Cisco Switching/Routing :: AIR-SAP2602I-E-K9 Unable To Access Internet
Feb 25, 2013
I have installed the six new WAP with model Cisco AIR-SAP2602I-E-K9, and we have two SSID for the new WAPs. When the users are connected to this WAP they can able to access the intranet but not able to access the internet. What could be the problem? I have checked and verify that they can able ping to the IP address of google from the CMD but when try from internet explorer they are fail (both with www.google.com & with IP address of google).
I am using a Cisco SG-300 28 port switch in layer 3 mode as my default gateway for all my devices. I have two vlans on the switch, vlan 1 and vlan 4. Both are pulling valid IP addresses in their scope from the DHCP server, and both have valid DNS settings. I set a static route to the Internet on the switch to our firewall (192.168.5.254). All devices connected to vlan 1 are able to access the Internet, however all devices connected to vlan 4 cannot get past the switch. A tracert from one of these devices shows it hits the switch as the gateway, but gets no further. [code]
I just find there is no "Crypto key generate" command line in my Catalyst4506-E with cat4500e-universal.SPA.03.01.01.SG.150-1.XO1.bin image. Is there any other command I can use to enable ssh access? this command is always able to use on other catalyst switch like 3750X.
I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
I am having trouble trying to configure my cisco 2509 cisco router for access server. I have two guides shown below: URL and URL
However I am running into some problems. I can go through the second guide up until it asks me to do this command
Step 5: Configure the transport input protocol on the async lines to Telnet. Access_Server(config-line)#transport input telnet
I cannot put in Transport Input, I only have the option of doing Transport Output let me show some lines from my console:
--------------------------- Access_Server(config)#line 0 14Access_Server(config-line)#no execAccess_Server(config-line)#transport input ?% Unrecognized commandAccess_Server(config-line)#transport ? output Define which protocols to use for outgoing connections preferred Specify the preferred protocol to use Access_Server(config-line)#transport ------------------------
Im not sure whats going on. I have two routers(cisco 2600 series) plus my 2509 cisco router I am going to use for a access server. I have a two switches 2950 series and I have the access server connected to all of them via a octal cable.
Here is the configuration from the access server:
-------------------------------------- Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-IS-L), Version 12.3(26), RELEASE SOFTWARE (fc2) Technical Support: [URL] Copyright (c) 1986-2008 by cisco Systems, Inc. Compiled Mon 17-Mar-08 14:39 by dchih cisco 2509 (68030) processor (revision M) with 14336K/2048K bytes of memory. Processor board ID 22840809, with hardware revision 00000000 Bridging software.
I have one issue on Vlan in Cisco 3750X switches , I have 2 Offices , I am sitting at corp OFfice and i have one 3750 ( 10.10.1.36)Switch at my location , in my remote office i have one more switch 3750 ( 10.10.33.1) and i am able to access the both vlan IPS with out any issue , now i have some network components in Vlan33 ( 10.10.33.1) at my remote office . i am able to ping 10.10.33.1 IP from my corp office , but i am not able to ping any network devices in 10.10.33.5 example : 10.10.33.5 is my Cyberoam IP at remote location and i am not able to ping , i have taken a trace route and not able to find the issue as i am not much femilar , ping 10.10.33.5 at remote location devicec
I am giving the Configuration for both locaitons below :
10.10.1.36 - Corp Office 3750 Switch: sh run L3-#sh running-config Building configuration...
I have setup a home lab for my CCNASecurity studies and have purchased a 2511 to serve as an access server. The 2511 was advertised as fully operational but when I powered it up this is the first error message I get.....
ERR: Invalid chip id 0x80B5 (reversed = 0x1AD ) detected in System flash
From my research it appears this may have something to do with an old ROM and newer flash, here is the ROM info....
System Bootstrap, Version 4.14(9.1), SOFTWARE Copyright (c) 1986-1994 by cisco Systems 2500 processor with 16384 Kbytes of main memoryHere is the info on the IOS..
[Code].....
Could this be a simple as a ROM upgrade which I have found on eBay for $10.00? Or do I have a larger problem?The boot continues appearing normal until it gets to ....
%SNMP-5-COLDSTART: SNMP agent on host Terminal is undergoing a cold start and then completely hangs.
Router ISP >>> Switch 2940 >>> Router 2620 >>> Host (Tacking dhcp from my 2620)
I got servers and other switches 2950 working perfect from the 2940....but the 2620 or even a Switch 3550 (in router L3 port), has the same issue...do not share connection with Host's behind them, I got IP on the host, pinging the Fa0/1 (dhcp), pinging the Fa0/0, but cannot ping the GATEWAY and not surf the internet.
I not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
I have router connected to 2 3550 switches directly. 3550A and B switches are running HSRP. OSPF is running between Router and 2 switches.
From Switch B i can ping the Router Wan interface but not the internet sites. from Switch A i can ping any sites?
Switch B 3550SMIB# sh ip routeCodes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1
We have recently leased an internet connection in our office which comes from the service provider as radio link and BW is 2M. I have clients more than 60 that will share the connection and access internet. I have configured a Cisco 2600 router as below:
Building configuration... Current configuration : 988 bytes ! version 12.2 no service single-slot-reload-enable no service timestamps debug uptime no service timestamps log uptime
[code].....
So far I have read regard NAT it degrades performance as it need to translate every data packet comes from the source and goes to internet. So a question comes in my mind is there any other way how I can share this connection among users with private ip address? Or NAT is the only method to share internet connection among users with private ip addresses?
I have a Cisco 3620 router and I am trying to get internet access. My isp is comcast. All modem lights seem to be operational. But I do not have internet access. I can ping anything other then the router and I am on a home network.
I have a Cisoc 2610 connected to my network, 1 Ethernet port and a WIC-2T card. I have ther serial connection to the main router and the ethernet going to the switch. I can ping all device throught the network...but the 2610 can't ping any outside address (no internet connection). I have the internet connection going through my 3745 (which the 2610 is connected to via serial cable). I put a default route into the 2610 but still no luck.
Here are the running configs:
2610: version 12.3 service timestamps debug uptime service timestamps log uptime
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
I'm currently undergoing CCNa academy so I got a "job" from my boss to configure Cisco 871 router. Unfortunately we just finished first semester at academy so there are some things that I'm still having hard time to understand. I managed to configure router so it connect to internet or to be exact it has internet access through another adsl modem that is in bridge mode. url...The problem is that users are not able to use internet when connected to this router. I'm able to access router through telnet ( ip 192.168.13.10) but that's it.192.168.13.0 255.255.255.128 is network that we use at work. 192.168.13.5 is IP address that is assigned to zyxel adsl modem ( If I'm correct, we could have used any address here since we are connecting this directly to router ? ) Zyxel adsl modem is connected to FA4 port on Cisco router. LAN cable is connected to FA0 port and from there it goes to switch ( it's some asus switch with 50 ports). [code]
If I ping google dns from router e.g. ping 8.8.8.8 it works. If I ping url... it doesn't work. Also I'm able to access router via 192.168.13.10 but if I use router as default gateway then I'm not able to access the internet.
i want to control access to internet on VLAN1 and VLAN2 (access on VLAN3), while providing access to VLAN4.My problem is in connecting to internet, i can't find a way to "route back traffic to VLANs 1 and 2 since HG8245 don't seem to provide proper static routing ON LAN interface. Maybe without resorting to changing the HG8245 router ?
We have a Cisco 3750 stack connecting to the MPLS router, able to ping 8.8.8.8 - [URL], the internal users on their own Vlan can ping the default gateway the 3750 switch but no further, trace route from the PC/Servers stops at the 3750 stack.We have the switch configured to ip route 0.0.0.0 0.0.0.0 to the public interface in the MPLS router, from the switch I'm able to ping the internet.
I am trying to setup VLAN's in the company I work for and I am almost there but missing the part when the internet works.I have an SG300 as a L3 Router IP 192.168.0.93.I have created VLAN20 and VLAN40 Assigned VLAN20 192.168.2.1 and VLAN40 192.168.4.1
The static routes have been created and a default router going to the Sonicwall firewall at 192.168.0.1.Port 24 is configured as Untagged VLAN1, Untagged VLAN20 and VLAN40 in trunk mode and going to the Sonicwall NSA 2400. [code]
Working to move all 192.168.0.x network off of VLAN1 and move it a management switch.I have DHCP helper on pointing to the DHCP server.Both VLAN's once the DHCP server is configured to Gateway 192.168.0.93 can get an IP from the correct subnet either 192.168.2.x or 192.168.4.x
All PC's are getting a GW IP of 192.168.2.1 pr 192.168.4.1.All test PC's on both VLAN's can ping each other and any server with the correct GW.When I try to ping google.com or open a web page and try google.com it times out.
Need to Have both ISP to access internet/servers configure a Cisco 2911 router, It has two ISP one as primary 216.140.140.0, and secondary for backup as 216.150.150.0. I need to be able to access both the ISP's using the same interface Gi0/1. Since we have servers that have to have specific IP both when accessed and when accessing the internet so I used static Nat for the servers and Dynamic for all others. I did the following configuration but it does not work as i want it, if i unplug the Primary ISP from the unmanaged switch the secondary cant access the Internet or network.The secondary only works when the primary and secondary are both connected and have an equal cost Administrative distance, hence it is not available when the primary is down . Even though I can use a sub-interface instead of a secondary Ip address (which worked when I used it) I need to use the same interface using a unmanaged switch to which the outside interface of the router is connected and the two ISP's. Below is my configuration.
interface GigabitEthernet0/0 ip address 10.0.0.254 255.255.255.0 ip nat inside
I have a 2960-S running the lastest software for testing on my bench:
[code] Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 24 WS-C2960-24-S 15.0(1)SE2 C2960-LANLITEK9-M [/code]
I have set up VLAN 2 on 192.168.2.0/24 with the switch as the DHCP server. The switch is connected to an RV082 router which is at 192.168.1.65/27. Once I figure out what I doing I'll eventually shift that to 192.168.1.0/24 or something similar. So I have my switch acting as the DHCP server for VLAN 2 but I can't figure out how to get it to access the internet.
I found this example to set up the DHCP server: [code] ################################### this works to get vlan 2 to serve ips conf t
[Code].....
The RV082 doesn't support trunks AFIK and I'm pretty much a newb at this stuff. TIA. I guess I should get a real router and I most likely will but I'd like to get this working if possible before taking the next plunge.
I want to set up my LAN to have internet access via my 2801 router.The 2801 router is connected to my home ADSL router.Now do I just configure a 0.0.0.0 'gateway of last resort' on the 2801 router pointing to the interface leading to the ADSL router ?Therefore, all traffic from my PCs that is internet bound will head out to the ADSL router and onto the internet.
At the core of my network I have two Nexus 5548's with the routing/L3 daughter installed. They have a default route that points to my ASA 5520 for Internet access. I have configured a VLAN that I do not want to have access to the Internet. What is the best way of preventing this access? ACL on the Nexus or Firewall rules on the ASA?
the cisco 2921 Router has a default ip hhtp access class command found in it. Just i changed the default IP to the new ip i will use.The Router is accessable from the LAN only but not from the internet configured the Public ip . I think this is due to the standard access list 23 . how will i access the Router from the Internet using the Public IP.
They have a locked Cisco Router which is from the ISP and its confed on a fa 0/0 interface to share Internet access on the network. The ip on that interface is 195.198.11.217 255.255.255.252 and i tried it with a PC (set my personal ip to .218 and entered their dns info (195.67.199.27) and it is working. The question is now. My friend found a 3550 laying around and since the ISP wont let them conf their router he wants to use the 3550 to create 2 vlans with internet access and without access to eachother. Vlan 10 for the desktops and Vlan 20 for the wireless (Moving on to some netgear wireless switches) How would you configure the 3550 for this to work?
i am trying to set up a cisco 2950 with a vlan to seperate all of the pos machines on the network (4 of them) from all other machnes in the building (3 hard wired and wi-fi). i was going to use vlan 1 as a trunk to allow internet access to go from fa0/1 to both vlans (vlan 10 and vlan 20). i have read things about the acl having an explicit deny at the end, so i'm thinking that is my problem. i am testing it at my house before deploying it to the network. i have 1 laptop setup with an ip of 192.168.0.50, and the other is .60. my router is 192.168.0.1. i have the ethernet from the router plugged into fa0/1, the 1st laptop on fa0/2 and the other at fa0/3. before i set the vlans up, i checked the communication by just plugging them in and trying to ping, they could both ping each other, the router and 8.8.8.8. when i finished setting up the test vlans, they could not ping each other(what i wanted) and laptop 1 can ping the router, and 8.8.8.8. laptop 2 cannot ping anything. the only thing i did was create vlan 10 and 20, set port fa0/2 to vlan 10 and no sh, fa03 to vlan 20 and no sh, fa0/1 to vlan 1 and no sh. then i did switchport mode trunk on fa0/1, and switchport native vlan 1. this seems to be how i was supposed to do it, but it's been a while since i have worked with switches. i'm sure it's simple, but after searching the internet and poring over my cisco books for 5 hours, it is turning out not to be the case. here are some details:
