i set up a CISCO 1811 as routeur for different vlan's but it appear that i can't add a new vlan i'm limited to 14
all vlan trunked on a iface (Fast0) and just one vlan untagged to another iface (Fast1) go to gateaway i manage routing access with ACL_ip
do you know a model from cisco let me do it for more thant one undred vlans ?
On interface FA0 goes the UTP from my ISP. Further more I have setup my Vlan1 but i can't connect to the Internet.
Building configuration...
Current configuration : 3649 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]...
Although I am quite used to using the WLC 4402 and the attached APs, I have no knowledge about licensing and I'm wondering if it has a limited number of AP's that can be controlled by the WLC? I'm not planning on adding 1000's but at the moment we have 21 and will probably be adding an additional 30 in the near future.
View 1 Replies View RelatedIf multilayer switch has routing capabilities then why we can go for dedicated router?
Why we cannot use a number for VLAN ID other than 1 to 4094 ?
we have inserted into a network with VTP a Cisco Switch 2960-S, not knowing that had installed IOS LAN lite.Now I discovered that it can handle up to 64 vlan. In the network there are currently configured 62 VLAN: what happens when we exceeded the max number (64) of VLAN for that switch?
View 6 Replies View Relateda number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.
View 1 Replies View RelatedThe SRP547W supports creating both Wifi Voice and Data vlans.Can I configure a Wifi IP Phone to connect to the SRP547W Voice Wifi Vlan and have the SRP associate it with Line 1 (in lieu of a standard phone connected to the Line 1 FXO port - without additional hardware)?
View 1 Replies View RelatedI got a new 1811 series router. Its sh version output is " flash:c181x-advipservicesk9-mz.124-11.XW6.bin". I need to upgrade to the latest IOS. How can i find a latest one? How can i upgrade to the latest one?
View 1 Replies View RelatedI have some tunnels which terminate to my home router. I'm allowing the other ends of the tunnels to use my voice setup. I need to prepend *67 to all called numbers which don't originate from my house. I don't want people calling my home number based on the caller-id number they see when someone across one of the tunnels calls.
So if 5008 calls 212-333-4444 I want it sent to my provider as *672123334444. If 5001 calls a number, I don't want it touched. Can I do this? I can use IOS or CUCM here.
I have a cisco router 1811 when powered displays the output below then it hangs at that point.
System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 2006 by cisco Systems, Inc.
C1800 platform with 393216 Kbytes of main memory with parity disabled
[code]....
trying to upgrade an 1811 to the latest firmware. [code] just seems to always boot back to the original file and not the one i just tftp'd up. could it be that this router requires additional ram to support this ios?
View 5 Replies View RelatedI seem to be having an issue where certain very packets are being dropped/lost by my office router. The reproducible situation is, when I attempt a DNS zone transfer from my linux bind DNS server (A.A.A.A) to any server on my network behind NAT (Y.Y.Y.Y) the first packet (Seq 1) of the response is lost. The client making the query asks for first packet (Seq 1) to be resent, and the DNS server attempts to resend it repeatedly, but those are lost too.
View 10 Replies View RelatedI have a cisco 1811 router with 12.4(6) IOS, I would like to ask can I use this as a layer 2 switch?
When I issue vlan ID command it gives me " Invalid input detected", I need use this device as switch to create different vlan on and the connect the f0 port to a ASA
I'm trying to configure a Cisco router 1811 for Internet access, so here's my scenario:
2 ISP:
1º - 66.110.117.33
2º - 64.30.154.81
Internal Server:
172.16.30.2
how can I make all this traffic(SMTP,pop3,http,HTTPS,DNS) available in both interface?
I have an 1811 as a border router. Initially we had one block from our ISP. We just got a second block of IP's and I'm not sure how to make this work.
Block #1 - Working
209.91.**.129-142 /28
Block #2 - Not Working
209.91.**.146-158 /28
The problem I'm having is block #1's gateway is 209.91.**.129 and block #2's is 209.91.**.145
How do I make it so I can use both blocks in my NAT entries?
I have manual Cisco 1812 (1811) Integrated Srvice Router Cabling and Installation in front of meI have Cisco 1811 connected to my laptop according to this manualI have Cisco SDM latest version installed on my laptopI have DHCP enabled on my laptopThe problem that my laptop can't get valid IP adreess from the router (see att. laptop_, laptop_2)
Which IP address I have to use in order to get access to router inrerface (see. SDM_1)?
How to force the Cisco 1811 Router to read a Transcend CF 128MB? [code]
View 2 Replies View RelatedHow do I get the number or password to my router, i have a nook and it was hooked up to comcast until i changed to verizon, now my nook can't find my network.
View 1 Replies View RelatedBasically, he has an office he's supporting on a contract basis, they have a cable modem uplink. They move very large (100MB or so) EXCEL files to/from a server "somewhere out there"...The place has 19 users on cable modem (presumably commercial level). They're having "severe latency due to all the users". They're also using VOIP (not sure what product, shouldn't really matter)this doesn't pass the sniff test to me- I have 70+ users on 4 T1s and don't have the problems they claim to be having. Suspect they should be doing some packet sniffing to see who's camping on Youtube, but this is not an option....They're adding in a second cable modem line and want to bind both together. I immediately figured they should do QOS, dedicate the mission-critical traffic to 1 line and let it bleed over onto the other and take precedence if necessary. They have a Cisco 1811 router. I haven't messed with those before, but what I am seeing is they are a "fixed-configuration router". Obviously there has to be SOME config changeable- if for nothing other than IP assignment to interface and such. So what does Cisco mean by "fixed-config"? Is this basically a dumbed-down Linksys router?
View 19 Replies View RelatedI need some help in configuration of Cisco IOS VPN. Basically, we have 2 Cisco 1811 routers in our company. Router 1 - Production router (IP 192.168.x.254)Router 2 - VPN router (IP 192.168.x.251). All machines/servers inside our network has been configured with a default gateway of 192.168.x.254. Hence, all internet traffic will go through the production router.
Now, we want to deploy a new router (i.e. Router 2) which will be solely used for VPN purpose (such as DMVPN, IPsec site to site, VPN client configuration etc). I have configured Router 2 with Cisco VPN client and can connect to this using VPN client application from my home PC. However, once I connect to it, I am not able to ping anything inside this network other than Router 2 IP (192.168.x.251).
Is there anything else that I would need to put into the configuration so that I can ping everything inside the network?
I have a BT Home Hub 3 and quite often get messages "cannot connect to network". I have many (>20) devices connected. Have I reached the limit? With four kids in the house the pressure to connect even more devices is growing.
View 1 Replies View Relatedi have cisco router 1811 , i make port forwarding for my mail server , so from outside i can access to the mail server via my mobile but inside lan i cannot because i use my global ip address at my mobile config .
View 12 Replies View RelatedI have some problems with making stable VPN between SRP512W and ISR1811.Configuration:
- IKE policy - 3DES/SHA1 group2(1024bits)
- crypto map on ISR1811
One of the main issues I've noted appears when SRP loose it's IP connectivity to remote router, even if this connectivity interruption lasts for only couple of seconds. When the IP connectivity is restored SRP is unable to re-establish the IPSec session. There is connect/disconnect option in SRP menu (Status -> VPN Status -> Connect/Disconnect) and automatic VPN disable (VPN -> Site-to-Site VPN -> IKE policy -> Enable Dead Peer Detection) yet I couldn't found any option for nor automatic mechanism for VPN reconnection when the IP connectivity is reestablished. This issue lead to interruption of Site-to-Site VPN service when there is some short outages within the ISP network.
Another issue is building GRE tunnels between the same devices. Can you verify my configuration? Belive it or not - I spent more than 4-5 hours and couldn't do it.Should I make some additional settings/configurations ?
i have two branch offices A & B both connected by a vpn. i am planning to add another isp on both the locations and have it just for the vpn. i.e have the second isp do just vpn and all other traffic go through the older ISP.. what are my options ? am not planning to add any extra hardware and also am not planning on acheiving any fail-over or load-balancing because i know ASA 5510 does not do load-balancing.
View 1 Replies View RelatedI am a new owner of a Cisco 1811, brand new. So im trying to follow this,
[URL]...
But when i get to this,
it won't continue, if i cancel this and not setup the WAN connection then log back into after it's rebooted i can see both lan's * both disabled * when i enable 0 it wont allow me to click add or do anything else to setup the WAN connection
I am setting up my 2nd 1811 router for NAT and VPN. The 1st 1811 works great, completed a few months ago. On this 2nd 1811, I decided to just copy the working startup-config from the good, 1st router to this 2nd, and then change IPs and from there. I did not do the setup wizard, but just erased the startup-config, reloaded, gave temp IP on local LAN and copied good startup-config from TFTP server.
Question: on this 2nd 1811, I show this:
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no ip subnet-zero
I do not have this on the 1st, and I cannot get rid of it. Is this due to IOS versions?
On the 1st I have:
Cisco IOS Software, C181X Software (C181X-ADVIPSERVICESK9-M), Version 12.4(6)T8, RELEASE SOFTWARE (fc3)
flash:c181x-advipservicesk9-mz.124-6.T8.bin
On the 2nd I have:
Cisco IOS Software, C181X Software (C181X-ADVIPSERVICESK9-M), Version 12.4(4)T1, RELEASE SOFTWARE (fc4)
flash:c181x-advipservicesk9-mz.124-4.T1.bin
I am having an issue where the GRE tunnels are up/up but are not pingable. The GRE tunnels are on a cisco 1811 and cisco 2811 routers The tunnel source and destination IP addresses are private addresses. These private addresses are pingable to each other and they are connected via IPSEC. The IPSEC tunnels are generated from the ASA to which the cisco routers connect. Probably the tunnels are up/up because keepalives are not configured. But I am still not able to see why I cnt ping the end points. The ACL for IPSEC in ASA includes the "permit gre host <Private IP 1> hist <Private IP 2>" commands.
View 2 Replies View RelatedI have a new wireless router which I have hooked up successfully to 3 computers , a playstation, and a WII on a secure network. My fourth computer refuses to save the new key. Ii keeps defaulting to an 8 digit number. It shows the secure network on availiable networks but won't accept the WPA key.
View 1 Replies View RelatedI am working at a client site today. This specific client has decided to replace their legacy 2600 branch office routers with newer 1921 ISR G2 routers as they move from a Legacy Frame WAN to a MPLS network with a different provider.
The backup in the former scenario was actually an ISDN solution. Moving forward, the provider has sold them a 3G backup solution. To support this, we have purchased Cisco line cards for the 3G. The part number for the cards is "EHWIC-3G-EVDO-V=".
I was asked by the client this morning if there was a way to tell what the IMEI number for the 3G card was. I performed a shew inventory, as well as a shew hardware, but I do not see this IMEI number. I also checked the label on the packaging box that the cards came in, but do not see this number. Is there a way to tell what this number is for each card?
I had to reset my Linksys WRT300N router because of issues with my internet provider and now I cannot get my Dell Inspiron E1405 to connect wirelessly. I am getting a status of limited or no connectivity with an ip address starting with 169. I have included the following:
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 2, 32 bit
Processor: Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz, x86 Family 6 Model 15 Stepping 6
[Code]....
I have a 100 Mbps router (which I can't change). But all my computers, media players/streamers, NAS have gigabit Ethernet. Currently, under exclusive use I do approach the 100 Mbps limit (seen a lot of times my laptop transferring files from/to NAS around 14 MBps). But since my devices are capable of handling higher speeds I am thinking to upgrade to a Gigabit switch. That brings me to my question.
If I have 100 MBps router and a Gigabit switch (1k Mac table), what will be max speed between devices connected through the switch?
I am aware anything that goes via the router will hit the roof at 100 Mbps. But will the devices under the switch operate at Gigabit (due to the direct transfer based on mac address)? Or will everything still go through the router who is giving out the IP addresses (the switch having no DHCP) and limit the speed?
I just bought a D-Link DIR-600.After I went through the setup wizard, I was able to get an internet connection, but it was useless (google search very slow, but connected). This was fixed when I disabled NAT, but that meant no other computer was able to access the internet through the router. This has all been wired. I still haven't setup the wi-fi.
H/W Version B2.
F/W Version 2.03
Internet connection is ADSL2+ through a NetGear DM111P. The modem is setup as PPPoE Bridging.
Can't find router number on my aspire 5750-6493
View 1 Replies View Related