I have router cisco 1006 ... when I no shutdown the interface this appear to me.
Router(config)#interface gigabitEthernet 2/1/0 Router(config-if)#no Router(config-if)#no sh Router(config-if)#no shutdown Router(config-if)# *Jan 20 08:50:01.239: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/0, changed state to down *Jan 20 08:50:01.140: %LINK-3-UPDOWN: SIP2/1: Interface GigabitEthernet2/1/0, changed state to down.
I have 2 ASR 1006 with ASR-1000-ESP40, ASR-1000-SIP40, ASR-1000-RP2 , and with SPA-1X10GE-L-V2 that should hold an XFP-10G-MM-SR.
i am in the proceed of an implementation and configuration, but i am facing a problem on the interfaces, where i am not able to bring the interfaces up/up and always down/down.
i check the fiber patch cords and the other SFP on the switch WS-C3560E-12D and it is working fine. i also reverse the fibers pins and nothing works
i need only to get the interface to be up/up. i also checked all the hardware compatibility matrix, IOS XE, the SPA are all online (show platforms).... where all seems to be ok and compatible.
all what is needed is to give the interface ,for example, tengig0/0/0 and ip address and no shut and it should go up/up.
One more thing, the XFP is not giving a red light laser, and in the show interface tengig0/0/0 give media type is unknown.
No date in the TOP-N Interface Errors portlet showing in LMS 4.1, but data for TOP-N Interface Utilization is displayed like expected. The Interface Errors poller show active(without errors) with same Instances as Interface Utilization.
View 1 Replies View RelatedI am using a Cisco ME 3800 switch with 24 Gig and 2 Tengigabit interface. But after configuring the Tengig int with ip add and negotiation it is no know visible in the switch. Instead TenGig I am seeing two (Gi0/1 and G0/2). Not even showing the Tengig in the running config.
View 3 Replies View Relatedsome of the servers are not pinging from one switch but they are pingable from other redundant distribution switch. So I took the IP addresses from the redundant switch, with that I found MAC addresses from the access switch.But when I tried to see to which ports these MAC are addresses are connected to, multiple MAC addresses are resolving to the same switchport. like 5 MAC's are showing to 1 port and other 3 MAC's are showing to other port, like this there are many. All these MAC's belong to virtual servers.
View 11 Replies View RelatedWhat would cause an interface to show up/up (looped), but you still can't ping that loop?...It is on a Cisco 7613 with an Enhanced FlexWan (WS-X6582- 2PA), with a Mx Serial PA, 8 ports (73-1580-10) and running IOS ver 12.2(33)SRE2 [code]
View 5 Replies View Relatedwe have a cissco 4506-e switch with ios version 03.02.05.SG . We ae currently facing a strange problem . Vlan interfaces configured in he switch are not showing input and output traffic, whereas the traffic is seen on the Gig interfaces mapped to the respective vlans . We also tried configuring the load-interval 30 , but there is no change . Interace 3/5 is mapped to vlan 5 . For this issue we have also done the IOS upgrade from 3.1.1SG to 3.2.5SG recently still the issue is same. [code]
View 2 Replies View RelatedWe have 3 Cat 4500 switches on three floors teh 3rd floor switch connects to the 2nd and 4th floor switches ,but we are receiving an alert from monitoring tool that " Interface(314) Backup-1Gb-Ring is Down at least 2 min on Switch: SOM500-4510-3FL the following output from "sh int status module 1 " shows the int 1/3 and 1/4 are 'inactive'local IT guy said If the status is inactive,the ports cannot be used and might lost the capability when he added 48-port blade into the 10th slot.
2nd Floor
Port Name Status Vlan Duplex Speed TypeTe1/1 SOM500-Core1 connected trunk full 10G 10GBase-LRMTe1/2 SOM500-Core1 connected trunk full 10G 10GBase-LRMGi1/3 Backup-1Gb-Ring notconnect 1 full 1000 1000BaseSXGi1/4 Backup-1Gb-Ring connected trunk full 1000 1000BaseSX
3rd FloorPort Name Status Vlan Duplex Speed TypeTe1/1 SOM500-Core1 connected trunk full 10G 10GBase-LRMTe1/2 SOM500-Core1 connected trunk full 10G 10GBase-LRMGi1/3 Backup-1Gb-Ring inactive 1 full 1000 1000BaseSXGi1/4 Backup-1Gb-Ring inactive 1 full 1000
[code]....
I always though that sh mac address table dynamic interface xx/xx/xx was a subset of "sh mac address table" 6590 Version 12.2(33)SXI I have two mac addresses on downstream switches that will only show up when using
sh mac address-table dynamic interface Te4/10
* 903 0050.77a9.6e3c dynamic Yes 0 Te4/10
* 903 0050.77a9.5766 dynamic Yes 0 Te4/10
when using "old faithful"
sh mac address-table | inc 6e3c
*nothing*
or
sh mac address-table dynamic | inc 6e3c
*nothing*
nothing shows up?this vlan has no layer three interfaces
I am trying to configure a 4507 R chassis with Dual SUP but i cannot see teh switchpot mode trunk encapsulation dot1q?
I have typed:
interface GigabitEthernet5/1
description DOWNLINK toxxxxxx
switchport mode trunk
channel-group 11 mode on
!
I have have searched all other commands and sub-commands but could only find dot1q-tunnel which I beleive is for QINQ or some QoS featues and lot for L2 encapsulations?
the puzzling is:
XXX-Core4507#sh int gi5/1 trunk
Port Mode Encapsulation Status Native vlan
Gi5/1 off 802.1q notrnk-bndl 1
(Po11)
when I connect the dostribution switch a 3507 to this int gi 5/1, both interfaces do come up?
I'm currently working on a plan to migrate our 6500's over to our new 7010's. At the time of the migration I want to tighten up our OSPF design and configure OSPF for "passive-interface default" then allow only those interfaces that should have OSPF neighbors to send the hellos. The issue is that the command is not showing up under the OSPF process. What's even more interesting is that the Nexus 5.x Unicast Routing Configuration Guide shows that the "passive-interface default" command should be an option to enter.
I'm currently running version 5.1(4) (though looking to upgrade to 5.2 during my migration testing). I would rather configure the passive-interface via the routing process versus having to enter it on every interface.
The active RP of ASR 1006 router automatically switched over to standby while the standby assumed the active role.Not sure the exact reason for this behaviour. The image version is 122-33.XNB1. We noticed an outage when the switchover happened but the device did not crash.
%CMANRP-6-CMHASTATUS: RP switchover, received fastpath becoming active event%CMANRP-6-CMHASTATUS: RP switchover, received chassis event to become active%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_NOT_PRESENT)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_DOWN)%REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_REDUNDANCY_STATE_CHANGE)%PLATFORM-6-HASTATUS: RP switchover, sent message became active. IOS is ready to switch to primary after chassis confirmation%NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun%CMANRP-6-CMHASTATUS: RP switchover, received chassis event became active%PLATFORM-6-HASTATUS_DETAIL: RP switchover, received chassis event became active. Switch to primary (count 3)
In the output of "show redundancy switchover history" the switchover reason given is active unit failed.But currently the RPs are working as active and standby hot.
after configuring around 20 static ip routes on my ASR, and doing a 'show ip route' it doesn't really show anything.Do I need to enter another command or something, or is it because, all interfaces on the ASR are down right now, since I'm just putting the configuration on it.It currently has no reachability to the next hop for all routes, since it has no live connections on the ASR yet.
View 1 Replies View RelatedWe are trying to upgrade our ASR1006 with single RP. We got an Warning message as "superpackage install over superpackage not allowed on active RP"
how to do the upgrade properly?
I have a ASR 1006 router in my environment and I want to make it a DNS server for some reason. I tried to configure the command IP dns server on the ASR but it does not accept the command. I also have a Cisco 7206 VXR router in my environment which acepts this command.
The IOS version of my ASR is IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.1(3)S2.
New to Cisco devices and have had an ASR dropped in my lap.Running ASR1000-RP2 with System image file: asr1000rp2-advipservicesk9.03.03.00.S.151-2.S.bin Show Vlans returns: No Virtual LANs configured Router(config)#interface vlan?
<1-4095> Vlan interface number
But when I try an assign a Vlan number I get % Unrecognized command, or % Incomplete command
My problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
We are having Cisco ASR 1006 Router with the XE Code :asr1000rp1_advance entrprisek9.03.01.00.S.150_1.S.bin The basic information we are having is
cisco ASR1006 (RP1) processor with 1717513K/6147K bytes of memory.
10 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
937983K bytes of eUSB flash at bootflash:.
39004543K bytes of SATA hard disk at harddisk:.
Wanted to upgrade to the latest IOS XE 3.4.x but the memory requirement for this IOS is Dram 4GB. But the DRAM actually is 2GB as per show version command.Here the Physical memory is showing 4 GB so can we upgrade this IOS XE?
I saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies View RelatedI am trying to bring up a couple of ASR's. They are fitted with SPA modules (SPA-8X1GE-V2). These have SFP modules GLC-T fitted into them. For the life of me I cannot get these ports to come up. If I have a look at the inv the SFP's show as GE-T's (physically they are GLC-T's)
Is there a compatability problem with these GLC-T's on ASR 100x?
I am facing some issue to activate ,SPA-5X1GE-V2 modules on ASR 1006.
View 1 Replies View RelatedIf I implement IKE V2 on Cisco ASR 1006 Router or on firewall and sets up IPsec with IKEv1 device ( Cisco Router , Juniper etc )will it work or not ?
View 6 Replies View RelatedWe have ASR 1006 with IOS XE and i want to see the Software License but somehow i cant!!! ...i googled it but i could not find anything.how can i see the available license on ASR 1006 or 9000 series?
View 1 Replies View RelatedEarlier this AM I got an email from one of our distributors... So I began to print it. Then I realized that it was over 100 pages long. I decided to stop the printing job at that point. The printer kept printing the job still... even though I told it to cancel like 50 times.
Only thing I could thing of from there was to reboot while the printer was still going. Upon reboot I found a weird issue. Now the printer will not work with the laptop on the network.
Its prints fine on my machine... but now the laptop can only see the printer but not use it. I go to set it as the default in that machine and it says it will DL the drivers for use on printer. When I do that it just returns an error.... can not connect to printer.
I have tried to use the manual method of using a manual port setting but it just returns an access denied. How I can get this printer working on that machine. I have tried searching online for this error.
We are connected to 2 different providers (PROV01 and PROV02) with eBGP full internet tables. PROV01 routes have higher local preference over PROV02.
We are having problems with our provider and would like your expertise. PROV01, higher preference has been having trouble with their router. The BGP remains up but the router stops forwarding traffic. as a resulta we lose connection to the internet but our traffic never goes to PROV02 since PROV01 BGP remains up announcing the 400K routes to us.
Is there a way to test internet connection though PROV01 and as the "internet is DOWN" automatically change traffic to PROV02? Can BGP parameters changes be triggered by IP SLA? Our router is an ASR1006 RP2.
my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies View RelatedI've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
View 14 Replies View Relatedis ASR 1006 supported span port or port mirroring? Any config about that?
View 2 Replies View Relatedi check ASR 1006 config with ESP-40, the firewall permonce can reach 40G, ASA 5580 is 20G, can ASR 1006 replace ASA 5580, is there any function feature problem?
View 1 Replies View Relatedi have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies View RelatedI have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
Is it possible to set up a WAN interface on a FastEthernet interface of a Cisco 877 Adsl Router ?Due to my ISP, i've to use an external VDSL modem and must connect it to my cisco 877 router (and leave it's adsl interface unused).But i don't know how to set up a wan port, other than the adsl interface itself (dialer0), on my cisco.
View 7 Replies View RelatedWe are having Cisco ASA 5540 having Cisco Adaptive Security Appliance Software Version 8.0(5)23 at certain time of moment daily wer are facing latency and packetdrop wherin when I checked for ASA Interface which gives me " Input Errors" on outside interface ,so can any one tell me what are the causes to get input errors on cisco asa outisde interface.
View 2 Replies View Related