Cisco Wireless :: Show Attached Clients On WAP2000?
Jul 15, 2010Is there no way to see which clients are connected to a WAP2000 Access Point? I'm not finding the option and a little
View 2 Replies
ADVERTISEMENT
Linksys Wireless Router :: Why Doesn't E4200 Wireless Router Show All Attached Devices
May 1, 2013I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results. Other than a factory reset, get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago?
View 2 Replies View RelatedCisco Wireless :: WLC 5508 Clients Show IP Address 0.0.0.0
May 16, 2012We got a question about our WLC 5508 single controller deployment with 14 access points without a VLAN configuration.
When our clients connect to the wifi, we cannot see any ip address of them in the client details page. It shows everytime the ip address 0.0.0.0. The clients are configured with a static ip.
Cisco Wireless :: 7.0.220 / Apple Clients Authenticated But Show No Username In WLC
Aug 1, 2012Running 7.0.220. There are several 'unknown' users every day reported in WCS. Investigating the connections on the WLC I find the clients are in a run state and passing traffic but there is no username listed on the client detail. (hence the unknown on WCS)
(mcm-189jsoc-wlc1) >show client detail 60:c5:47:07:b6:5a
Client MAC Address............................... 60:c5:47:07:b6:5a
Client Username ................................. N/A
AP MAC Address................................... 00:1e:13:42:16:a0
AP Name.......................................... mcm-208dorm-wap1
[code].....
Clients in this state are usually Apple products. From initial investigation it looks like the do authenticate with the ACS. r debugs to run, or fixes on the WLC? Perhaps there's a bug on this behavior?
Cisco Wireless :: WAP2000 As Repeater For WRT120n?
Mar 4, 2013I have a linksys WRT120N connected to the internet, and I want to set up my WAP2000 as a repeater. I followed all instructions, same SSID, Security, Channel, etc (y left the IP by default, though) but devices connected to the WAP2000 don´t get an IP and can´t connect to the internet. I wanted to kno if the WRT120n´s signal can be repeated, and if so if I need to change any configuration parameter.
View 2 Replies View RelatedCisco Wireless :: Can't Update Firmware On WAP2000
Dec 20, 2010I have a working WAP2000 that won't accept the 2.0.3.4 upgrade file. After selecting the file and pressing the UPDATE button, I receive the following error:
This webpage is not available.The webpage at URL might be temporarily down or it may have moved permanently to a new web address.
Cisco Wireless :: Use WAP2000 As Repeater Of AP541n?
Mar 22, 2011we want to use a WAP 2000 Box as repeater of an AP541n. Do naybody know this is possible or not?
Which Cisco AP boxes are compatible to act as repeater on a AP541n?
Cisco Wireless :: Can't Access WAP2000 Web Console
Jan 3, 2011We forgot the IP address of this WAP, and resetting the router doesn't take it to the default IP, no matter how I try to reset it. The SSID (and WEP key) stays the same too, which makes me wonder if the reset button is even working. We can still connect computers wirelessly through it and have them access the internet. Our issue is we need to change the SSID. Right now it just connects people invisibly - it gives them IPs from the subnet it's attached to, and yet the various DHCP servers I've connected to never show it as having its own DHCP address.
View 1 Replies View RelatedCisco Wireless :: WAP2000 Connection To Remote Office?
Mar 14, 2011We have a WAP2000 that supports a few wireless users in a shop environment. Users authenticate using RADIUS. Users connect without issue and can browse the Internet.
The main local network uses a Cisco 800 router to connect to the Internet via DSL and there is an IPsec VPN tunnel to our main office.
When a user is connected to the network via a wired connection, all systems work as expected. If they are on wireless, they cannot connect to services at the main office. They must make a PPTP VPN connection for applications to function.
The WAP2000 has the latest firmware 2.0.4.0. It has a static IP on the local subnet.
Cisco Wireless :: WAP2000 Track How Many Computers Connect
Mar 14, 2013I am doing support for a library that has 2 WAP2000 devices that have no security. These are for the patrons to connect to the internet at the library. They want to track how many people are connecting to the internet. Can I log how many computers connect to these access points or get another WAP that will track how many computers connect to the internet?
View 1 Replies View RelatedCisco Wireless :: Illegal SSID Name With WAP2000 Firmware 2.0.4.0
Apr 18, 2011Cisco has recently released firmware 2.0.4.0 for the WAP2000 wireless access point. This firmware has two annoying bugs in new JavaScript code which validates SSID names on the "Basic Wireless Settings" page.
First of all, this firmware does not allow SSID names to contain spaces, even though a space is a legal character in a SSID name!
Secondly, this firmware only allow the first SSID name to be 31 characters longs, even though the maximum allowed SSID name length is 32 (and the input field even allows 32 characters to be entered in the first place!)
If either case you will get an "Illegal SSID Name!" alert message (the developer could apparently not be bothered to make the message more specific and tell the user WHY the SSID name is supposedly illegal), and you will not be able to add additional SSIDs, or configure these existing SSID's on new access points that have this firmware.
The workaround is to revert back to firmware 2.0.0.5. You can upgrade to 2.0.4.0 after adding the "illegal" SSID names, they will remain after upgrading.
The new firmware does have an interesting new feature: it can download its configuration from a TFTP server (either through DHCP or by specifying the server), but I have not been able to find the documentation on how to get this working.
Cisco Wireless :: WAP2000 Admin Console Not Accessible?
Feb 13, 2011I'm having an issue with our WAP2000 access point. I had to reset the access point and now I can't access the admin console. I've set a static IP address just as I did when I first set it up. Now when I browse to the 192.168.1.245 in my browser it just displays an Authentication error.
View 1 Replies View RelatedCisco Wireless :: Cannot Find Power Injector For Wap2000
Jan 12, 2011Not long ago i was bought Cisco wap2000 access point for small business, and now the problem is to find power injector for this device. I am already tried to use AIR-PWRINJ3, but access point did't turn on.
View 7 Replies View RelatedCisco Wireless :: WAP2000 Work Smoothly As Repeater?
Jan 23, 2013Our customer setup requires an outdoor WAP (the main WAP) and two wireless signal repeters (that will be WAP2000). The repeaters will be powered over the Ethernet only and will be connected to the same switch as the main WAP (unknown vendor). My question is:
Will a WAP2000 work smoothly as a repeater when it's powered over Ethernet only and connected to the same switch as the main WAP is?
I noticed that WAP2000 connected this way was sort of 'lost' in deciding to repeat a signal or work as an independent wireless access point. The problem was immediately removed once the repeater was disconnected from the switch and powered from an outlet. I am not sure whether it was wrong addressing setup or something else that was needed to check/uncheck.
Cisco Wireless :: WAP2000 Prone To Reset Automatically
Aug 31, 2011I have a few questions about the Cisco WAP2000 we setup for our customers that I have experienced as of late.
1. The AP is prone to reset automatically; what causes the access point to do this and how can this be prevented?
2. The AP has the SSID and the encryption reset back to factory defaults, however the IP address does not get reset. What would cause this?
3. Is it possible to use 2 of the Cisco WAP2000 as a repeater to increase signal strength of another Cisco WAP2000 that has interference from another stronger signal?
Cisco Wireless :: Wap2000 Closing Ports After 10 Minutes Of Up Time
Mar 17, 2011We have two WAP2000's in our offices which we roam between depending on which office we are in. Lets call them Access point A and Access point B.Both are firmware 2.0.4.0 and have seperate IP addresses. Both are set up with two SSID's and VLAN tagging. Both handle connections just fine and can route traffic. Both are PoE and the catalyst switch reports PoE util at 25% over all of its ports.After 10 minutes of uptime, Access point B will close all of its TCP ports - SNMP, Web admin etc but does still handle wireless connections and traffic correctly. Access point A does not close any ports.I have confirmed that when the problem happens, Access point B still handles traffic just fine by checking the MAC address the clients is associated with, as well as powering down Access point A and confirming traffic is flowing. Access point B will also respond to ICMP ping after it has closed all of its management ports. I have confirmed there is no other device on the network attempting to use the same IP address as Access point B.
I have also confirmed that I am attempting to access the management ports from the management Vlan (1) - else I would not be able to reach Access Point A's management ports either. I have turned wireless management access on for Access point B and the ports close after 10 minutes of uptime from the wireless side too, so highly unlikely this is a vlan issue.I have confirmed all of the settings (bar the IP address config) exactly match on both Access point A and Access point B. The firmware revisions are the same.
Cisco Wireless :: WAP2000 IPhone / IPod Touch Cannot Connect
Aug 22, 2010I have several WAP2000 (Firmware 2.0.0.5), and while they work fine for PC's, iPhones, iPod touches cannot connect to them.Well, they connect briefly, get an IP address from the router, and immediately drop the connection to re-connect again.I have tried changing channels, eliminating all but one of the AP's, and so forth. Any issues with this firmware? I see posts where people are saying their iPhones connect up fine. This happens on versions 3.x and 4.x of the iphone O.S. It's not limited to one iphone or ipod touch; we've tried several.
View 12 Replies View RelatedRouters / Switches :: Dlink DIR 615 Router - Wireless Clients Can't See Ethernet Clients
Feb 1, 2011I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies View RelatedCisco Wireless :: Recognize Attached Antenna To AP1242
Nov 11, 2012Im looking for possibilities to remote recognize attached antennas to AP1242. I have a lot of devices which not working properly. I think most of them have only one antennas installed , but I cant be sure if its fitted into primary connector. Do You have any idea how to check numbers of attached antennas and if only one if its fitted into primary connector?
I want to disable diversity when I'll find APs with only one antennas.
Linksys Wireless Router :: How Many RE1000 Extenders Can Be Attached On One
Apr 13, 2012How many RE1000 extenders can be attached to one router ?
View 9 Replies View RelatedCisco Switching/Routing :: 3750 - Show Interface Vlan (ID) Doesn't Show In / Out Traffic Rate
Mar 13, 2013I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedCisco :: Understand Show Sessions And Show Connection Commands?
Jan 29, 2012How to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies View RelatedCisco Wireless :: Power Rating Of 1552e Mesh AP Before Antennas Are Attached?
Mar 15, 2013What is the power rating of a 1552e mesh AP before the antennas are attached? I have the dual band 2.4 / 5 GHz antennas. I know their Db rating, but I have not been able to find what the AP is.
View 1 Replies View RelatedCisco Switching/Routing :: 2960 Don't Display Logging Trap Informational In Show Running / Show Startup
May 27, 2012Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedLinksys Wireless Router :: NAS Attached HD On WRT610N Keeps Dropping Connection?
Nov 14, 2011I'm running Windows 7 Home Premium (64 bit) connected to a Linksys WRT610N Router. I have attached a 320GB USB 5400 rpm hard drive to the router as NAS storage.The router is running 2.00.01 build 15 firmware. I get frequent drop-outs when transferring large files. Tonight I've been trying to transfer a 4.36GB file to the drive from my PC. I've tried several times. At exactly the same time, with about 377MB to transfer I get a message saying 'There is a problem accessing Z: make sure you are connected to the network and try again'.
View 1 Replies View RelatedTp-link 300mbps Wireless :: Pc Attached Via Lan Or Wifi To Wr841nd Can Ping Only
Nov 5, 2012Region : Italy
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : TL-WR841ND_V8_120802I
Setup the WR841ND in wds and easily connect to d-link.with the ping utility of the WR841ND I can reach the d-link or any of the PCs attached to the d-link and receive an answer.but any PC 'attached via LAN or WIFI to WR841ND can ping only WR841ND and not the d-link or any other PC attached to the d-link (clearly not even go on the Internet
Cisco :: BRI Card Does Not Show In (show Voice Port)
Jun 18, 2011I have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies View RelatedLinksys Wireless Router :: E3000 Streaming Media From Attached USB Storage
Jan 9, 2011I am very pleased with my purchase of the E3000 so far. However, one function seems to allude me. One of the main reasons for purchasing this router was because of its Media Server functionality. I wanted to be able to stream to my UPnP devices (ps3, xbox360, etc) without having to keep my power hog of a PC running. I have set up the HD using the Storage tab of the Advanced Router Settings, and created several Shares on the Media Server tab. The good news is that I am able to access the share on my PS3. The bad news is that I can't on my Xbox360s. As the Xbox360s has built in wireless N, I would really like to be able to stream to that system.
View 8 Replies View RelatedLinksys Wireless Router :: E4200 File Timestamp On USB Attached Device?
Apr 26, 2011I've verified that the router and the pc have the same time zone, daylight savings update specification and that they both showed the same time (00:56AM). But a file created on the attached USB device was timestamped 01:56AM (the date was correct).
View 9 Replies View RelatedLinksys Wireless Router :: E4200 Wipes Attached HDD On Power Loss
Dec 18, 2011I'm loosing about 40GB of data. If worst comes to worst i might go with another brand of router instead as i don't wanna waste a lot of money again as i currently feel i have with the E4200. Enough whining, here is my problem. The FTP and Media Server feature works nicely. I have a 2TB USB 2.0 HDD attached to the router's USB port. I use it for images and my music collection ripped there so i can play it all from my PS3 and TV. I also have many GB of video recordings and converted DVD discs for easier access. (And no, before anyone speaks of piracy, it IS legal, at least in my country, to back up your legit media) Now, everything worked fine, until one day after a few weeks, the router hanged for some reason so i decided to reboot it. To my disappointment it also wiped video and audio from my HDD which really got me pissed as i lost all track of what i had on the HDD. The Media Server was also having connection issues once in a while so i decided to update the firmware from 1.0.00 to 1.0.03. It immediately fixed the connection issues of the Media Server. Another noticeable change is that files transferred via FTP will show immediately via the Media Server without the need to update the database via the router as i needed to do in 1.0.00. Now today there was a power loss in the neighbourhood so the router went dead along with the HDD. To my big disappointment, everything was gone from the HDD when i started it up again. Images, music, video and even my application backups etc. It was just plain empty except for the root folders. I have done a few tests and figured that even if the HDD stays on, cutting the power to the router will wipe the connected HDD. What's up with that? Even a silly Windows PC wont nuke your files that much if an accessed HDD was disconnected while in use. Do i really need a UPS system for the router and safely disconnect the HDD from the router via the user interface every day? If so, the concept of having a router with these nice features is really useless and money theft in my opinion.
View 9 Replies View RelatedLinksys Wireless Router :: Accessing Files On Attached Hard Drive To EA4500
Sep 2, 2012I have mapped the attached hard drive to my EA4500 on my PC and can access folders and files on my LAN PC. However, when I come in through the Internet via an iOS device, I can see folders but when I try to enter the folder, all I get is a message that displays "|Folder|Enter Into Folder|Select|. There is no click-through capability other than "Return to Upper Folder", which takes me back to folders.
View 8 Replies View RelatedLinksys Wireless Router :: E4200 USB Port / Recommended Format Of The Attached HD Drive / 512 Or 4K?
Sep 8, 2011what is the recommended format of the attached HD drive, 512 or 4K ?
View 6 Replies View RelatedLinksys Access Point :: IPad Keeps Disconnecting From WAP2000?
Jan 20, 2011I have an iPad 1 with newest iOS version connecting to a WAP2000 device setup with WPA2 Personal, MAC Address Connection Control enabled and SSID Broadcasting disabled, VLAN enabled (WAP2000 is running on latest firmware). Everything works well, but I keep seeing my iPad disconnecting (WIFI icon disappearing in status bar) after about 30-40 minutes of using wireless. It then takes about a minute until it connects again.
View 3 Replies View Related