I can´t connect to wifi because it simply doesn't read my wireless network card, I can only connect by an ethernet cable. I've tried to see if it appears in the device manager but it doesn't..
View 7 Replies
I have just fitted a centrino 6200 half mini card in an attempt to improve wireless conectivity and more so range
I assume that it would come up as new hardware found and then run the driver to get it to work. When fitted it doesnt appear in device manager and when trying to run driver the driver just runs then stops
I have a new laptop, Inspiron 15R 5520, which comes with Intel Centrino Advanced-N 2230 network card. It can only detect my wireless-G netowrk at home, but not wireless-N. I have another computer that can connect to my wireless-N, so network is working fine. I have updated the driver to the greatess and latest.
View 2 Replies View RelatedI'm having some connection problems with my new laptop (Dell XPS 14z).When I'm close to my router (D-Link DIR 635), the connection works just fine.When I'm a bit further from my router, I get a poor connection and a slow speed. I've tested 2 other laptops at the same spot, both of which have no problem with the connection.
View 2 Replies View RelatedI have an XPS L502x laptop with an Intel Centrino Advanced-N 6230 wireless card with the latest driver 15.6.0.0. For the past couple of weeks the strength of the signal as measured by the Intel proset tools goes from excellent to poor in the space of 60 seconds, back and forth. It seems to do this on all channels from 1 to 13. It definitely is affecting Internet performance. I have the security set at WPA-Personal in an attempt to try and stabilise the network. I have also been using iSSIDer to try and find the best channel since there are about 10 other wireless networks from other houses around me. I have a D-Link 645 router which is admittedly about 10 metres and 2 or 3 walls away. However, until a fortnight ago, the network was dead stable showing a strong signal (4 or 5 bars (-50). Now it is all over the place. Could it be a damaged card?
View 5 Replies View RelatedI have a problem with my laptop , i had an old intel centrino advanced-n 6200 and this was not working anymore.I manged to buy a intel centrino advanced-n 6235 instead of 6200 as i could not find it.But when i installed it and installed the drivers the pc is telling me that "This device cannot start. (Code 10)"
View 5 Replies View Relatedwhat other cards are compatible with XPS 13 Ultrabook? Like so many people, I have been having a problem with my wifi when the computer is used a little far from the router, and thinking about buying a new wifi card for a replacement (which is silly, and I shouldn't have to do, given my computer is brand-new and cost more than £1000, I know... but I don't seem to have much choice). I've tried everything that has been suggested in the Dell forums, and elsewhere, including those on the Intel site. But nothing has improved my connection even a bit.I have Windows 8 (64-bit). And it currently has an 'Intel Centrino Advanced-N 6235' wifi card that came with it.
View 2 Replies View RelatedI just purchased a used Latitude E5420. It looked like the seller did a fresh reinstall of Windows just before selling it to me. The non-internet applications are working fine, but it's not connecting to my home wireless router. I have a Buffalo WHR G-125. I tried pretty much every type of security type, but nothing worked, so I eventually disabled security and set up MAC filtering, after which I put in the MAC address for the laptop. That still didn't solve the problem.
It does connect to my neighbor's unsecured linksys network. Both the neighbor's network and mine are 802.11g
I went to Intel's website and installed the latest drivers for the network card, but that didn't work. I'm using the latest firmware on the router already.
Here are the specs for the laptop
Win 7 Professional 64-bit
Intel Core i5 2520M @ 2.50 Ghz
16 GB RAM
I have a Dell E1705 running windows 7 64 bit. I am attempting to upgrade my internal wireless adapter to the Intel Advanced N 6235 card.After installing the new wireless card and loading the latest drivers from Intel, the card is not working correctly. The problem is that my computer shows "no connections available". Device Manager says the card is installed properly and that it is working properly however there are no wireless connections for me to connect to including my own.
View 11 Replies View RelatedI have a Lenovo T420 with a Intel Centrino Advanced-N 6205 wireless network card that causes me some headache. It randomly gets disconnected from my router (Zyxel P-2601HN-F1) and home network, works fine though if i using cable. Right after it gets disconnected it reconnects and works fine until it gets disconnected again. I have an HP laptop connected at the same time and no problems there.It works fine in the network in our office (work laptop). I tried our IT dept but they were clueless and told me I had to figure it out by myself, as it works in the office..
View 3 Replies View RelatedI've got a Centrino Advanced-N 6205 for Desktop wireless card and I'm trying to use the Intel My WiFi hotspot feature to connect my Xbox 360 Slim. The SSID shows up in the Xbox's networking settings, but after I enter the WPA passkey it fails to connect.
View 2 Replies View RelatedI purchased an XPS-17 Laptop from Dell, which was delivered last week. This system includes the Intel Centrino Advanced-N 6200 wireless network card. I also purchased the Netgear Push2TV HDTV wireless adapter on the advice of the Dell customer representative. The representative assured me that the two functions were compatible, and that all I needed to do was to have the network card search for new networks. Unfortunately the network card does not "see" the Netgear module, only the wireless LAN operating in my home. The Netgear Push2TV is connected to the TV via HDMI, and the TV displays the Push2TV setup screen indicating that it is waiting for a connection from a network card.
I have spoken with Dell Tech Support with no success. First of all the Tech Support representative had no knowledge of the wireless TV display capability, let alone the Netgear Push2TV device, thus did not know how to diagnose the situation, neither did her supervisor. I authorized remote access into the computer and they tried all they knew how to do with no success. Finally, after 2 hours, I was told that Dell was aware of an incompatibility issue between the two devices, and that I should just wait until it was resolved by Dell and/or Netgear in "one or two days". After hanging up, I realized that I had not been given a Case Number, thus had no record of the call.I have been checking the Drivers/Downloads site daily, but find no new releases that are not already installed on the computer.
I have an XPS L502x laptop with an Intel Centrino Advanced-N 6230 wireless card. For the past couple of weeks the strength of the signal as measured by the Intel proset tools goes from excellent to poor in the space of 60 seconds, back and forth. It seems to do this on all channels from 1 to 13. It definitely is affecting Internet performance. I have the security set at WPA-Personal in an attempt to try and stabilise the network. I have also been using iSSIDer to try and find the best channel since there are about 10 other wireless networks from other houses around me. I have a D-Link 645 router which is admittedly about 10 metres and 2 or 3 walls away. However, until a fortnight ago, the network was dead stable showing a strong signal (4 or 5 bars (-50). Now it is all over the place. Could it be a damaged card?
View 1 Replies View RelatedI have centrino N 6205 on my new Precision M6700...
Under both win 7 x64 (preinstalled dell) and 8 x64 on another hdd, there's no chance to have wifi working: I mean it does not work as normal wifi to connect to internet and it does not work not even a hotspot to let me connect for example my smarthphone to internet using wifi and a shared cable connection.The card seems to work, since I run a live fedora 18 distro linux from dvd and the wifi was able to connect pc to internet in less than one minute...
(of course I tried dell suggested drivers from download area, last updated intel drivers from intel website, etc etc...)...The wifi seemes to be correctly recognized in the pc but I get errors when I try to connect to router (I tried more than one routers that correctly work).
My system: D3ll Precision M6700| i7-3740QM| 32Gb 1866 mhz (4x8Gb)| 17.3" FHD IPS RGBLED 1920x1080| 8X DVD| K3000M| win8 x64 on Samsung 830 256gb| WD Black 500Gb 7200 rpm| 9 cells 97W| WIFI+BT Centrino N 6205 + Dell 380| QWERTY backlighted| psu 240w| warranty 3yr next business day|
I have just got my new xps 17 and opted for the 6230, It only gets to 20 meg download speed, I can insert my old usb N adaptor and get the full 50 meg. I was on the phone for 2 hours last night with Dell, they had remote access and tried lots of things to improve the problem.
Finally once they saw that my old usb adaptor was much faster, they said a technician would call me back today betweek 12pm and 1pm or 4.30pm.
I just received a new xps 15 yesterday. After some long hours of research, I found that I need a different wireless adapter to pick up my routers 5.0GHz signal. The wireless adapter in my XPS right now is an Intel Cetrino Wireless-N 1000. I was wondering if I ordered an Intel Centrino Ultimate-N 6300, if it would be compatible with my new laptop, and if so, the ease of switching the two adapters.
View 14 Replies View RelatedI have just taken delivery of a new Inspiron N5110 with an Intel Centrino N-1030 wifi card. I also have two dual band routers (LInksys WRT600N) in different locations in the house.
My problem is that the laptop is detecting my routers Wireless-G signals but NOT the Wireless-N signals. I have checked to ensure that the N-1030 card has 802.11n Mode set to Enabled and have also tried both setting under "802.11n Channel Width for band 2.4" (i.e. Auto and 20 MHz Only) with no success.
My routers are configured with the Wireless-G signal only on 2.4 GHz and Wireless-N only on 5 GHz. I found this to be the best setting to avoid interference from neighbors wifi and cordless phones and have been happily using Wireless-N with my other Dell laptop with no problems (XPS M1530 with Intel 4965agn wireless card).Does the N-1030 card not work with 5 GHz Wireless-N?
The wireless on my laptop keeps dropping out. When I first got it it was fine, but after a while I started experiencing problems on every wireless network I connected to. Most of the time it would connect, but after around 10 minutes or so, the connection would drop out and the wireless card has to be "reset" so I can connect again. Otherwise I have a little yellow triangle over my network signal strength bars. I've updated to the latest drivers (14.2.0.10) but it was no luck.
This happens with every wireless network and I know it's not the network because my old Vostro 1500 is running just dandy on all of them.
Just bought and Alienware m17x, which has the Intel Centrino N2230 wireless card. The N2230 states that it is WIDI enabled but my computer shows nothing regarding wireless display anywhere in the search field. Don't know if there's compatibility issues with other components of my computer. If so the list of specs is as follows: CPU- 3rd gen Intel corei7 3630QM. GPU- 2GB GDDR5 NVidia GeForce GTX 660M. RAM- 16 GB Dual Channel DDR3 1600MHz. Wireless Card- Intel 2230 Wireless-N
View 3 Replies View RelatedMy laptop has Intel(R) Centrino(R) Wireless-N 1030 internet card but the computer can not connect to the modem properly, the speed is always not the speed that I purchased
View 1 Replies View RelatedCurrently using intel 5100 & 6200 client cards on multiple driver versions. WiSM is 7.0.116. APs are 1250 and 1260 series. Citrix is setup to send server-side keepalives for session reliability. Randomly, several times a day the client will get disconnected from the Citrix application session but maintain connectivity to the AP and other applications continue to work. Traces show the server-side keepalive reach the controller but are delayed from controller to client by 5-6 seconds. Just enough time for the Citrix server to timeout and tear down to session. Additional testing shows the delay most likely occurs somewhere from controller to AP. It occurs on multiple controllers on multiple campuses.
We have Dell/Broadcom clients that don't experience the problem. The only commonality seems to be the Intel cards. CCX? I know Intel has a special relationship with Cisco regarding CCX and have developed features not available on other cards. Tried disabling power save and other CCX features but hasn't solved the issue.
Dell 8600 centrino intel pro wireless lan 2100 won't connect to netgear n150 wnr1000. Running 802.11b band it sees wireless network but won't connect. I have 2 other computers connected to network so it works.... I don't know if Netgear n150 is compatible with 802.11b band...
View 1 Replies View RelatedI have an ASUS u56e laptop running Win7 Pro that I bought in Aug 2011. Unfortunately my problems started when I was working in East Timor and could not take it anywhere except the IT department where I worked. It is true that for a while I was using the LAN at work and also at my hotel where numerous ISPs were used at various points in time.
I have progressively lost almost total use of the wireless capacity of the machine and this is regardless of where I am using the computer (country, state, public or private networks). Very rarely will I have access and then not for long. When it is not working I will get a message saying that a network adapter cannot be found.
I have updated the driver software and experimented with the power settings. I have also uninstalled an ASUS utility that I read might have been a problem. About the only thing that sometimes works is to disable the network adapter, shut down, and then restart the computer. But not for long.
There is WiMax capability that came with the computer, which I bought at Best Buy. Based on IT advice I have made sure that WiMax is off but the wifi button indicates 'on.' When I am having problems though, I cannot see the wifi button.
I am using Windows Firewall and Webroot SecureAnywhere v.8.02.109. At device manager I see for network adapters: Intel(R) Centrino(R) WiMax 6150 and Intel(R)Centrino(R) WirelessN6150. There is also an entry above for a 6150 Function Driver.
I have attached an image of the ipconfig from the ASUS.
I got a new laptop for Christmas that came with the Intel(R) Centrino(R) Wireless-N 2230 card that supports 802.11N. I am only seeing connection speeds of 1500mbps rather than the 300mbps that he DAP-1522 advertises.I found this on the d-link site but from what read on the Intel site about the card it supports the 40Mhz band. url...
View 3 Replies View RelatedThe problem is that it always stays around 121-150mbps and sometimes 270mbps(beside router). here is my wireless settings on my router
router setting 1: [URL]
router setting 2: [URL]
network card setting:
802.11n channel width:auto
802.11n mode:Enabled
Ad-hoc channel:11
Fat channel intolerant:Disabled
Roaming aggressiveness :Medium
Throughput enhancement:Disabled
Transmit power:Highest
Wireless mode:802.11a/b/g
i have an Asus u56e that I recently bought a couple of moths ago. It has been a great computer until today when my wireless randomly disappeared for no reason. The wireless adapter has been disabled for no reason, and when I try to re-enable it, I can't seem to find it.
View 1 Replies View RelatedLooking for some old firmware, version 3.2.1.3, any link to where it is?
View 5 Replies View RelatedI have intel centrino n 2230 wireless card in my alienware M17X-R4. When I search for available WLANs I can see all 2.4 GHz networks but none 5 GHz.
I have Netgear WNDR3800 AP running openwrt backfire 10.03.1
settings for the AP are:
mode:802.11 a+n
HT mode: 20 Mhz
Channel: 40 (5.200 GHz)
i tried several config alternatives - no joy
i updated the driver of the intel wifi card to the latest - no joy.
I have meny concerns but one is intel Centrino Wireless 2230 2X2 bgn + Bluetooth a not so reliable wirless hookup?
View 1 Replies View RelatedI have a Wi-Fi connection problem on my Dell Inspiron 17R SE 7720 with Intel Centrino Wireless-N 2230. Every time after I log in to Windows I can’t use internet for about 5 to 15 minutes. After that time everything seems almost OK. During this time there’s yellow exclamation mark on my connection icon (saying that there’s no internet connection) just for a few seconds, than it dissapears and apparently internet connection is OK (signal strength is very good the whole time), but during this 5-15 minutes downtime I can’t use internet. Websites by domains don’t respond, neither pings do, but when I ping eg. google.com by its IP it responds quickly, so I thought it’s a DNS issue.Connection settings are automatic. DNS servers (resolved automatically) of my cable ISP respond OK when I ping them during the downtime. So just to check, I’ve set manually DNS servers to Google public DNS servers (both IPv4 and IPv6). It didn’t work.
I don’t use antivirus software other than Windows Defender. The issue occurs with and without firewall. I have the most recent both BIOS (A11) and Wi-Fi drivers (15.3.1.2 downloaded from Intel site). My system: Windows 7 Home Premium PL 64bit. I keep the system updated with Windows Updates. The issue occurs when Windows manages my connection and also when I have Intel PROSet/Wireless WiFi software installed.I don’t allow Window to turn off the WiFi card (device’s energy settings). I’ve set Roaming Aggressiveness to 5. Highest and Ad Hoc Channel 802.11 b/g to 11 (I’ve seen such a piece of advice somewhere). Maybe it’s something with compatibility with the router, by the issue doesn’t occur of any other device in my network (Android phones, Kindle, iPad). I’ve got Cisco EPC3925 from my cable ISP. They didn’t give me the password, so for now I can’t change its settings.
Its “about” page reads:Cisco EPC3925 EuroDocsis 3.0 2-PORT Voice Gateway Model: Cisco EPC3925Vendor: CiscoHardware Revision: 1.0Bootloader Revision: 2.3.0_R1Current Software Revision: epc3925-E15-13-v302r125554-120725cFirmware Name: epc3925-E15-13-v302r125554-120725c.binFirmware Build Time: Jul 31 12:51:23 2012Cable Modem Status:OperationalWireless Network: EnableCable Modem State:DOCSIS Downstream Scanning: CompletedDOCSIS Ranging: CompletedDOCSIS DHCP: CompletedDOCSIS TFTP:CompletedDOCSIS Data Reg Complete: CompletedDOCSIS Privacy: DisabledDownstream Channels: Power Level: Signal to Noise Ratio:Channel 1: 5.9 dBmV 42.7 dBChannel 2: 6.7 dBmV 42.3 dBChannel 3: 6.4 dBmV 42.5 dBChannel 4: 6.2 dBmV 42.5 dBChannel 5: 6.0 dBmV 42.0 dBChannel 6: 5.5 dBmV 42.5 dBChannel 7: 0.0 dBmV 0.0 dBChannel 8: 0.0 dBmV 0.0 dBUpstream Channels Power Level:Channel 1: 52.5 dBmVChannel 2: 0.0 dBmVChannel 3: 0.0 dBmVChannel 4: 0.0 dBmV
I saw some other mentions online of intermittent internet connectivity using the factory-installed Intel Centrino wireless-N 1030 card on various new Dell computers running Windows 7, but didn't see any resolution to the problem.
I can connect directly to my router via an ethernet cord, but trying to use the wireless card gives me intermittent connectivity. I will pretty quickly lose the ability to load a new page if I'm browsing with IE or Firefox, and can regain it (temporarily) by disconnecting/reconnecting or letting the wireless manager troubleshoot, during which it resets the wireless adaptor. Doing a continuous ping of my router gives me anywhere from 30-70% data loss and lengthy round trips (I am currently one foot away from the router). Other (ancient!) computers work fine on my router; I have updated the router's firmware/reset it many times, etc). I didn't specifically go download a new driver for the wireless card, but going into its properties and having it search for an updated driver results in it reporting it already has the most up-to-date driver.
I spent a lot of late nights talking to Dell support, and their eventual fix (after a complete reinstall from the factory setting partition) was to set up my home network as a WEP, which I'm not happy with due to it's poor security compared to WPA2/WPA. This appeared to resolve the connectivity issue (why??). But I feel like I should be able to use WPA2 security with a brand-new laptop. So I changed it back to WPA2/WPA and tried installing all the critical updates that Windows Update could find, including SP1, and then looked at some continuous pings of various webpages and of my router itself.
Then I noticed my ping round trip time was awesome and they were 100% successful while my computer was plugged in with the power cord, but this unfailingly changed to reporting unsuccessful pings and having 1000ms round trips as soon as I disconnect the power. Seems like the on-battery power settings are starving the wireless card?
Also, I'm sure my initial intermittent connectivity (before the complete OS reinstall) was still occurring while plugged in with the power cord, so I'm not sure if the reinstall fixed some aspect of the problem, or whether the appearance of success while plugged in now is just temporary. Perhaps my card is just bad and I need a new one? I'm using the factory default power settings and the factory-installed wireless card (and I couldn't choose a different wireless card when I built my laptop)
Well I'm typing from my tablet right now because for the 20th+ time, the Centrino 1030 card on my Vostro 3450 isn't connecting to hotel's wireless. Other places I have encountered it to have connection problems is colleges, universities, coffee shops, etc. It is also slow as molasses in my home too.
I have read other posts indicating similar problems without resolutions on the Vostro 3450. I am planning on replacing it with the BEST WLAN card there is. It seems a bit labor intensive from the service manual but doable. Has there been any "for sure" fix with the 1030 card?
The 1030 card is so incredibly bad that I am able to get 3/5 bars on my home network being outside while my Vostro can't even pick it up.
I'm having problems connecting to the Internet using the wireless adaptor - it will connect initially but the connection is very very slow and then will eventually drop out and stop working.When I connect using an Ethernet cable, there are no problems whatsoever so I know it is not a service provider issue.I have updated the BIOS to A11 and all drivers are up to date. The wireless adaptor is Intel Centrino Wireless-N 1030. [code]
View 3 Replies View Related
