Cisco Switching/Routing :: 3560 - Vlans Unable To Access Internet
Feb 23, 2012I have configured vlans in 3560G switch but vlans notable to accessing Internet
View 6 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 3560 Extend VLANs Out To Remote Access Clients
Mar 31, 2013I am not sure if what I am trying to accomplish is possible. On my internal network I have the following VLANs setup (102, 104, 106) and they map one to one to a subnet (ie: 102 = 192.168.102.0/23, 104 = 192.168.104.0/24, etc).All interVLAN routing is done on a 3560 via vlan SVI. Connected to the 3560 via a routed port is a ASA 5510. The routed port has IP 192.168.100.1 and the ASA interface on the other side of that routed port has IP 192.168.100.2. I use 802.1x on the wired network to assign users (based on their department) into a specific VLAN. I want to extend this concept to Remote VPN access. Therefore I setup multiple Group Policies (policy is applied based on an LDAP attribute) where each policy defines a different DHCP scope. This has successfully allowed me to login wtih different users who get assigned to different Group policies and they obtain the correct DHCP IP address from the internal DHCP server (ie: an engineering person logins remotely and gets an IP in 192.168.102.0 range). However the issue (and as I was planning this out I knew this would come up) is that traffic can be routed out from the VPN client to its destination but there is no return path.
View 3 Replies View RelatedCisco Switching/Routing :: SF300-24p / Access Internet On VLANs
Mar 16, 2013i have one SF300-24p switch where i setup some Vlans and echolife hg8245 ONT router to access internet. the diagram is the following
VLAN1 (Subnet of users) -----> Switch SF300-24p
VLAN2 (Subnet of users) -----> Switch SF300-24p
VLAN3 (HG8245) -----> Switch SF300-24p
VLAN4 (Servers) -----> Switch SF300-24p
i want to control access to internet on VLAN1 and VLAN2 (access on VLAN3), while providing access to VLAN4.My problem is in connecting to internet, i can't find a way to "route back traffic to VLANs 1 and 2 since HG8245 don't seem to provide proper static routing ON LAN interface. Maybe without resorting to changing the HG8245 router ?
Cisco Switching/Routing :: 3550 / VLans Not Able To Access Internet?
Jun 12, 2012We have cisco 3550 switch i have configured 3 vlans in this switch vlans are not able to accessing internet
View 7 Replies View RelatedCisco Switching/Routing :: SG300 No Internet Access On New VLANs
Apr 16, 2012I am trying to setup VLAN's in the company I work for and I am almost there but missing the part when the internet works.I have an SG300 as a L3 Router IP 192.168.0.93.I have created VLAN20 and VLAN40 Assigned VLAN20 192.168.2.1 and VLAN40 192.168.4.1
The static routes have been created and a default router going to the Sonicwall firewall at 192.168.0.1.Port 24 is configured as Untagged VLAN1, Untagged VLAN20 and VLAN40 in trunk mode and going to the Sonicwall NSA 2400. [code]
Working to move all 192.168.0.x network off of VLAN1 and move it a management switch.I have DHCP helper on pointing to the DHCP server.Both VLAN's once the DHCP server is configured to Gateway 192.168.0.93 can get an IP from the correct subnet either 192.168.2.x or 192.168.4.x
All PC's are getting a GW IP of 192.168.2.1 pr 192.168.4.1.All test PC's on both VLAN's can ping each other and any server with the correct GW.When I try to ping google.com or open a web page and try google.com it times out.
Cisco Switching/Routing :: 3560 / Creating Extended VLans And Subinterface?
Jan 24, 2013We have a 3560 switch running IOS universalk9-mz.150-1.SE3.bin.Recently, we saw two problems with this switch:-
1. if we try to enable subinterface on any routed interface , for eg. gig1/1, it says invalid input detected. It doesnt accept encapsulation command also. Following was done to enable subinterface:
int gig1/1
no ip address
int gig1/1.2000
ip address 1.1.1.1
under the gi1/1.2000 subinterface, it doesnt present the option of ip address.
2. we created a layer 2 vlan 2000 like: vlan 2000 When we do an exit after creating this vlan , it gives following error:-
%SW_VLAN-4-VLAN_CREATE_FAIL: Failed to create VLANs 2000: extended VLAN(s) not allowed in current VTP mode
Cisco Switching/Routing :: 3560 / STP Loop Guard Blocking Vlans?
Mar 24, 2013I have a strange issue where spanning-tree is blocking vlans through a mesh network.Here is my set up.
2-Cisco 3560's that have two trunk ports set with do1q and a native vlan of 2. I'm allowing a client vlan (2) and a voice vlan (103) to come over the trunk. They have a native vlan of 2 so the mesh APs can get an address through DHCP. Spanning-tree loop guard is also enabled.
When connected to the mesh network, the voice vlan is being blocked by spanning-tree. I get the following erros:
000129: *Feb 28 19:24:58.289 EST: %SPANTREE-2-LOOPGUARD_BLOCK: Loop guard blocking port FastEthernet0/1 on VLAN0103.000130: *Feb 28 19:24:58.448 EST: %SPANTREE-2-LOOPGUARD_UNBLOCK: Loop guard unblocking port FastEthernet0/1 on VLAN0103.
Eventually the loop is cleared and the port is set back to a forwarding state from a blocking state. I don't want to disabled spanning-tree loopguard since I don't want to create a loop. The mesh network is supposed to act as a P2P connection between two switches. As a test I disconnected the APs from their trunk ports. I then used a cross over cable to connect the switches and no spanning tree loops occured. The mesh doesn't have STP enabled on it and should just be acting as an over-the-air connection from one switch to another.
Cisco Switching/Routing :: Sharing Internet Access Through A 3550 With 2 Vlans?
Apr 27, 2013They have a locked Cisco Router which is from the ISP and its confed on a fa 0/0 interface to share Internet access on the network. The ip on that interface is 195.198.11.217 255.255.255.252 and i tried it with a PC (set my personal ip to .218 and entered their dns info (195.67.199.27) and it is working. The question is now. My friend found a 3550 laying around and since the ISP wont let them conf their router he wants to use the 3550 to create 2 vlans with internet access and without access to eachother. Vlan 10 for the desktops and Vlan 20 for the wireless (Moving on to some netgear wireless switches) How would you configure the 3550 for this to work?
View 23 Replies View RelatedCisco Switching/Routing :: 2950 / Vlans And Internet Access Sharing?
Apr 5, 2013i am trying to set up a cisco 2950 with a vlan to seperate all of the pos machines on the network (4 of them) from all other machnes in the building (3 hard wired and wi-fi). i was going to use vlan 1 as a trunk to allow internet access to go from fa0/1 to both vlans (vlan 10 and vlan 20). i have read things about the acl having an explicit deny at the end, so i'm thinking that is my problem. i am testing it at my house before deploying it to the network. i have 1 laptop setup with an ip of 192.168.0.50, and the other is .60. my router is 192.168.0.1. i have the ethernet from the router plugged into fa0/1, the 1st laptop on fa0/2 and the other at fa0/3. before i set the vlans up, i checked the communication by just plugging them in and trying to ping, they could both ping each other, the router and 8.8.8.8. when i finished setting up the test vlans, they could not ping each other(what i wanted) and laptop 1 can ping the router, and 8.8.8.8. laptop 2 cannot ping anything.
the only thing i did was create vlan 10 and 20, set port fa0/2 to vlan 10 and no sh, fa03 to vlan 20 and no sh, fa0/1 to vlan 1 and no sh. then i did switchport mode trunk on fa0/1, and switchport native vlan 1. this seems to be how i was supposed to do it, but it's been a while since i have worked with switches. i'm sure it's simple, but after searching the internet and poring over my cisco books for 5 hours, it is turning out not to be the case. here are some details:
greenhouse#sh int fa0/1 switchport
Name: Fa0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
[code]...
Cisco Switching/Routing :: Internet Access For 3550 Switch VLANs?
Feb 22, 2012I have a small cisco switch cluster (seven different 2924, 3524cisco switches) with 3550 as a cluster control which does all the inter vlan routing that works fine.
This cluster is in semi production PBX interop testing lab. This is a closed network without internet access and not connected to our corporate network.However now I have to add this capability so some equipment in the lab can get Microsoft updates over the internet.
I've created a port on a 3550 (fa0/19) and connected it to another network that has internet access. It picked an ip address and when I'm logged in to the 3550 I can ping hosts on the outside network. However I can't ping any hosts on that network from any hosts that are connected to my vlans.I've tried a few different things, but still can't make it to work.
Here is a short version of my 3550 configuration:
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime
no service password-encryption
[code]....
Cisco Switching/Routing :: 3845 / 3560 - Bridging Multiple VLANs Over Router
Aug 27, 2007We have a customer that is relocating thier headquarters. They have a temporary requirement to bridge multiple vlans or a router T3 link to the new location as they cannot change the IP subnets. Setup is 3560 switch connecting to a 3845 then T3 to remote 3845 and 3560. I need to bridge multiple VLANs. I have seen a good example on how to do it over sonet but I don't see how to translate that to an HDLC or Frame Relay encapsulation for the T3 Link.
View 5 Replies View RelatedCisco Switching/Routing :: Catalyst 3560 SVI - VMs Cannot Access Internet
Aug 12, 2012I have 5 SVIs configured for VLAN Interfaces 121-125 for my vSphere environment.
All VMs can ping IPs on all the VLANs (VMs on VLAN 124 can ping VMs on VLAN121)
All VMs, except those on VLAN 124, can access the Internet or even ping my router IP.
If I change one of the VLAN 124 VMs to use a different VLAN, and update the addressing appropriately, it can access the Internet.
The problem is exhibited with Windows and Linux VMs. So, I believe something in my switch setup is the problem with VLAN 124 in particular.
If i do a show vlan brief, VLAN 124 is listed.
If I do a show ip int brief, VLAN 124 is listed as upup. I also tried to shut o shut the VLAN 124 interface.
Only one specific VLAN has connectivity problems?
My topology is Catalyst 3560 to home router to Internet.
Here is my IOS image: c3560-ipservicesk9-mz.122-55.SE6.bin
Here is my show run output:
3560_02#sh run
Building configuration...
[Code].....
Cisco Switching/Routing :: 2911 / 2960S - Multiple VLANs With Different Internet Access
Feb 17, 2013We need to give differentiated internet access to three VLANs. Each one of this VLANs is used for totally different purposes, so traffic between the VLANs is not allowed. Each VLAN has its own internet access provided for the data center using one fast ethernet connection.
We're thinking about using cisco 2911 for Internet access, VPN and firewall. I suppose that best option for VLANs is using Catalyst 2960S or a swithing module for the 2911, but these two options are too expensive for us. We're thinking about using swtiches from the SB series (maybe a SG-200).
We're totaly newbies to VLANs so we have many doubts. This are our questions:
1) The 2911 has three on board ethernet interfaces; we have three VLANs and three internet connections, so we need to use HWICs to get three more ethernet ports. That's right?
2) We need three HWICs or there is some kind of HWIC with more that one ethernet interface?
3) The routing solution is to assign static routes in the 2911 for each interface connected to a VLAN through a 2911's interface connected to internet?
4) Simply connecting three different router interfaces with three different switch ports, each one of them assigned to one of the three different VLAN, are we going to get internet access for all devices in those VLANs? or do we need to configure something else like trunking, VSIs...?
5) Can we achieve our goals using the SG-200 switch?
6) We have the chance to use older routers, is this possible? We're specially interested in knowing if a 1841 or a 2801 router could be used for this setup.
7) This is not a production environment so we can use refurbished equipment.
Cisco Switching/Routing :: Block Traffic Between Two Vlans On Cat3560C - Internet Access?
Aug 3, 2012I have a Cisco C3560CG which is running C3560c405ex-UNIVERSALK9-M), Version 12.2(55)EX2.The switch has vlan 1 and vlan 50 configured, vlan 50 should have access to a limited number of host in vlan 1.The following acl has been applied on the inbound to vlan 50:
10 permit tcp 10.16.30.0 0.0.0.255 host 192.168.15.243 eq 137 138 139 445
20 permit udp 10.16.30.0 0.0.0.255 host 192.168.15.243 eq netbios-ns netbios-dgm netbios-ss 445
25 permit icmp 10.16.30.0 0.0.0.255 host 192.168.1.243
26 permit ip 10.16.30.0 0.0.0.255 host 10.16.30.254
30 permit ip 10.16.30.0 0.0.0.255 host 192.168.15.254
[code]....
I sure the above would work, but for some reason some of the packet counter are not incrementing but the traffic is being blocked. But I would like to see the counter increment.Also I have that I may beed to use VACL wouls this be the case?
Cisco Switching/Routing :: 3560 - Unable To Perform VLAN Routing
Apr 28, 2012We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing. We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.
View 17 Replies View RelatedCisco Switching/Routing :: 3560 - Unable To See Entry For Switch
Oct 30, 2011I have configured a new switch 3560 switch and connected to 4500 switch and formed a trunk connectivity.Now the issue i am facing is when i do a SH CDP NEIGHBOUR from 3560 switch i am able so see 4500 swries switch but at the same time when i do SH CDP NEIGHBOUR form 4500 series switch i am not able to see the entry for 3560 switch.But i am able to telnet the new switch with out any issues
View 11 Replies View RelatedCisco Switching/Routing :: AIR-SAP2602I-E-K9 Unable To Access Internet
Feb 25, 2013I have installed the six new WAP with model Cisco AIR-SAP2602I-E-K9, and we have two SSID for the new WAPs. When the users are connected to this WAP they can able to access the intranet but not able to access the internet. What could be the problem? I have checked and verify that they can able ping to the IP address of google from the CMD but when try from internet explorer they are fail (both with www.google.com & with IP address of google).
View 2 Replies View RelatedCisco Switching/Routing :: SG-300 Vlan Unable To Access Internet
Apr 1, 2013I am using a Cisco SG-300 28 port switch in layer 3 mode as my default gateway for all my devices. I have two vlans on the switch, vlan 1 and vlan 4. Both are pulling valid IP addresses in their scope from the DHCP server, and both have valid DNS settings. I set a static route to the Internet on the switch to our firewall (192.168.5.254). All devices connected to vlan 1 are able to access the Internet, however all devices connected to vlan 4 cannot get past the switch. A tracert from one of these devices shows it hits the switch as the gateway, but gets no further. [code]
View 4 Replies View RelatedCisco 3560 VLANs And Inter-VLAN Routing
Sep 29, 2011I have no router inplace that can do trunking (5505 basic license )I have 2 VLANS 10 Data 20 voice I have given both VALNs IPs lets say
-VLAN10 192.168.1.1
-VLAN20 192.168.2.1
Enabled IP routing and set the router as the gateway of last resort.Now becuase the L3 switchis doing the routing I have had to set the default gateway as the VLAN IPs. So PCs on VLAN10 get a gateway of 192.168.1.1 and phones on VLAN20 get a gateway of 192.168.2.1
Any real downside to having the 3560 doing the VLAN routing, is this the "correct "way to do things in the event I don't have a trunkable router?
Cisco Switching/Routing :: 800 / Use ASA To Configure All The Vlans And Intervlan Routing And Access Lists?
Jul 4, 2012upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies View RelatedCisco Switching/Routing :: 1921 Routing Access From Mixed IP Ranges Between VLANS
Jan 23, 2013I have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
Cisco Switching/Routing :: 3560 - Access List On InterVLan Routing
Dec 11, 2012I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B
Network A. 10.0.12.0/24
Network B 10.0.24.0/24
The configuration is
interface Vlan1
description Data VLAN
[Code].....
Cisco Switching/Routing :: QOS For 3560 Access Switch
Nov 28, 2011we have a class based qos scheme (see attached file) on our 4500 series access switches and we have a access 3560-48 switch runing IOS Version 12.2(44)SE3 my question is can I use the same QOS scheme for the 3560 switch?
View 3 Replies View RelatedCisco Switching/Routing :: 2900 Will Work As Access Port For More Than Vlans
Mar 27, 2012I have came across this topic, and I am wondering if this images can be uploaded to any 2900 series switches or not, and if this will work as access port for more than vlans. URL...
View 2 Replies View RelatedCisco Switching/Routing :: 6509 / Restrict Access To Sensitive VLANs?
Jun 4, 2012We have a network of 30 VLANS and currently all the vlans have access to everything. We are using Cisco 6509 switch for Layer3 routing.I would like to prevent some VLANs accessing the server VLANs. How can i resrict access to the server VLANs? Do i need to implement access-lists on the 6500 switch? or do i need to create VLANS on the firewall so that all traffic i filtered?
View 3 Replies View RelatedCisco Switching/Routing :: 3650 / 5505 / 1252 - Access Between VLANs
Dec 22, 2012I have set up a scenario for a small business and have some questions about how to manage the access between the VLANs. Is there is a better / another way to do it. See the attached picture for the topology / info.
My question is:
My switches is set up with x numbers of VLANs and a routed port (no switch port) to the ASA for internet connectivity. How is the best (or only??) way to manage the access between the VLANs? Is it ACL's on the switch?
And by "managing access" I mean VLAN 50 (public WiFi) only have access to the internet, only management servers have access to management VLAN, Client VLAN only have RDP access to server VLAN and so on. Is there any way to do this in the ASA (or add another (gigabit) router to the topology)) or it the only way to have lots of ACL's on the switch itself? I have thought about "router on a stick", but then I imagine there will be a bottleneck between the switch and the ASA?
(Equipment is 2 x 3650G, ASA5505, AP1252 - see attached file).
Cisco Switching/Routing :: 3750x - Denying VLAN Access To Other VLANs
Mar 18, 2013I've got a 3750x stack set up as my core switch (only a small-ish environment) - I'm shortly going to be deploying an enterprise wireless network with Corporate and Guest SSID's. I'm going to be putting all traffic from the Guest SSID in VLAN 244, and don't want it to have access to any of the other VLANs (1 (Legacy Eqpt), 4, 8, 12, 16, 20, 24, 28, 32, 248 & 252).
IP ranges for all the main VLANs are:
1: 10.0.0.x/22
4: 10.0.4.x/22
8: 10.0.8.x/22
12: 10.0.12.x/22
16: 10.0.16.x/22 etc etc (you get the pattern)
I'll probably give Guest traffic (VLAN 248) the IP range 192.168.10.x/22 (not because I NEED that many addresses, but it's easier for everyone to remember/understand if I keep the subnet masks the same all round). However I also have a CCTV VLAN (252) which already has the range 192.168.0.x/24, which some people in other VLANs WILL need access to.
So my question is: What is the syntax for the ACL on my 3750x (IP base - 15.0.2) to prevent traffic from VLAN 244 gaining access to any of my other VLANs. I'm making a broad assumption here that a layer 3 switch is perfectly capable of supporting that function? I need ALL the syntax for setting up ACL's - I've never done it before
My gateway device by the way is 10.0.4.1, and I do have inter-VLAN routing set up on the core switch (obviously).
Cisco Switching/Routing :: 3560 - Randomly Can't Get Access To Any Resources
Jan 16, 2013I have a couple of users who randomly can't get access to any resources. The port they connect to doesn't have port security, the have an IP phone and PC. IP phone is fine since it's always on the same port. There PC get's an IP from DHCP (DHCP is on a windows server) but they can't ping any devices nor can I ping the PC from the switch. I checked if there were any mac access filters applied on the switch (and there aren't any). The log doesn't show any events on the ports in question so I don't know if the switch is going or there is a config issue some. Doesn't happen to all users, just 1 or 2.v
View 11 Replies View RelatedCisco Switching/Routing :: 3560 - Access Switch / LED Blinking
Jan 2, 2013My access switches LED is start blinking very fast suddenly,it has single up link from the Core switch.access switch is 3560.what can be the possible problem.
View 1 Replies View RelatedCisco Switching/Routing :: 6509 Switch To Restrict Access To Sensitive Vlans
Feb 20, 2012We have a network of 30 VLANS and currently all the vlans have access to everything. We are using Cisco 6509 switch for Layer3 routing.I would like to prevent some VLANs accessing the server VLANs. How can I restrict access to the server VLANs?Do i need to implement access-lists on the 6500 switch? or do i need to create VLANS on the firewall so that all traffic i filtered ?
View 9 Replies View RelatedCisco Switching/Routing :: SG500 Vlans Cannot Reach Internet
May 20, 2013PCs --> SG500(4 vlans) --> rv042 --> Internet..vlan 1 is able to reach the internet..vlan 2-4 cannot reach the internet, but can reach vlan 1.
View 2 Replies View RelatedCisco Switching/Routing :: Configuring ASA5510 To Allow VLANs To Internet
Jan 29, 2012Here is what I have. Windows Domain Controller running DHCP with configured scopes.I have one ASA5510 And 4 HP Procurve switches with VLANS preconfigure from vender.
Here are my DHCP scopes/VLANS:
VLAN1 -Default 10.2.x.x/17
VLAN201 -DHCP 10.2.201.x/24
VLAN202 - WLAN EMP 10.2.202.x/24
VLAN203 - WLAN Guest 10.2.203.x/24
VLAN 252 - MGMT 10.2.254.x/24
Here is how I configured the DHCP Scopes:
Changes needed to make to the DHCP Server (AUSPDC) in order to get things working with the new switches.
1) Configure 3 new DHCP scopes on your DHCP server.
a) scope for 10.2.201.x/24 to serve LAN employees and give them a gateway address of 10.2.201.254.
b) a scope for 10.2.202.x/24 to serve WLAN employees and give them a gateway address of 10.2.202.254.
c) a scope for 10.2.203.x/24 to serve WLAN Guests and give them a gateway address of 10.2.203.254.
I just upgraded and decided to go with the VLAN configuration. None of my VLANS can get out to the internet or each other due to I think My ignorance in configuring the firewall.The PC's are getting proper IP address but they cannot get out or to the other VLANs. I tried to duplicate what is working for VLAN1 but it is not working.
Here is my config.
Result of the command: "show running-config"
: Saved
:
ASA Version 8.2(3)
!
hostname CiscoASA
domain-name hand.local
enable password 1FVULuGal5s1/ADt encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code].....
Cisco Switching/Routing :: Catalyst 3560 Can't Access Radius-server In Vrf
Aug 23, 2012My configuration:
radius-server host 10.138.44.57 auth-port 1645 acct-port 1646 key 7 ******
!
aaa new-model
!
aaa authentication dot1x default group radius local
[code]....
