcast a single SSID.
senario:
1. when a user/guest connect to the AP a radius server will authenticate thru IAS - Radius.
2. when a user is authenticate via radius a dhcp server will give an ip address of the private network.
3. if the user is not authenticate a dhcp server will give the public ip address and netowrk traffic must go to a different VLAN.
my question is, is it possible to broadcast a single SSID for the two network? is there a document which is related to our scenario?
The operating temperature for 2100 wireless lan controllers is up to a miximum of 40 degrees celsius according to the datasheet. We deployed some 2112 controllers all displaing a temperature above 50 degrees celsiun. This during normal operation and deployed proper enviromet (aroco ...)
View 2 Replies View RelatedHow to switch on wireless on Compaq 2100
View 1 Replies View RelatedWe have a 2100 cisco Wireless LAN Controller which manages 3 APs and assign IP address to clients which connects via wifi. Currently, we are deploying dual stack IPv6 and our consultant stated that our current controller does not support IPv6.
This is rather odd statement because there is an option to enable IPv6 in the advance tab of WLAN. And sometimes clients (win7 and Mac OS X) are getting v6 addresses, able to ping v6 sites, and reach v6 sites successfully. And other times, clients do not..or getting the v6 address for 10-15minutes, then unable to ping/reach v6 sites.
Our consultant is sticking by his words saying it does not support. If this is true, then clients should not be able to get v6 at all....not sometimes and not other times; very inconsistent.
And what is ipv6 pass through? What is ipv6 bridging?
I have a couple of AP's that are down and won't let me change to up. When I try to enable admin status I get a pop up window: " error in enabling admin status".
I have configured the WLC for power injectors with a 3550.
I have a wireless controller 2100. I can't access it via browser, when I am connected to one of its physical ports. I use the same subnet ip address as that of the management interface of the wlc.
View 5 Replies View RelatedIn the near future my company is looking into the option of adding a second network connection (exclusively for customers visiting our facility) to our pre existing WLAN network. We are currently using a Cisco 2100 series Wireless LAN Controller and probably 6-8 APs. Our main connection is made up of 4 T1 lines and the second connection will more than likely be a cheap DSL connection. I'm wondering if this technology supports two separate connections on one controller and APs. For example, is there a way within the controller web interface to separate what is currently our "Guest" connection from the main Internet line? I was thinking of just plugging from the DSL router directly to the controller and save the hassle of changing routing and VLANs.
View 12 Replies View RelatedIs it configurable to allow wifi user to user traffic on WLC 5508?
View 4 Replies View RelatedI have a D Link WL-2100 AP, I connected my PC to AP with ethernet cable, then I tried to connect the AP to my wireless modem but I couldn't do.How can I make the AP recognize wireless modem?
View 2 Replies View RelatedCan I upgrade or add WPA to WEP on Intel(R) PRO/Wireless Lan 2100 3B Mini PCI Adapter
View 1 Replies View RelatedWe have 4 1142N LAPs that I want to divide between an internal wireless and a guest wireless network using the controller. Currently all of the APs are on an established internal network, but I want to migrate one over to a test guest network before buying more LAPs to augment the networks further. Currently the port connecting to the WCS from the 3560 switch is configured as an access port using VLAN 10. Whenever I make it a trunk port carrying VLAN 10 as well as the other ports we will be using for the guest and ap-manager networks, I lose connection with the controller. To me this implies that the port on the controller is configured as an access port as well. In the documentation I found for the controller it states that by default the ports are al configured to be trunks, but it appears as though something was changed by the previous tech. All of the APs are connected to other switches, not to the controller itself.
1) How can I get the port on the controller back to being a trunk port
2) Can I use the internal DHCP server for the guest network if the subnet is different than the management subnet, or will I have to use another external server and relay/proxy it through the controller to give guest clients IP addresses?
I have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies View RelatedDell 8600 centrino intel pro wireless lan 2100 won't connect to netgear n150 wnr1000. Running 802.11b band it sees wireless network but won't connect. I have 2 other computers connected to network so it works.... I don't know if Netgear n150 is compatible with 802.11b band...
View 1 Replies View RelatedI'm trying to re-setup this EOL camera on a new router.I've been able to reset the cam to factory defaults and see it wired using dhcp. I then was able to change the address to a static address, still wired and still can see it with IE. However when I disconnect the rj-45 cable, power down and restart, I can't access the cam.
View 2 Replies View Relatedi have a cisco ACS version 5.0, I need to authenticate a wireless users connected to WLC 2100 controller when i connect the controller to a Dot1x port in the switch , the port go down.
View 6 Replies View Related
