My laptop has Intel(R) Centrino(R) Wireless-N 1030 internet card but the computer can not connect to the modem properly, the speed is always not the speed that I purchased
View 1 RepliesThe wireless on my laptop keeps dropping out. When I first got it it was fine, but after a while I started experiencing problems on every wireless network I connected to. Most of the time it would connect, but after around 10 minutes or so, the connection would drop out and the wireless card has to be "reset" so I can connect again. Otherwise I have a little yellow triangle over my network signal strength bars. I've updated to the latest drivers (14.2.0.10) but it was no luck.
This happens with every wireless network and I know it's not the network because my old Vostro 1500 is running just dandy on all of them.
The problem is that it always stays around 121-150mbps and sometimes 270mbps(beside router). here is my wireless settings on my router
router setting 1: [URL]
router setting 2: [URL]
network card setting:
802.11n channel width:auto
802.11n mode:Enabled
Ad-hoc channel:11
Fat channel intolerant:Disabled
Roaming aggressiveness :Medium
Throughput enhancement:Disabled
Transmit power:Highest
Wireless mode:802.11a/b/g
I have just taken delivery of a new Inspiron N5110 with an Intel Centrino N-1030 wifi card. I also have two dual band routers (LInksys WRT600N) in different locations in the house.
My problem is that the laptop is detecting my routers Wireless-G signals but NOT the Wireless-N signals. I have checked to ensure that the N-1030 card has 802.11n Mode set to Enabled and have also tried both setting under "802.11n Channel Width for band 2.4" (i.e. Auto and 20 MHz Only) with no success.
My routers are configured with the Wireless-G signal only on 2.4 GHz and Wireless-N only on 5 GHz. I found this to be the best setting to avoid interference from neighbors wifi and cordless phones and have been happily using Wireless-N with my other Dell laptop with no problems (XPS M1530 with Intel 4965agn wireless card).Does the N-1030 card not work with 5 GHz Wireless-N?
Well I'm typing from my tablet right now because for the 20th+ time, the Centrino 1030 card on my Vostro 3450 isn't connecting to hotel's wireless. Other places I have encountered it to have connection problems is colleges, universities, coffee shops, etc. It is also slow as molasses in my home too.
I have read other posts indicating similar problems without resolutions on the Vostro 3450. I am planning on replacing it with the BEST WLAN card there is. It seems a bit labor intensive from the service manual but doable. Has there been any "for sure" fix with the 1030 card?
The 1030 card is so incredibly bad that I am able to get 3/5 bars on my home network being outside while my Vostro can't even pick it up.
I have just got my new xps 17 and opted for the 6230, It only gets to 20 meg download speed, I can insert my old usb N adaptor and get the full 50 meg. I was on the phone for 2 hours last night with Dell, they had remote access and tried lots of things to improve the problem.
Finally once they saw that my old usb adaptor was much faster, they said a technician would call me back today betweek 12pm and 1pm or 4.30pm.
what other cards are compatible with XPS 13 Ultrabook? Like so many people, I have been having a problem with my wifi when the computer is used a little far from the router, and thinking about buying a new wifi card for a replacement (which is silly, and I shouldn't have to do, given my computer is brand-new and cost more than £1000, I know... but I don't seem to have much choice). I've tried everything that has been suggested in the Dell forums, and elsewhere, including those on the Intel site. But nothing has improved my connection even a bit.I have Windows 8 (64-bit). And it currently has an 'Intel Centrino Advanced-N 6235' wifi card that came with it.
View 2 Replies View RelatedI saw some other mentions online of intermittent internet connectivity using the factory-installed Intel Centrino wireless-N 1030 card on various new Dell computers running Windows 7, but didn't see any resolution to the problem.
I can connect directly to my router via an ethernet cord, but trying to use the wireless card gives me intermittent connectivity. I will pretty quickly lose the ability to load a new page if I'm browsing with IE or Firefox, and can regain it (temporarily) by disconnecting/reconnecting or letting the wireless manager troubleshoot, during which it resets the wireless adaptor. Doing a continuous ping of my router gives me anywhere from 30-70% data loss and lengthy round trips (I am currently one foot away from the router). Other (ancient!) computers work fine on my router; I have updated the router's firmware/reset it many times, etc). I didn't specifically go download a new driver for the wireless card, but going into its properties and having it search for an updated driver results in it reporting it already has the most up-to-date driver.
I spent a lot of late nights talking to Dell support, and their eventual fix (after a complete reinstall from the factory setting partition) was to set up my home network as a WEP, which I'm not happy with due to it's poor security compared to WPA2/WPA. This appeared to resolve the connectivity issue (why??). But I feel like I should be able to use WPA2 security with a brand-new laptop. So I changed it back to WPA2/WPA and tried installing all the critical updates that Windows Update could find, including SP1, and then looked at some continuous pings of various webpages and of my router itself.
Then I noticed my ping round trip time was awesome and they were 100% successful while my computer was plugged in with the power cord, but this unfailingly changed to reporting unsuccessful pings and having 1000ms round trips as soon as I disconnect the power. Seems like the on-battery power settings are starving the wireless card?
Also, I'm sure my initial intermittent connectivity (before the complete OS reinstall) was still occurring while plugged in with the power cord, so I'm not sure if the reinstall fixed some aspect of the problem, or whether the appearance of success while plugged in now is just temporary. Perhaps my card is just bad and I need a new one? I'm using the factory default power settings and the factory-installed wireless card (and I couldn't choose a different wireless card when I built my laptop)
I'm having problems connecting to the Internet using the wireless adaptor - it will connect initially but the connection is very very slow and then will eventually drop out and stop working.When I connect using an Ethernet cable, there are no problems whatsoever so I know it is not a service provider issue.I have updated the BIOS to A11 and all drivers are up to date. The wireless adaptor is Intel Centrino Wireless-N 1030. [code]
View 3 Replies View RelatedI just received a new xps 15 yesterday. After some long hours of research, I found that I need a different wireless adapter to pick up my routers 5.0GHz signal. The wireless adapter in my XPS right now is an Intel Cetrino Wireless-N 1000. I was wondering if I ordered an Intel Centrino Ultimate-N 6300, if it would be compatible with my new laptop, and if so, the ease of switching the two adapters.
View 14 Replies View RelatedI have a new laptop, Inspiron 15R 5520, which comes with Intel Centrino Advanced-N 2230 network card. It can only detect my wireless-G netowrk at home, but not wireless-N. I have another computer that can connect to my wireless-N, so network is working fine. I have updated the driver to the greatess and latest.
View 2 Replies View RelatedI have a Dell E1705 running windows 7 64 bit. I am attempting to upgrade my internal wireless adapter to the Intel Advanced N 6235 card.After installing the new wireless card and loading the latest drivers from Intel, the card is not working correctly. The problem is that my computer shows "no connections available". Device Manager says the card is installed properly and that it is working properly however there are no wireless connections for me to connect to including my own.
View 11 Replies View RelatedI have centrino N 6205 on my new Precision M6700...
Under both win 7 x64 (preinstalled dell) and 8 x64 on another hdd, there's no chance to have wifi working: I mean it does not work as normal wifi to connect to internet and it does not work not even a hotspot to let me connect for example my smarthphone to internet using wifi and a shared cable connection.The card seems to work, since I run a live fedora 18 distro linux from dvd and the wifi was able to connect pc to internet in less than one minute...
(of course I tried dell suggested drivers from download area, last updated intel drivers from intel website, etc etc...)...The wifi seemes to be correctly recognized in the pc but I get errors when I try to connect to router (I tried more than one routers that correctly work).
My system: D3ll Precision M6700| i7-3740QM| 32Gb 1866 mhz (4x8Gb)| 17.3" FHD IPS RGBLED 1920x1080| 8X DVD| K3000M| win8 x64 on Samsung 830 256gb| WD Black 500Gb 7200 rpm| 9 cells 97W| WIFI+BT Centrino N 6205 + Dell 380| QWERTY backlighted| psu 240w| warranty 3yr next business day|
I can´t connect to wifi because it simply doesn't read my wireless network card, I can only connect by an ethernet cable. I've tried to see if it appears in the device manager but it doesn't..
View 7 Replies View RelatedI have just fitted a centrino 6200 half mini card in an attempt to improve wireless conectivity and more so range
I assume that it would come up as new hardware found and then run the driver to get it to work. When fitted it doesnt appear in device manager and when trying to run driver the driver just runs then stops
Dell 8600 centrino intel pro wireless lan 2100 won't connect to netgear n150 wnr1000. Running 802.11b band it sees wireless network but won't connect. I have 2 other computers connected to network so it works.... I don't know if Netgear n150 is compatible with 802.11b band...
View 1 Replies View RelatedI'm having some connection problems with my new laptop (Dell XPS 14z).When I'm close to my router (D-Link DIR 635), the connection works just fine.When I'm a bit further from my router, I get a poor connection and a slow speed. I've tested 2 other laptops at the same spot, both of which have no problem with the connection.
View 2 Replies View RelatedI have an XPS L502x laptop with an Intel Centrino Advanced-N 6230 wireless card with the latest driver 15.6.0.0. For the past couple of weeks the strength of the signal as measured by the Intel proset tools goes from excellent to poor in the space of 60 seconds, back and forth. It seems to do this on all channels from 1 to 13. It definitely is affecting Internet performance. I have the security set at WPA-Personal in an attempt to try and stabilise the network. I have also been using iSSIDer to try and find the best channel since there are about 10 other wireless networks from other houses around me. I have a D-Link 645 router which is admittedly about 10 metres and 2 or 3 walls away. However, until a fortnight ago, the network was dead stable showing a strong signal (4 or 5 bars (-50). Now it is all over the place. Could it be a damaged card?
View 5 Replies View RelatedI have a problem with my laptop , i had an old intel centrino advanced-n 6200 and this was not working anymore.I manged to buy a intel centrino advanced-n 6235 instead of 6200 as i could not find it.But when i installed it and installed the drivers the pc is telling me that "This device cannot start. (Code 10)"
View 5 Replies View RelatedI own an Inspiron n5110 laptop(Dell) with an Intel(R) Centrino(R) Wireless-N 1030 wireless card. I use Windows 7 Ultimate 64-bit. I constantly drop internet connection, mainly when downloading and playing games. In the right bottom corner, where my wireless connection signal strenght is showed, I get an yellow triangle with '!' mark in it saying 'Limited access'. When troubleshooting, the only way to get an internet connection again, I get an message 'The default gateway is not available' and it says that it's fixed. after awhile I lose internet connection again and everything repeats. I figured out that it's not from my router or Internet Service Provider. I saw in the forums the option to exchange this card for the 6230 upgraded version but that is not a variant for me because in my country the technicians can at very damage the laptop.
View 7 Replies View RelatedJust bought and Alienware m17x, which has the Intel Centrino N2230 wireless card. The N2230 states that it is WIDI enabled but my computer shows nothing regarding wireless display anywhere in the search field. Don't know if there's compatibility issues with other components of my computer. If so the list of specs is as follows: CPU- 3rd gen Intel corei7 3630QM. GPU- 2GB GDDR5 NVidia GeForce GTX 660M. RAM- 16 GB Dual Channel DDR3 1600MHz. Wireless Card- Intel 2230 Wireless-N
View 3 Replies View RelatedI just purchased a used Latitude E5420. It looked like the seller did a fresh reinstall of Windows just before selling it to me. The non-internet applications are working fine, but it's not connecting to my home wireless router. I have a Buffalo WHR G-125. I tried pretty much every type of security type, but nothing worked, so I eventually disabled security and set up MAC filtering, after which I put in the MAC address for the laptop. That still didn't solve the problem.
It does connect to my neighbor's unsecured linksys network. Both the neighbor's network and mine are 802.11g
I went to Intel's website and installed the latest drivers for the network card, but that didn't work. I'm using the latest firmware on the router already.
Here are the specs for the laptop
Win 7 Professional 64-bit
Intel Core i5 2520M @ 2.50 Ghz
16 GB RAM
I've got a Centrino Advanced-N 6205 for Desktop wireless card and I'm trying to use the Intel My WiFi hotspot feature to connect my Xbox 360 Slim. The SSID shows up in the Xbox's networking settings, but after I enter the WPA passkey it fails to connect.
View 2 Replies View RelatedCan I install an Intel 6235 wireless card in my 14z (non XPS)?
View 2 Replies View RelatedMy friend has a dell d600 with the built in intel wireless card. All of a sudden his computer no longer shows that there is a wireless interface in the computer and he needs this computer for work. I'm thinking the driver may need to be reinstalled but I'm not entirely sure if it's that or a hardware error that's causing this malfunction.
View 3 Replies View RelatedFor some reason my card stopped working, I tried reinstalling the driver, fn + f2 (to activate my card from my keyboard), and a few others basic thing, nothing is showing up, where I am with other PC I can see at least 5 networks. my PC gets nothing,im running vista 32bitintel pro wireless 3945ABGdell inspiron laptop 6400I also tried a fixit microsoft tool for network, didnt work,Im on the net now using wired cable from my router, and its ok but I need my wireless on the road------------I have uninstalled reinstalled the driverI did a fresh format last weekI cant reset TCP IP. I get access denied, even in safe modeI did use many different use for removal of malware on my pc. im using avgchkdsk found no problems*** I did try alot of things, what can be doneWindows IP Configuration
Host Name . . . . . . . . . . . . : john-PCtopPrimary Dns Suffix . . . . . . . :Node Type . . . . . . . . . . . . : HybridIP Routing
[Code].....
I got a new laptop for Christmas that came with the Intel(R) Centrino(R) Wireless-N 2230 card that supports 802.11N. I am only seeing connection speeds of 1500mbps rather than the 300mbps that he DAP-1522 advertises.I found this on the d-link site but from what read on the Intel site about the card it supports the 40Mhz band. url...
View 3 Replies View RelatedI have a Lenovo T420 with a Intel Centrino Advanced-N 6205 wireless network card that causes me some headache. It randomly gets disconnected from my router (Zyxel P-2601HN-F1) and home network, works fine though if i using cable. Right after it gets disconnected it reconnects and works fine until it gets disconnected again. I have an HP laptop connected at the same time and no problems there.It works fine in the network in our office (work laptop). I tried our IT dept but they were clueless and told me I had to figure it out by myself, as it works in the office..
View 3 Replies View Relatedi have an Asus u56e that I recently bought a couple of moths ago. It has been a great computer until today when my wireless randomly disappeared for no reason. The wireless adapter has been disabled for no reason, and when I try to re-enable it, I can't seem to find it.
View 1 Replies View RelatedMine studio 1555 with intel core 2 duo P8700 [URL] processor and intel wifi 5100 agn card stopped connecting to router since last week. After searching a lot I found out that the Intel has stopped supporting 5100 for windows 8. Is there any way possible to use the same adapter with compatibility drivers on windows 8?? I have searched a lot but couldn't find much. All the new intel cards like "Intel Centrino Wireless-N 2200", n6300 are of 22nm while my processor is of 45nm. So will the newer card work with my processor.
View 1 Replies View RelatedCannot get my Intel WiFi Link 5300 wireless card to install properly on my my Latitude 6500 using XP SP3. I can go to the Intel website and download the latest driver but once everything has been downloaded and ran, then restarted the wireless icon says that my driver is not installed.
View 13 Replies View RelatedHow do I disable the power management feature that slows my NIC down when I am on battery power?
I have a dell e6500 with a Intel 82567LM Gigabit LAN card that always connects at 10Mbps when I plug in the ethernet cord when I am on battery power, I've tried using different routers (I have two gigabit routers and one 100 mbps router)... it still auto-negotiates at 10 mbps I've tried using different cat6 cables, it still auto-negotiates at 10 mbps.I've checked the drivers, I have 10.0.6.0, which is the latest from the support.dell.com website.
However, the minute I plug in the laptop, the NIC connects at the proper speed. Essentially, when the laptop is using battery power, the NIC decreases it's speed to 10 mbps. When I plug the laptop in, the speed jumps up to what it should be (either 100 mpbs or 1 Gbps, depending on which router I'm plugged in to).
So, how do I disable this feature? I want to connect at the maximum possible speed, regardless if I am plugged in or not.
Yesterday when I got home from college my computer randomly could not connect properly to my wireless modem. It tells me the SSID etc but when I connect to it, it becomes an unidentified network and has no internet connectivity. This problem only occurs on my laptop via wifi, wifi still works fine on other computers and my phone so I assume it is a problem on my laptops end. Also my laptop can connect to other wireless networks, ie my schools public network, and they work fine. I'm running windows 7 home premium.
View 8 Replies View Related