The operating temperature for 2100 wireless lan controllers is up to a miximum of 40 degrees celsius according to the datasheet. We deployed some 2112 controllers all displaing a temperature above 50 degrees celsiun. This during normal operation and deployed proper enviromet (aroco ...)
View 2 RepliesI have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies View RelatedI cant remember where I read it but when I noticed that my HDD was running hot even when it was meant to be idle, I read that the router causes the storage device to run at full spin regardless.
I was wondering, do we know if that issue is fixed with this latest firmware update (June 14th)? I've had it on for about 10minutes but I'm not sure how long it takes to get to the temp that it was running at before.
Recently i have visit some site for survey of wireless (WiFi). My client ask to provide the Access Point inside the Cold storage of factory( For RF scanners) The temperature of the place is -25 C to -30 C. I have go throug the wireless option of cisco like 1200 series, 1100 series, 3500 series, but all of these operate maximum of -20C. while only out door access point ( cisco 1500 Series ) support such low temparture.
View 13 Replies View RelatedYesterday I installed my new E3000 router. After an hour I noticed that de temperature of the bottom was very high and it stil is . Is that normal?
View 7 Replies View RelatedI am trying to config my wireless lan controller (WLC) 2106 to discover my new 3500 access points.I followed the example Cisco configuration doc.69719.I am using a Cisco 3760 switch to interconnect the AP and WLC.I set up DHCP in the switch. [code]
View 6 Replies View RelatedSince few days the WLC 2100 series controller and 3x LAP1131AG are getting disconnected and the controller gets offline via the local ip address. At that point I have to reboot. To get anywhere and after I connect wirelessly to the AP before I know it it disconnects. It worked for 3 years straight no fuss. And now nothing. I reconfigured the WLC 10times and no diffference.
[code]....
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies View RelatedI'd WLC 2100 series and 9 access point LAP1142N .8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142 is can not . Part of LAP is AIR-LAP1142N-A-K9
Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr 2 10:52:42.284: status of voice_diag_test from WLC is false
*Apr 2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller
[code]....
We have two 2100 WLC's that support 12 access points. One has been sitting in a box for some time, but we're at the point where we need to add additional access points that will put us in excess of the 12 limitation. What is the best way to go for installing the second WLC?
View 2 Replies View RelatedI have a problem with our WLC 2100 series (2125). Basycally internal DHCP server configured on WLC is not working. I have one AP connected to port no 7 (PoE) to bypass and eliminate problem with other equipment.
Port no 7 details:
IP Address: 192.168.30.10
Netmask: 255.255.255.0
Default router: 192.168.30.1
DHCP Server: 192.168.1.250(code)
I have a fairly simple WLC 2100 configured to control two APs. We had a power outage a few days ago, and though the WLC was on a surge protector, it did not come back up properly after the outage. The STATUS light sticks at amber and I can't get any console response. At this point I'm not sure what to do except replace the WLC, though I'm loathed to do that as our budget was just cut substantially for next year and we're trying to turn nickels into pennies.
View 4 Replies View RelatedI am having trouble on setting up a WLC2100 ver 7. we need to implement a private and public network. private network authenticate to IAS - RADIUS (windows server 2003 server) while the public network is open but when a client connect to AP it will redirect to a 3rd party web athentication - HotSpot Server. the challenge is we want to broadcast a single SSID.
senario:
1. when a user/guest connect to the AP a radius server will authenticate thru IAS - Radius.
2. when a user is authenticate via radius a dhcp server will give an ip address of the private network.
3. if the user is not authenticate a dhcp server will give the public ip address and netowrk traffic must go to a different VLAN.
my question is, is it possible to broadcast a single SSID for the two network? is there a document which is related to our scenario?
How to switch on wireless on Compaq 2100
View 1 Replies View RelatedOne of our customers have one Cisco WLC 2100 (firmware 5.2) with 4 AP Mesh 1522, in a city deployment. In order to achieve local regulatory, has to implement bandwidth limitations per user.
I got screen captures of WLC QoS Profiles options, with Average Data Rate in Per-User Bandwidth Contracts. So my question is, do I need any other equipment to achieve per user bandwidth limitation? Can it be done with WLC QoS options?
We have a 2100 cisco Wireless LAN Controller which manages 3 APs and assign IP address to clients which connects via wifi. Currently, we are deploying dual stack IPv6 and our consultant stated that our current controller does not support IPv6.
This is rather odd statement because there is an option to enable IPv6 in the advance tab of WLAN. And sometimes clients (win7 and Mac OS X) are getting v6 addresses, able to ping v6 sites, and reach v6 sites successfully. And other times, clients do not..or getting the v6 address for 10-15minutes, then unable to ping/reach v6 sites.
Our consultant is sticking by his words saying it does not support. If this is true, then clients should not be able to get v6 at all....not sometimes and not other times; very inconsistent.
And what is ipv6 pass through? What is ipv6 bridging?
I have a couple of AP's that are down and won't let me change to up. When I try to enable admin status I get a pop up window: " error in enabling admin status".
I have configured the WLC for power injectors with a 3550.
I have a wireless controller 2100. I can't access it via browser, when I am connected to one of its physical ports. I use the same subnet ip address as that of the management interface of the wlc.
View 5 Replies View RelatedIn the near future my company is looking into the option of adding a second network connection (exclusively for customers visiting our facility) to our pre existing WLAN network. We are currently using a Cisco 2100 series Wireless LAN Controller and probably 6-8 APs. Our main connection is made up of 4 T1 lines and the second connection will more than likely be a cheap DSL connection. I'm wondering if this technology supports two separate connections on one controller and APs. For example, is there a way within the controller web interface to separate what is currently our "Guest" connection from the main Internet line? I was thinking of just plugging from the DSL router directly to the controller and save the hassle of changing routing and VLANs.
View 12 Replies View RelatedI have a D Link WL-2100 AP, I connected my PC to AP with ethernet cable, then I tried to connect the AP to my wireless modem but I couldn't do.How can I make the AP recognize wireless modem?
View 2 Replies View RelatedCan I upgrade or add WPA to WEP on Intel(R) PRO/Wireless Lan 2100 3B Mini PCI Adapter
View 1 Replies View RelatedWe have 4 1142N LAPs that I want to divide between an internal wireless and a guest wireless network using the controller. Currently all of the APs are on an established internal network, but I want to migrate one over to a test guest network before buying more LAPs to augment the networks further. Currently the port connecting to the WCS from the 3560 switch is configured as an access port using VLAN 10. Whenever I make it a trunk port carrying VLAN 10 as well as the other ports we will be using for the guest and ap-manager networks, I lose connection with the controller. To me this implies that the port on the controller is configured as an access port as well. In the documentation I found for the controller it states that by default the ports are al configured to be trunks, but it appears as though something was changed by the previous tech. All of the APs are connected to other switches, not to the controller itself.
1) How can I get the port on the controller back to being a trunk port
2) Can I use the internal DHCP server for the guest network if the subnet is different than the management subnet, or will I have to use another external server and relay/proxy it through the controller to give guest clients IP addresses?
Dell 8600 centrino intel pro wireless lan 2100 won't connect to netgear n150 wnr1000. Running 802.11b band it sees wireless network but won't connect. I have 2 other computers connected to network so it works.... I don't know if Netgear n150 is compatible with 802.11b band...
View 1 Replies View RelatedI'm trying to re-setup this EOL camera on a new router.I've been able to reset the cam to factory defaults and see it wired using dhcp. I then was able to change the address to a static address, still wired and still can see it with IE. However when I disconnect the rj-45 cable, power down and restart, I can't access the cam.
View 2 Replies View Relatedif there is a MIB for monitoring temperature on a Cisco 800?
View 2 Replies View RelatedI am trying to find out what the 'normal' operating temperature of the CPU in a 3945 router is? We have just replaced some 2800 routers for 3945's and the NMS server initially complained about the new router CPU temperature being too high. Compared to the 2800 the CPU temperature is much hotter - 50 degrees celcius as opposed to 20-smothing degrees. I have searched but can't find what are considered 'normal'?
This is the output:
router#sho environment allSYSTEM POWER SUPPLY STATUS==========================Internal Power Supply 1 Type: DCInternal Power Supply 1 12V Output Status: Normal
[Code].....
I'm looking for temperature monitor (HDD, CPU) that can be run with parameters, and have cmd result output.I need some software to monitor temperature in Labtech software.
View 12 Replies View Relatedwhy getting temperature event in 3560 switch, and we checked the Network room Temp it's normal around (22).
View 8 Replies View Relatedhow do I monitor temperature of my 1921 router? Which commands do I need to put on router and which MIBs to use. I am using PRTG network monitor as a monitoring system.
View 10 Replies View RelatedWe bought two packs of IPCAM online from a vendor named HooToo, who seems have different online sites for selling various surveillance cameras. What we purchased is a unit with model no. of HT-IP206, according to its advertisement it has a storage temperature as low as minus 10 degree, and adversely high up to 60degree. While on the other hand, it states that the operating temperature shall be strictly between zero and 55degree. What Im concerned is that what if temperature drops down to minus when a camera is fully operating? Shall extra heating system be needed while the real temperature fails to meet the above-said requirement?
View 4 Replies View RelatedWhat is the difference between Operating temperatue & storage temperature of switch C3560E ?
View 2 Replies View RelatedI have load CISCO-ENVMON-MIB and initiate walk in it but unable to find OID of Cisco 2960 temperature monitor. I have search over net and found .1.3.6.1.4.1.9.9.13.1.3.1.3.1 for temperature but this OID is not responding in this mib.
View 2 Replies View Relatedi have 3560 switch located in warehouse environments . i need to monitor the temperate of this switch . i am looking for OID value that serves this purpose .
kindly provide me how to look for all OID that give me real time status for FAN .. CPU UTILIZATION ...TEMPERATURE ...OR ANY MAJOR EVENT THAT CAN DISRUPT MY PRODUCT IN .