Cisco Wireless :: WLC 2100 Ipv6 Ready Connection
Apr 30, 2012
We have a 2100 cisco Wireless LAN Controller which manages 3 APs and assign IP address to clients which connects via wifi. Currently, we are deploying dual stack IPv6 and our consultant stated that our current controller does not support IPv6.
This is rather odd statement because there is an option to enable IPv6 in the advance tab of WLAN. And sometimes clients (win7 and Mac OS X) are getting v6 addresses, able to ping v6 sites, and reach v6 sites successfully. And other times, clients do not..or getting the v6 address for 10-15minutes, then unable to ping/reach v6 sites.
Our consultant is sticking by his words saying it does not support. If this is true, then clients should not be able to get v6 at all....not sometimes and not other times; very inconsistent.
And what is ipv6 pass through? What is ipv6 bridging?
View 2 Replies
ADVERTISEMENT
Mar 13, 2013
I have a Killer Nic 2100 installed on an 1155 setup under Windows 8. I can upload large files to anywhere on my home network .. but when I pull large files off of my main computer with the Killer Nic in it .. the connection drops out on my main rig... no network connection of any kind on my main rig until I reboot ..
I don't have this problem with the onboard nic ..
sometimes the network will drop when the power flutters .. all the other computers I have will have internet connection .. but my rig won't ..
View 15 Replies
View Related
Aug 30, 2012
My ISP (OTEnet, Greece) offers IPv6 connectivity in the form of dual-stack IPv4/IPv6 with the requirement that the router supports DHCPv6 Prefix Delegation for establishing an IPv6 connection.Using other routers (Cisco 887W, DrayTek Vigor2130n), I have established an IPv4/IPv6 connection but I am unable to do so with the EA4500. As a matter of fact, when I have the "IPv6 - Automatic" option enabled the router not only cannot obtain an IPv6 prefix from the ISP but it gets stuck in the connection attempt and never obtains an IPv4 or an IPv6 address. I have to disable the IPv6 option in order to simply establish an IPv4-only connection without problems.So, my questions are:
1. Does the latest (2.1.38.38880) firmware support dual-stack IPv6 and DHCPv6 Prefix Delegation?
2. If the router cannot negotiate an IPv6 connection why is it not establishing an IPv4 connection only but gets stuck in the process?
View 9 Replies
View Related
Jan 1, 2013
can I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies
View Related
Jun 26, 2011
I'm trying to connect to a wireless network provided by a Sprint mobile hotspot. My computer is running XP SP3 and using a wireless USB adapter to do it. (802.1n)I can detect the network but when I try to connect using Windows I get the message "Windows waiting for the network to be ready." And apparently the network is never ready.I can also use the software that come with the adapter. That doesn't work because when I put in the password for WPA 2, the program saves a password that is far longer then the one I entered. Then I get the message "Authentication failed!" Well, duh.Then the computer tries to connect over and over with no results. "Trying to connect ... disconnected ... etc."
View 13 Replies
View Related
Apr 26, 2011
setup ready share on my WNDR3700? when i log into the router it sees and recognizes my hard drive but it wont let me create a network folder all the buttons are grayed out
View 8 Replies
View Related
Mar 4, 2011
Here are the configs for failover:
PRIMARY
failover lan unit primary
failover lan interface failover GigabitEthernet0/3
failover interface ip failover 192.168.3.1 255.255.255.0 standby 192.168.3.2
failover link failover GigabitEthernet0/3
failover
SECONDARY
failover lan interface failover GigabitEthernet0/3
failover interface ip failover 192.168.3.1 255.255.255.0 standby 192.168.3.2
failover lan unit secondary
failover
In the above configs is it i m missing something for failover? when i shut the INSIDE interface of Secondary ASA I get the below output, It shows me secondary failed and primary Active, WHY it is showing me FAILED instead of STANDBY/READY. What i know about firewall failover is when active goes down the other becomes standby unit but in this scenario it is showing me FAILED,
FW0001(config)# sh failover
Failover On
Failover unit Secondary
[Code] ....
View 8 Replies
View Related
Mar 22, 2012
I want change my old router to new one. I have problem with runing SERVICES READY PLATFORM WIZARD.
View 1 Replies
View Related
Dec 19, 2012
we have configured VpC between two Nexus 5596, for Vpc-Keep-alive-link we configured L3 interface with 1G (GLC-T) ,it shows the below status message "L3 not Ready" with interface LED glows in Yellow in color. is this a physical layer problem
Ethernet VLAN Type Mode Status Reason Speed Po Ch
Eth1/17 -- eth routed down L3 not ready 1000(D) --
Eth1/18 1 eth access down SFP not inserted 10G(D) --
Eth1/19 1 eth access down SFP not inserted 10G(D) --
Eth1/20 1 eth access down SFP not inserted 10G(D) --
Eth1/21 1 eth access down SFP not inserted 10G(D) --
[code].....
View 10 Replies
View Related
Jan 25, 2012
My ISP provides IPv6 connectivity in the form of dual stack IPv4/IPv6 with DHCPv6 Prefix Delegation. Using a Cisco IOS-based router I managed to make such a connection by using as a template the Cisco IOS configuration file that my ISP has posted as an example in the following link:
[URL]
The main point on this configuration is a PPPoE connection with:
interface Dialer46
ipv6 address autoconfig default
ipv6 enable
[Code].....
configure this router according the Cisco IOS configuration file I linked on the top in order to have a working IPv6 connection?
View 4 Replies
View Related
Aug 10, 2011
I have a dell inspiron 15 and I've been having trouble fully connecting to my wireless internet. It says I have signal but gets stuck on identifying the network and I have limited IPv4 and IPv6 connectivity.
Here's the ipconfig if you can identify the issue with it:
Windows IP Configuration
Host Name . . . . . . . . . . . . : M-PC
Primary Dns Suffix . . . . . . . :
[Code].....
View 11 Replies
View Related
Jul 19, 2012
We have some technical issue with IPv6 router configuration[DLINK 655] when we try to connect it with ISP provided static IPv6 connection.
[Code]...
View 9 Replies
View Related
Oct 14, 2011
I have a d link dir 615 "ipv6 ready". My internet provider give tome a native ipv6 /48. I configure the router with my ipv6 /48 address the internal propagation of the address is good.
On the status ipv6 page all seems OK marked "connected" but I can't have an ipv6real connection and my provider say to me that i am not connected.
Is there a known problem of connection between an public /48 and the internal /64 and if so could it be corrected.
View 12 Replies
View Related
Jul 18, 2012
I am trying to config my wireless lan controller (WLC) 2106 to discover my new 3500 access points.I followed the example Cisco configuration doc.69719.I am using a Cisco 3760 switch to interconnect the AP and WLC.I set up DHCP in the switch. [code]
View 6 Replies
View Related
Oct 10, 2010
Since few days the WLC 2100 series controller and 3x LAP1131AG are getting disconnected and the controller gets offline via the local ip address. At that point I have to reboot. To get anywhere and after I connect wirelessly to the AP before I know it it disconnects. It worked for 3 years straight no fuss. And now nothing. I reconfigured the WLC 10times and no diffference.
[code]....
View 6 Replies
View Related
Apr 1, 2012
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies
View Related
Apr 2, 2013
I'd WLC 2100 series and 9 access point LAP1142N .8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142 is can not . Part of LAP is AIR-LAP1142N-A-K9
Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr 2 10:52:42.284: status of voice_diag_test from WLC is false
*Apr 2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller
[code]....
View 4 Replies
View Related
Jan 3, 2013
We have two 2100 WLC's that support 12 access points. One has been sitting in a box for some time, but we're at the point where we need to add additional access points that will put us in excess of the 12 limitation. What is the best way to go for installing the second WLC?
View 2 Replies
View Related
Sep 1, 2011
I have a problem with our WLC 2100 series (2125). Basycally internal DHCP server configured on WLC is not working. I have one AP connected to port no 7 (PoE) to bypass and eliminate problem with other equipment.
Port no 7 details:
IP Address: 192.168.30.10
Netmask: 255.255.255.0
Default router: 192.168.30.1
DHCP Server: 192.168.1.250(code)
View 14 Replies
View Related
May 17, 2012
I have a fairly simple WLC 2100 configured to control two APs. We had a power outage a few days ago, and though the WLC was on a surge protector, it did not come back up properly after the outage. The STATUS light sticks at amber and I can't get any console response. At this point I'm not sure what to do except replace the WLC, though I'm loathed to do that as our budget was just cut substantially for next year and we're trying to turn nickels into pennies.
View 4 Replies
View Related
Feb 7, 2011
I am having trouble on setting up a WLC2100 ver 7. we need to implement a private and public network. private network authenticate to IAS - RADIUS (windows server 2003 server) while the public network is open but when a client connect to AP it will redirect to a 3rd party web athentication - HotSpot Server. the challenge is we want to broadcast a single SSID.
senario:
1. when a user/guest connect to the AP a radius server will authenticate thru IAS - Radius.
2. when a user is authenticate via radius a dhcp server will give an ip address of the private network.
3. if the user is not authenticate a dhcp server will give the public ip address and netowrk traffic must go to a different VLAN.
my question is, is it possible to broadcast a single SSID for the two network? is there a document which is related to our scenario?
View 2 Replies
View Related
Dec 17, 2009
The operating temperature for 2100 wireless lan controllers is up to a miximum of 40 degrees celsius according to the datasheet. We deployed some 2112 controllers all displaing a temperature above 50 degrees celsiun. This during normal operation and deployed proper enviromet (aroco ...)
View 2 Replies
View Related
Oct 10, 2012
How to switch on wireless on Compaq 2100
View 1 Replies
View Related
Aug 16, 2011
One of our customers have one Cisco WLC 2100 (firmware 5.2) with 4 AP Mesh 1522, in a city deployment. In order to achieve local regulatory, has to implement bandwidth limitations per user.
I got screen captures of WLC QoS Profiles options, with Average Data Rate in Per-User Bandwidth Contracts. So my question is, do I need any other equipment to achieve per user bandwidth limitation? Can it be done with WLC QoS options?
View 3 Replies
View Related
Feb 27, 2013
I have a couple of AP's that are down and won't let me change to up. When I try to enable admin status I get a pop up window: " error in enabling admin status".
I have configured the WLC for power injectors with a 3550.
View 2 Replies
View Related
Jul 29, 2012
I have a wireless controller 2100. I can't access it via browser, when I am connected to one of its physical ports. I use the same subnet ip address as that of the management interface of the wlc.
View 5 Replies
View Related
Jan 29, 2013
In the near future my company is looking into the option of adding a second network connection (exclusively for customers visiting our facility) to our pre existing WLAN network. We are currently using a Cisco 2100 series Wireless LAN Controller and probably 6-8 APs. Our main connection is made up of 4 T1 lines and the second connection will more than likely be a cheap DSL connection. I'm wondering if this technology supports two separate connections on one controller and APs. For example, is there a way within the controller web interface to separate what is currently our "Guest" connection from the main Internet line? I was thinking of just plugging from the DSL router directly to the controller and save the hassle of changing routing and VLANs.
View 12 Replies
View Related
Apr 2, 2011
I have a D Link WL-2100 AP, I connected my PC to AP with ethernet cable, then I tried to connect the AP to my wireless modem but I couldn't do.How can I make the AP recognize wireless modem?
View 2 Replies
View Related
May 5, 2012
Can I upgrade or add WPA to WEP on Intel(R) PRO/Wireless Lan 2100 3B Mini PCI Adapter
View 1 Replies
View Related
Oct 4, 2011
We have 4 1142N LAPs that I want to divide between an internal wireless and a guest wireless network using the controller. Currently all of the APs are on an established internal network, but I want to migrate one over to a test guest network before buying more LAPs to augment the networks further. Currently the port connecting to the WCS from the 3560 switch is configured as an access port using VLAN 10. Whenever I make it a trunk port carrying VLAN 10 as well as the other ports we will be using for the guest and ap-manager networks, I lose connection with the controller. To me this implies that the port on the controller is configured as an access port as well. In the documentation I found for the controller it states that by default the ports are al configured to be trunks, but it appears as though something was changed by the previous tech. All of the APs are connected to other switches, not to the controller itself.
1) How can I get the port on the controller back to being a trunk port
2) Can I use the internal DHCP server for the guest network if the subnet is different than the management subnet, or will I have to use another external server and relay/proxy it through the controller to give guest clients IP addresses?
View 2 Replies
View Related
Feb 24, 2013
I have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies
View Related
Apr 28, 2011
Dell 8600 centrino intel pro wireless lan 2100 won't connect to netgear n150 wnr1000. Running 802.11b band it sees wireless network but won't connect. I have 2 other computers connected to network so it works.... I don't know if Netgear n150 is compatible with 802.11b band...
View 1 Replies
View Related
Feb 13, 2011
I'm trying to re-setup this EOL camera on a new router.I've been able to reset the cam to factory defaults and see it wired using dhcp. I then was able to change the address to a static address, still wired and still can see it with IE. However when I disconnect the rj-45 cable, power down and restart, I can't access the cam.
View 2 Replies
View Related
