Cisco WAN :: Linksys WRT120N As Access Point - Very Slow
Jan 14, 2011
I am using a linksys WRT120N router as a Access point in my student dorm (according to the rules!). As long as i used it as a router, I never had problems with the speed. But now, the connection is very slow.For example, when I am wirelessly connected to the AP, and when I ping the main router of the building, I see packet drops and some packets have more than 4000ms rtt. (while normally it should be b/w 0 and 1 ms). So as I understand it, there is some problem between the AP and my computer in the wireless channel or something but I have no clue.I am using the latest firmware from the CISCO website.
View 1 Replies
ADVERTISEMENT
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Sep 21, 2011
I am currently using a Linksys E2500 router and cannot get a strong enough signal to an upstairs bedroom for my wife's iPad 2. I have a spare Linksys WRT120N that I would like to utilize to increase the signal upstairs. There is no way I can run a CAT 5 cable to that room. I believe both routers have WDS.
View 5 Replies
View Related
Jun 5, 2012
I have a WRT120N I would like to convert from a router to a Wireless Access point. Can this be done and how would I do this?
View 4 Replies
View Related
Jul 19, 2011
I bought my self a WRT120N as my wireless router for my house. and not a long ago i bought the WAP4410N, for my repeater (after i ask to some people).my house were concrete wall, it have about 15-20cm thick, and we try to avoid any wired LAN. The destinaton were unreachable with only WRT120N.it's look like this (what i want for the network on my home) : [code] i already tried to setting the WAP4410 as a wireless WDS repeater, and wireless client/repeater (with and without "Allow wireless stations to associate"). both were unable to connect (limited), although i get the signal. for the IP on the WAP4410N (192.168.0.50), i used static IP [IP, Subnet and Default Gateway were fill in] within the WRT120N range (192.168.0.2 ->192.168.0.51)
- how i configure my WAP4410N as a repeater?
- is there any settings that i must set on the WRT120N, before combining the WAP4410N?
View 1 Replies
View Related
Jan 23, 2011
I have a Wap610n access point, when I am connected on the device in N mode I got an average speed of 50 bytes per sec, in G mode no problem with an average speed of 2.250 meg per sec .I have tried with 2 different USB keys (Belkin f7d2101 and Hercules hwnum-300) but the result is the same.The access point is configured in 2.4 GHz, band 40 mhz only, and I have verified that no other radio emissions are on the same frequencies than the Wap610n in my neighborhood.
View 7 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
Feb 10, 2012
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies
View Related
May 1, 2013
I have a point to point 100mb line connecting SG500x switches at 2 locations, with these ports in a vlan together. I use layer 3 on the SG500x's to route between the two sites. I also have RIP protocol enabled to allow for automatic failover if the point to point fails (this works well).
I upgraded the ios to 1.30.59, and the connection now runs at a fraction of the speed. I have hard-coded the ports to run at 100mb full duplex, but I still only get around 12mb of throughput between the switches. I used to get about 90mb before. The provider also hard-coded the circuit to 100mb full duplex. The provider has checked the circuit remotely, and everything looks fine. I tested with a laptop at each side, and did get almost 70mb throughput. I would think this indicates some type of setting mismatch, but i cannot find anything.
I am using a backup vpn for now as some things look flaky as well (on vpn, I can use the web interface to access the SG500x on the opposite side, but on the point to point I cannot - I can ping the device though).
I have seen some references on here to shutting off STP on these 2 ports.
View 3 Replies
View Related
Oct 3, 2011
I can't access the web based setup via 192.168.1.1. I've had this problem since I swapped to Static Ip from PPPoE. I changed internet provider and now when it type 192.168.1.1 in the browser it says Internet explorer can't show the web page. I've tried Crome and FireFox but with the same result. I followed the instructions in [URL] but to no result.
View 1 Replies
View Related
Jul 6, 2012
My Wireless-N Home Router WRT120N with version 1.0.07 seems to have a problem blocking Sites through scheduling with Access Restriction "Allow" ...I notice that... when I enable access restriction, with policy and some range of computers connecting to my router , and set it to "allow" from "monday - friday" from "8am-6pm" .. with a purpose of blocking some social networking sites, example facebook, It works perfectly fine. But when the "scheduled" time comes ( before 8am and after 6pm ).. I cannot access the internet.. router is working, it detects my modem.. but no internet connection. It always happen before and after the "scheduled time" before the configured access restriction takes over. I have to disable the Access Restriction to continue our internet access.
View 4 Replies
View Related
Nov 9, 2011
I have the CISCO Linksys Wireless Router Model Number: WRT120N. My laptop is finding the router, and connecting to it fine. However, when I try to log onto the internet, it says no internet connection (same in the available net work section in the menu bar).Internet (Charter) they have checked the modem and there is no issue. I have also plugged the Ethernet cord directly from the modem into the computer, and unable to access the internet.
View 6 Replies
View Related
Dec 5, 2012
I reset my router (WRT120N) and used a laptop with cable connection to reconfigure the router. With the laptop I can acces the router admin wireless, but with my home pc I am not able to acces the router! I get "The username or password you've entered is incorrect. Please check and try again." Like I said, wireless acces with laptop is no problem.Is this a security issue that allows only acces with computer that you configured the router?
View 4 Replies
View Related
Jul 15, 2011
The old configuration was a Linksys/Cisco WRT120N plugged into a NETGEAR ProSafe VPN Firewall FV336GV2. I will list the settings below, but the short of it is that the WiFi router was in charge of getting the wireless clients but the Firewall was the one that assigned IP addresses and all that. This setup worked out just fine except that the WiFi router was in the basement and clients could only connect to it while still in the basement. They wanted to be able to connect to the network wirelessly while on the third floor, but couldn't even see the basement router from there. We shipped out an identical router configured beforehand exactly the same way, save for its MAC address and local IP address (those having premonitions, during troubleshooting I try setting different radio channels as well). The client plugged an Ethernet cable from the wall to port #2, and a desktop to port #3.
The desktop has internet access. Wirelessly, however, had issues The client only had a single laptop to test with, an XP SP3 machine. Unfortunately I couldn't pull specs from it as of this post, so I don't know if it connected by G or N. This laptop, which worked fine in the basement, wouldn't connect upstairs (it would sit trying to get an IP address forever) until I had him "forget" the basement network. At this point, he was able to connect to the upstairs router and access the internet. However, he could then no longer use the access point in the basement. I tried the same troubleshooting steps, like having him delete the wireless profiles from his network card and rebooting the router, but he couldn't even see the basement router while down there anymore.
Occasionally, it would show up for a moment, then disappear before he could connect to it. To make sure it was the basement router that was briefly appearing, I renamed the upstairs router to something else; this confirmed that indeed it was the basement router that was doing the "now you see me, now you don't" act. I then tried setting the basement router to Channel 1 while leaving the upstairs one at Channel 6. Still nothing, even though the laptop was about 25 feet away from the basement router and I had him wipe the wireless profile again. Rebooting the computer didn't solve the issue either. After this, I named the upstairs router back to the same as the downstairs one and had him go upstairs to test; he could connect to it right away.
I figure this is either a configuration issue on the laptop or routers (or firewall). Unfortunately, there weren't any other wireless clients to test with, and I'm not sure there will be when I continue troubleshooting on Monday. By the way, I looked for a "bridge mode" option on the WRT120N and couldn't find one; I'm told that the firmware doesn't support it. I don't feel comfortable putting on alternative firmware unless it's literally the only thing that will solve this. The configurations for the networking equipment are listed below.
NETGEAR ProSafe Firewall:
IP Address: 192.168.50.1
Subnet Mask: 255.255.255.0
DHCP Server: Enabled
Starting IP address: 192.168.50.50
[code]....
View 1 Replies
View Related
Jul 24, 2012
I decided to limit some Internet time for the kids going off this router (which has been working great since set up) but my Access Restrictions tab is missing. I have an identical router at my work place, same version/firmware, same settings, but the one at work does have the tab.
View 6 Replies
View Related
Jan 7, 2011
I have been using Mozilla Firefox for about 5 or 6 years now, and I have always been able to access any router setup through Firefox. Now though, I strangely can't. I try to log in from Firefox and I get stuck at the log in dialog box even if I use the correct password. If I cancel, the router assumes that I do not know the password and I get the standard Linksys access denied page. I then start using IE[current version], and I can log in absolutely fine. I can still use Firefox to browse the internet. I can ping the router. I can use Firefox to access the router setup from a different machine.
[code]....
View 9 Replies
View Related
Apr 18, 2013
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. After all that I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port.
View 4 Replies
View Related
Mar 4, 2013
i have router lynksys WRT120N and the latest 1.0.0.7 firmware. And the problem occured frequently. At about 13.00 i went out, wifi was working okay. At around 18.00 i returned home and i was trying to connect to the wifi with my android phone, and suprisingly it did not work. I tried on my laptop and on a android tablet. It did not work. The only thing that i could figure it out is to reset the router. I checked the settings, and there was no access policy e.g. time based access blocking.
View 5 Replies
View Related
Jul 15, 2011
WRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port. Also the support site has been down for over 13 hours for routine maintenance service.
View 2 Replies
View Related
Jan 27, 2012
I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.
View 1 Replies
View Related
Oct 29, 2011
All the documentation for this router shows the Access Restriction tab in the router configuration menu. It's the same as other linksys routers. The current version of the firmware doesn't have this functionality. Was it removed?
View 5 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Aug 11, 2010
I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.
View 5 Replies
View Related
Jan 6, 2012
Have a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".
View 2 Replies
View Related
