Cisco Wireless :: 3500 - Any Door Access Point Which Can Operate In Very Low Temperature
Feb 23, 2011
Recently i have visit some site for survey of wireless (WiFi). My client ask to provide the Access Point inside the Cold storage of factory( For RF scanners) The temperature of the place is -25 C to -30 C. I have go throug the wireless option of cisco like 1200 series, 1100 series, 3500 series, but all of these operate maximum of -20C. while only out door access point ( cisco 1500 Series ) support such low temparture.
View 13 Replies
ADVERTISEMENT
Jan 17, 2013
i access points in our network.I want to connect with 3550 switch but access point is not working and getting the below error
controller port error.
IOS image --=c3550-i9q3l2-mz.121-20.EA1a.bin
Switch Model---WS-C3550-24PWR-SMI
I want to know ,this access point is supported on this switch ?
View 17 Replies
View Related
Nov 21, 2012
links with information / guidelines for the initial setup for this Access Point?
View 7 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Jul 1, 2012
The problem am having is that my Users can get to the internet on the LAN but cannot get to the internet thro the WLAN. Below is the cisco equipment used to setup the WLAN and LAN. I dont have any clue as to why users cnnot get to the internet from the WLAN except the LAN.
ITEMS
1.
CISCO CATALYST 2960-S
Part Number: WS-C2960S-24PS-L
10
Part Number: CON-SNT-2960S2PS
10
[code]....
View 5 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Jul 14, 2011
I have a customer who bought Cisco Aironet 3500 Series. Currently 4404 WISM Controllers are installed with 1142 Access-Points. The WLC-Version is 6.0.199.
Will the 3500 Series Access-Points work? (Of course without the spectrum intelligence feature)?
The Q&A says the following: Are there any concerns with supporting the new Cisco Aironet 3500 Series Access Points with the older Cisco 2000, 2100, 4100, or 4400 Series Wireless LAN Controllers?
View 2 Replies
View Related
May 21, 2012
I am upgrading a large number of 1142 access points with 3500's does and one know if the back plate for the 1142's can be reused for the 3500's.
View 4 Replies
View Related
Jun 29, 2012
I can't find info about Access Restrictions in new series of routers.[URL]Do new routers have both Parental Controls + Internet Access Policy? I need this [URL]
View 2 Replies
View Related
Mar 20, 2013
My next door neighbour has just installed a Virgin Super Hub and has 2 Homeplugs on his network. I have a Netgear router and 2 netgear homeplugs on my network, His network is giving my wireless router an IP address which changes my default gateway. Can I stop this by changing my default gateway and subnet mask? if so how and what to?
View 8 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Sep 12, 2012
A friend has 2 Asus RT-N66U's for the purpose of extending wifi range from her small companies shop to her house which is next door from each other.
from the house I can connect to the first router via wifi with a decent signal strength but what I need to do is backhaul from the other router via wifi and then have another wifi network in the house.
can this be done with just the 2 routers, or should I be looking for a cheap point to point setup and 2 separate routers?
View 1 Replies
View Related
Jun 11, 2013
How to configure ssh in all access points ( cisco 3500 Access points ) under wlc 5508 ?
View 3 Replies
View Related
Jul 8, 2012
I have Cisco AP 1142 standalone and I want this one to operate with WLC.
I have searched in Google, they said I need to upgrade AP1142.
I don't know how to upgrade it.
View 6 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Oct 18, 2011
I selected: Static IP
Static IP:192.168.0.100
Subnet: 255.255.255.252
Gateway:192.168.0.1
DNS: 60.49.166.105
I am a Malaysian, using Streamyx here, I search some articles shows that the ISP given is 60.49.166.105 or 60.49.166.106. Am I right in the setup? Why I am still unable to online though successful to connect after the setup configuration?
View 1 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
Feb 10, 2012
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies
View Related
Nov 6, 2012
I have my broadband line feeding into a WAG 320N in an outside room. There are computers in the outside room which are wired to the modem via CAT leads & plugs. Wireless is turned on, but is not currently being used in this room, as the wired connections work fine. From this outside room there is an underground cable (12 metres) to the house, which through a CAT lead is plugged into another WAG 320N, which operates primarily wirelessly, so laptop computers can be used in the house wirelessly. When the outside room modem is turned on AND the house modem is turned on, only one modem OR the other can access the internet, NOT BOTH. Why can't both modems operate wired and wirelessly. What is the problem? Is there a conflict between the two wireless signals? Can/ should I turn off the wireless signal from the outside modem (if so HOW?) . OR is there a way I can have both modems transmitting a wireless signal.
View 1 Replies
View Related
Jun 20, 2011
I'm looking after any driver wich can operate the WUSB600N v2 under Windows 98 at an old computer who is not able to operate with WinXP.Is any "freak" there who knows wich driver can be used for it? (Perhaps as well an older driver from any other older CISCO wlan stick ... ?)
View 2 Replies
View Related
Feb 23, 2012
I have a E4200 router. The firmware version is 1.1.02. I am reluctant to upgrade; however, my iMAC is picking up the 5GHz broadcast setting, but the rest of my wireless devices only recognize my lower 2.4GHz setting. I have changed channels, my router address is changed because it conflicted with my Verizon DSL. I do not have FIOS. What can I do to fix this problem. I have an ipad, 2 iphones, 2 ipod touches, 2 laptops (PCs), an XBOX, and a PS3 that needs to connect to a higher broadcast. The connections are slow and at times get dropped.
View 4 Replies
View Related
Dec 17, 2009
The operating temperature for 2100 wireless lan controllers is up to a miximum of 40 degrees celsius according to the datasheet. We deployed some 2112 controllers all displaing a temperature above 50 degrees celsiun. This during normal operation and deployed proper enviromet (aroco ...)
View 2 Replies
View Related
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
View Related
Jun 4, 2013
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
View 11 Replies
View Related
