trying to upgrade an 1811 to the latest firmware. [code] just seems to always boot back to the original file and not the one i just tftp'd up. could it be that this router requires additional ram to support this ios?
View 5 RepliesHow to force the Cisco 1811 Router to read a Transcend CF 128MB? [code]
View 2 Replies View RelatedI got a new 1811 series router. Its sh version output is " flash:c181x-advipservicesk9-mz.124-11.XW6.bin". I need to upgrade to the latest IOS. How can i find a latest one? How can i upgrade to the latest one?
View 1 Replies View RelatedI have an 1811 configured with dhcp scope and generally it works correctly. I have a host on the vlan/subnet that the scope is assigned that can receive an IP and all the specifics from the dhcp server. [code]
The host on the vlan/subnet should use the router as the dns server to resolve static hosts that are configured on the router itself. Can an IOS DHCP/DNS server do this?
How do I upgrade the boot rom version on the 7200 router? I am running IOS Version 12.4(22)T and when I plug in the serial ds3 card in my router it keeps rebooting with a watch dog error ( see below). Also, what version should I upgrade to?
Router#sh verCisco IOS Software, 7200 Software (C7200-SPSERVICESK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Fri 10-Oct-08 10:10 by prod_rel_team
ROM: System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Router uptime is 0 minutesSystem returned to ROM by power-onSystem image file is "sup-slot0:/c7200-spservicesk9-mz.124-22.T.bin"
[code]....
I am going to be updating the IOS on our Cisco ASA 5520 from verion 7.0(8) to 8.2(5). I am also going to setup AnyConnect. Are there any major changes in the 2 IOS versions that I need to be aware of or will the config work in either version? Also, we are currently using the Cisco VPN Client to connect to our network. Will that still work after the upgrade?
View 3 Replies View RelatedI´m about to upgrade a customers appliance box to PI 1.3. I am guessing an upgrade to 1.2 would be almost the same, license wise.
View 10 Replies View RelatedI need to know how to do the upgrade from WCS 7.0 to Prime Infrastructure 1.2.
I was reading and i need to upgrade to the NCS 1.1 before to go to prime infrastructure 1.2.
I will need license to NCS 1.1 before upgrade to infraesctructure 1.2 ?
Will i have some problem with this upgrade ? correct process for not have any problem with this upgrade ?
I have upgraded NCS 1.1.1.24 to PI 1.2 lately. The installation process completed successfully.But now i am not able to log in to the GUI anymore as root. After entering the password all I get is a blank site (undefined).I get the same result with all known browsers. Rebooting or restarting NCS does not change anything.
View 12 Replies View Relatedafter an upgrade of NCS 1.1.1.24 to CPI 1.2 on green field, it was not possible to reuse the GUI. During the upgrade, I''ve shortly seen an oracle DB error, but the upgrade was going through, without problems.At the end, it was not possible to use the GUI, and every trial to start the services was stopped with errors.I've found the following severe Bug ID's in the support forum: Bug CSCuc29378 Prime Infrastructure 1.2 won't start after a db restore/Upgrade from NCS1.1.1.24 Oracle DB bug as well: CSCtw59460.I see only a new installation from scratch (1.2) as solution, but the bug is not resolved in V1.2, as seen in the bug tool.
- As the customer has an v.1.0 license who worked with NCS 1.1.1, do I need an upgrade order to be able to activate an installation from the v 1.2 ova (new PAK)??
- I'm searching for a one year CPI partner license, because I heard about in some Cisco Live sessions, but I did not find a way to acces´s to it.
Im getting a bit confused about the whole upgrade migration process for the following config to Cisco Prime Infrastructure:
LMS - Version 4.1 , 500 devices. Windows Server 2008 R2 Standard SP1
NCS – version 1.1 , 50 devices Red Hat Linux ( 64 Bit) (Installation software - NCS-VA-1.0.1.4-small.ova)
I want to be able to backup databases and migrate licensing from LMS and NCS to one platform.
I have a client who has LMS 4.1 with SAS support, I know that I can upgrade him to the Prime infrastructure for LMS and NCS, however he is licensed for 100 devices. He also has WCS 7.0 with 50 AP licenses, I want to upgrade his LMS to Prime infrastructure and then migrate his WCS to NCS, but how do I know combine the both so that he is on one platform.
View 1 Replies View RelatedWe just purchased the following items:
(1) R-PI-1.1-500-K9
(2) PRIME-NCS-APL-K9
I want to know how I can upgrade to the latest version of Cisco Prime Infrastructure.
I am running 12.3(11) T8 on Cisco 2821 platform and trying to upgrade to 15.0. No luck. So I tried to upgrade it to 12.4 24T. But failed several times on different routers. Is there an intermediate version I should land before jumping to 12.4 24T?
View 3 Replies View RelatedI am upgrading the network equipment at my place of employment. We use Cisco C3560, 2960, 4506 and I was noticing that IOS 15.0.x is available. After doing some reading it appears that Cisco is going to a pay for the licensing functionality that you want. Do I need to purchase licenses to upgrade from IOS 12.X to 15.0.x to maintain functionality?
View 4 Replies View RelatedAny thoughts on Cisco putting a quad core processor in some near future version of this card?, the current versions are simple dual processors that does not give you much to work with if running ESXi 5 on one of the vCPUs.
View 1 Replies View RelatedI recently installed a firmware upgrade on my E3000 to firmware version 1.0.04.build 6. Since the upgrade I am unable to see any of my files on my network computer which is running windows 7. Before everything was fine and I could stream to my dvd players and dish receivers.
View 1 Replies View RelatedI have a cisco router 1811 when powered displays the output below then it hangs at that point.
System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 2006 by cisco Systems, Inc.
C1800 platform with 393216 Kbytes of main memory with parity disabled
[code]....
i set up a CISCO 1811 as routeur for different vlan's but it appear that i can't add a new vlan i'm limited to 14
all vlan trunked on a iface (Fast0) and just one vlan untagged to another iface (Fast1) go to gateaway i manage routing access with ACL_ip
do you know a model from cisco let me do it for more thant one undred vlans ?
I seem to be having an issue where certain very packets are being dropped/lost by my office router. The reproducible situation is, when I attempt a DNS zone transfer from my linux bind DNS server (A.A.A.A) to any server on my network behind NAT (Y.Y.Y.Y) the first packet (Seq 1) of the response is lost. The client making the query asks for first packet (Seq 1) to be resent, and the DNS server attempts to resend it repeatedly, but those are lost too.
View 10 Replies View RelatedI have a cisco 1811 router with 12.4(6) IOS, I would like to ask can I use this as a layer 2 switch?
When I issue vlan ID command it gives me " Invalid input detected", I need use this device as switch to create different vlan on and the connect the f0 port to a ASA
I'm trying to configure a Cisco router 1811 for Internet access, so here's my scenario:
2 ISP:
1º - 66.110.117.33
2º - 64.30.154.81
Internal Server:
172.16.30.2
how can I make all this traffic(SMTP,pop3,http,HTTPS,DNS) available in both interface?
I have an 1811 as a border router. Initially we had one block from our ISP. We just got a second block of IP's and I'm not sure how to make this work.
Block #1 - Working
209.91.**.129-142 /28
Block #2 - Not Working
209.91.**.146-158 /28
The problem I'm having is block #1's gateway is 209.91.**.129 and block #2's is 209.91.**.145
How do I make it so I can use both blocks in my NAT entries?
I have manual Cisco 1812 (1811) Integrated Srvice Router Cabling and Installation in front of meI have Cisco 1811 connected to my laptop according to this manualI have Cisco SDM latest version installed on my laptopI have DHCP enabled on my laptopThe problem that my laptop can't get valid IP adreess from the router (see att. laptop_, laptop_2)
Which IP address I have to use in order to get access to router inrerface (see. SDM_1)?
Basically, he has an office he's supporting on a contract basis, they have a cable modem uplink. They move very large (100MB or so) EXCEL files to/from a server "somewhere out there"...The place has 19 users on cable modem (presumably commercial level). They're having "severe latency due to all the users". They're also using VOIP (not sure what product, shouldn't really matter)this doesn't pass the sniff test to me- I have 70+ users on 4 T1s and don't have the problems they claim to be having. Suspect they should be doing some packet sniffing to see who's camping on Youtube, but this is not an option....They're adding in a second cable modem line and want to bind both together. I immediately figured they should do QOS, dedicate the mission-critical traffic to 1 line and let it bleed over onto the other and take precedence if necessary. They have a Cisco 1811 router. I haven't messed with those before, but what I am seeing is they are a "fixed-configuration router". Obviously there has to be SOME config changeable- if for nothing other than IP assignment to interface and such. So what does Cisco mean by "fixed-config"? Is this basically a dumbed-down Linksys router?
View 19 Replies View RelatedI need some help in configuration of Cisco IOS VPN. Basically, we have 2 Cisco 1811 routers in our company. Router 1 - Production router (IP 192.168.x.254)Router 2 - VPN router (IP 192.168.x.251). All machines/servers inside our network has been configured with a default gateway of 192.168.x.254. Hence, all internet traffic will go through the production router.
Now, we want to deploy a new router (i.e. Router 2) which will be solely used for VPN purpose (such as DMVPN, IPsec site to site, VPN client configuration etc). I have configured Router 2 with Cisco VPN client and can connect to this using VPN client application from my home PC. However, once I connect to it, I am not able to ping anything inside this network other than Router 2 IP (192.168.x.251).
Is there anything else that I would need to put into the configuration so that I can ping everything inside the network?
i have cisco router 1811 , i make port forwarding for my mail server , so from outside i can access to the mail server via my mobile but inside lan i cannot because i use my global ip address at my mobile config .
View 12 Replies View RelatedI have some problems with making stable VPN between SRP512W and ISR1811.Configuration:
- IKE policy - 3DES/SHA1 group2(1024bits)
- crypto map on ISR1811
One of the main issues I've noted appears when SRP loose it's IP connectivity to remote router, even if this connectivity interruption lasts for only couple of seconds. When the IP connectivity is restored SRP is unable to re-establish the IPSec session. There is connect/disconnect option in SRP menu (Status -> VPN Status -> Connect/Disconnect) and automatic VPN disable (VPN -> Site-to-Site VPN -> IKE policy -> Enable Dead Peer Detection) yet I couldn't found any option for nor automatic mechanism for VPN reconnection when the IP connectivity is reestablished. This issue lead to interruption of Site-to-Site VPN service when there is some short outages within the ISP network.
Another issue is building GRE tunnels between the same devices. Can you verify my configuration? Belive it or not - I spent more than 4-5 hours and couldn't do it.Should I make some additional settings/configurations ?
i have two branch offices A & B both connected by a vpn. i am planning to add another isp on both the locations and have it just for the vpn. i.e have the second isp do just vpn and all other traffic go through the older ISP.. what are my options ? am not planning to add any extra hardware and also am not planning on acheiving any fail-over or load-balancing because i know ASA 5510 does not do load-balancing.
View 1 Replies View RelatedI am a new owner of a Cisco 1811, brand new. So im trying to follow this,
[URL]...
But when i get to this,
it won't continue, if i cancel this and not setup the WAN connection then log back into after it's rebooted i can see both lan's * both disabled * when i enable 0 it wont allow me to click add or do anything else to setup the WAN connection
I am setting up my 2nd 1811 router for NAT and VPN. The 1st 1811 works great, completed a few months ago. On this 2nd 1811, I decided to just copy the working startup-config from the good, 1st router to this 2nd, and then change IPs and from there. I did not do the setup wizard, but just erased the startup-config, reloaded, gave temp IP on local LAN and copied good startup-config from TFTP server.
Question: on this 2nd 1811, I show this:
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no ip subnet-zero
I do not have this on the 1st, and I cannot get rid of it. Is this due to IOS versions?
On the 1st I have:
Cisco IOS Software, C181X Software (C181X-ADVIPSERVICESK9-M), Version 12.4(6)T8, RELEASE SOFTWARE (fc3)
flash:c181x-advipservicesk9-mz.124-6.T8.bin
On the 2nd I have:
Cisco IOS Software, C181X Software (C181X-ADVIPSERVICESK9-M), Version 12.4(4)T1, RELEASE SOFTWARE (fc4)
flash:c181x-advipservicesk9-mz.124-4.T1.bin
I am having an issue where the GRE tunnels are up/up but are not pingable. The GRE tunnels are on a cisco 1811 and cisco 2811 routers The tunnel source and destination IP addresses are private addresses. These private addresses are pingable to each other and they are connected via IPSEC. The IPSEC tunnels are generated from the ASA to which the cisco routers connect. Probably the tunnels are up/up because keepalives are not configured. But I am still not able to see why I cnt ping the end points. The ACL for IPSEC in ASA includes the "permit gre host <Private IP 1> hist <Private IP 2>" commands.
View 2 Replies View RelatedLast night I had a crack at setting up PBR on my companies Cisco 1811.Joy, I thought, it's actually working. Alas I was wrong, the addresses were getting translated to our ADSLs external ip address but routed over our EFM.What I want to acheive is to send all HTTP(s) traffic from our workstations over the ADSL (FastEthernet1) whilst all other traffic and VPN goes out over our Bonded ADSL (FastEthernet0). There is also a minor failover in place for traffic routed to the ADSL in the route-map PBR_VLAN1. The servers are on IPs 200, 202, 204 and 240.
Anyway, I have re-written the configuration and xxx'd and x.a/b/c'd all the IP addresses I want to keep secret. Need to make sure that the PBR is correct, and will do what I want it to? I have a very small time-frame to get this correct and I dont want to fudge the bucket so to speak.