Linksys Access Point :: Wap610n Very Slow In N Mode?

Jan 23, 2011

I have a Wap610n access point, when I am connected on the device in N mode I got an average speed of 50 bytes per sec, in G mode no problem with an average speed of 2.250 meg per sec .I have tried with 2 different USB keys (Belkin f7d2101 and Hercules hwnum-300) but the result is the same.The access point is configured in 2.4 GHz, band 40 mhz only, and I have verified that no other radio emissions are on the same frequencies than the Wap610n in my neighborhood.

ADVERTISEMENT

Linksys Access Point :: Can't Connect To WAP610n

Jul 25, 2012

I want to configure and WAP610N to work as an Access Point (it was configured by previous administrator some time ago): free hotspot open, LAN secured by password. What makes my last 2 days horrible is that I can't even get access to Administration Panel. Used Cisco Online Support Articles, used User Manual, tried many ways to connect without luck.First of all I've connected LAN cable directly from PC to AP and Windows stuck at "Identyfying State", after some hours "arp -a" command shows me only IP's of my LAN, no MAC of the AP.Tried to reset settings to the factory default - when on push for 30 seconds reset button, power diode blinks, ap starts and settings are the same - still connects to the company's LAN.Wireless networks is default 'linksys' without password I can connect to it and get the internet, after pushing fast connection button it changes to secured "Linksys-<some letters and numbers>" to which I can't connect.I can't even get IP on wired and wireless connection - DHCP don't work? I don't know what IP to set manually. How can I get access to Administration Panel? How to reset this thing?

View 4 Replies View Related

Linksys Access Point :: WAP610N Has Index 1 Only On WEP?

May 29, 2011

I cannot find the way to select another index Key on WEP.  I have already upgraded the farmware to 10.02 still a same.

View 4 Replies View Related

Linksys Access Point :: WAP610N Is Blocking LAN

May 12, 2013

I use my WAP610N as access point (AP) in a network with a router.Firmware is up to date (1.0.0.4 build 7).After I connect my mobile phone the AP crashes after a few minutes. (The firmware of the mobile phone is also up to date.)Then it blocks the whole LAN until I disconnect the network cable from the AP. Then the rest of the network works just fine.Blocking means, that a computer connected to a lan port of the router can't ping anything nor has access to the internet anymore.I need to power off the WAP610N and after the restart it works again.
 
Also is there any way to debug or at least show some kind of log on the WAP610N? The web client seems to have no such features. Is there an additional URL with more commands? It seems that theres no telnet console either.

View 5 Replies View Related

Linksys Access Point :: IPhone4 Cannot Connect To WAP610N

Jan 7, 2012

iPhone does not recognize home network. MacBook does! The phone recognizes and connects to all otther networks except this one at home.The WAP610N is used as an extender attached to Alcatel Lucent 7130.

View 2 Replies View Related

Linksys Access Point :: WAP610N Updating Firmware

Mar 26, 2012

I have a problem updating firmware for an WAP610N access point. The thing is i tryed to update from 1.0.01 to 1.0.03 and the update freezed at 49%. The next day it was restarted but of course it didn't worked again. The question is can i reset it some how so i can retry the firmware update ?

View 2 Replies View Related

Linksys Access Point :: WAP610N - Unable To Get An IP Lease?

Mar 22, 2011

I've recently purchased 5 WAP610N access points to replace my older US Robotincs access points.I've configured one WAP610N (upgraded to the latest firmware i found on the site) with a  static IP, bropadcasted SSID & WPA2 personal security.I had no problem at all to connect PC's but when i tried to connect the Ipad & Iphone (with the latest 4.3 firmware) i was able to connect to the network but unable to get an IP lease.  
I had no problem before connecting to the US roboticx access points.When i change (lower) the security to WEP on the WAP610N then everything works fine but i want to use WPA2 in stead of the unsecure WEP protocol.

View 1 Replies View Related

Linksys Access Point :: WAP610n Can't Change Wmm Settings

May 4, 2010

I try to change the wmm settings to video, but it's always going back to background settings after saving.I already re-uploaded the firmware, but with no result...I noticed that is a newer firmware available for the WET610n where they solved this issue, but they haven't changed it for the WAP610n....

View 9 Replies View Related

Linksys Access Point :: WAP610N Is Compatible With Wrt54g2?

Jun 15, 2011

tell me the compatable access point of wrt54g2 router.

View 5 Replies View Related

Linksys Access Point :: Best Way To Expand Signal WAP610N

Aug 22, 2011

I have a duplex on the first floor have the adsl router from the telephone company can not be replaced,the switch from a cable that comes into a room on the second floor where it was connected to an access point Linksys Wireless-N Access Point with Dual-Band WAP610N the signal on the first floor, however, comes down and in some cases just no signal. 

View 3 Replies View Related

Linksys Access Point :: WAP610N Compatible With WRT160NL?

Aug 1, 2011

Before I purchase, can I use a WAP610N as a wireless repeater for my WRT160NL?

View 2 Replies View Related

Linksys Access Point :: WAP610N - Way To Connect On DHCP?

Dec 9, 2011

I've some strange things with my WAP610.I connect it to my lan, my DHCP server assign an IP, that's normal way..I lookup for this IP, and fill in the address field in my IE (firefox or safari I've tried all of them).... the AP ask me password and user... I fill in the password field... and get into config...

So I think it could be a bug with static IP... I'll try on the wireless security... select "manual"... change nothing (leave default value) click save... wait a while... connect on the DHCP ip, return to the wireless page... and lost a lot of time since nothing is saved.

View 7 Replies View Related

Linksys Access Point :: WAP610N - Gateway Is Not Working

Sep 20, 2011

We have a several WAP610N Access points in our company since a few months and immediately noticed that it has problems with the gateway when you set it to use a static IP. (the AP loses its gateway when you pull the power). Today I saw that there was a firmware update, and in the firmware release notes it stated that the problem with the missing gateway info on the status screen was solved.
 
This info is correct. After updating to 1.0.0.2 the gateway is shown in the status screen when you use a static IP, but the actual function of the gateway is still not working after restarting the AP! I already let our reseller create a support call with Linksys a few months ago, but in the end they told me this would probably not be fixed and that I had to use DHCP.

View 2 Replies View Related

Linksys Access Point :: WAP610N As Wireless Range Expander?

Jun 21, 2011

I have a WAP610N that I would like to use as a range expander on an existing wireless network.  I want to be able to seamlessly move around the house and yard using both my router and WAP without getting disonnected.  Can the WAP610N be configured to work this way?  Any special settings to be aware of?

View 6 Replies View Related

Linksys Access Point :: Unable To Use Wap610n - Network LED Blinking?

Mar 23, 2011

I have a wap610n access point, which failed during an upgrade. Now it just comes on with the power led and the network led blinking but there is no connection. i have tried the 30/30/30 resetting process but its still not working.

View 1 Replies View Related

Linksys Access Point :: WAP610N - Unable To Obtain IP Address

Dec 14, 2012

I bought a Linksys WAP610N today, i placed it so i could get a signal where i can't normally.
 
The thing is i configured it correctly, well at least i think, i can see it on my wireless network, with a good signal, but on my Android tablet (Google Nexus 7), it can't get past the "Obtaining IP address".
 
I called the technical support, the person there tried to assist me for about 1 hour, we tried different settings, we upgraded firmware from 1.0.01 to 1.0.04, but it didn't worked. Now he said someone will call me tomorrow during the afternoon.
 
My router isn't Linksys, it's a Netgear, i don't have wireless problem when i connect my tablets or any other wireless device on it, it's just that i bought this WAP610N to have the signal in my bedroom, where i don't get any signal normally.

View 7 Replies View Related

Linksys Access Point :: WAP610N Refuses To Accept Password?

Dec 12, 2012

I set up the WAP610N as a wireless access point, and it refuses to accept the passsword on several iphones (2 iphone4s and one iphone5) and a kindle fire.
 
The devices are picking up the network, but when the password is entered, the access point refuses the password. I've checked the password numerous times and the spelling is correct.
 
If the access point's settings are set to no security, there's an instant connection, which I expected, but the password is refused on either of the secure settings.
 
I bought the WAP610N for my son months ago, but he couldn't get it installed in his old apartment several states away because he doesn't have a CD drive in his computer. Now that he's moved into an apartment close to home, I was able to set it up using my computer. So I don't know if maybe it's a firmware issue  since it sat in the box for months, or something else.
 
The access point is hooked up through a TP-Link TL-R860 Cable/DSL Router., which is not wireless.

View 2 Replies View Related

Linksys Access Point :: WAP610N Wireless-N Repeating Signal

Sep 14, 2011

Is it possible to use  WAP610N Wireless-N Access Point repeating signal with another  WAP610N Wireless-N Access Point?what the range of signal when using a single WAP610N Wireless-N Access Point ?How many devices can connect to WAP610N in the same time?

View 1 Replies View Related

Linksys Access Point :: View Connected Devices On WAP610N?

Jan 17, 2012

Is there a way to view the connected devices on the WAP610N?

View 3 Replies View Related

Linksys Access Point :: WAP610N Loosing Wireless Connection

Jun 13, 2011

I  had the WAP610N for a few months with no issues.  As always, I have a custom SSID and password, using WPA2.  All of a sudden, none of my mobile units (at least 5) are unable to connect via the WAP610N.  However, I can connect to a Netgear N750 w/o any issues.  When I reboot the WAP610N, it resolves the issue for a few minutes, but then behaves the same as before.  I know its not my network because, I am able to connect via wired and wireless via the Netgear.  I verified via the web interface that none of the settings/configurations have changed - but still nothing. Latest firmware has been applied.  Note sure If I should perform a factory reset or re-apply the firmware.

View 2 Replies View Related

Linksys Access Point :: WAP610N No Devices Connected To Wireless

Jul 21, 2011

I have a big house so I have a e4200 on one end of the house upstairs and the WAP610n on the other end downstairs linked via CA6.  I am having no issues with Laptops etc..just with Apple devices.  I spent a lot of time with chat support (waste of time).  WAP was flashed with latest firmware via hard wire no devices connected to wireless, has same ssid and security settings as router running on 2.4 ghz wpa2 personal AES.  I am using 2.4 due to iphone4 does not support 5ghz and wap does not support dual band (another bummer). I am using AES instead of TKIP/AES mixed mode due to apple devices will not acquire dhcp with this setting and if they do they lose it right away.  I have tried everything imaginable with the settings even changed beacon to 75, 50 RTS to 2304 etc...the current setting are the only ones that seem to work the best however when i run speedtest.net LA server or SD server the performance is horrible.  On windows laptop i can achieve 27mbps down 2.5mbpsup, my apple devices use to achieve very close numbers to that on a simple configuration with two Dlink DGL-4300's one as router one as AP (G mode).  So two major issues i have noticed is WAP610N has issues passing DHCP to apple devices and has extremely poor performance.  So my question is will there be a firmware to correct this issue or a new hardware version that i can exchange this for if I RMA it or would it be best to call it a day and just get a E3200 and use it as a real simultaneous dual band AP???

View 9 Replies View Related

Linksys Access Point :: WAP610N - Goes In Stand By And Doesn't Connect

Nov 16, 2011

we have 2 Access point WAP610N. The after some time goes in stand by and we doesn't able to connect to it. We updated at last firmware (1.0.02 build 3, Feb 25, 2011 ) Timeout inactivity 3600 Renewal key 600 Protection WPA2-PERSONAL

View 1 Replies View Related

Linksys Access Point :: WAP610N Unable To Provide Dhcp

Oct 16, 2010

I set up my internet access by adsl modem as gateway, then RV042 as load balancer and dhcp server, security by MAC address restriction and static IP assignment. WAP 610N used as access point.works great for first few weeks, then somehow I can't access the network.I've been using linksys on my SOHO network, no problem before (RV042+WAP54g)

View 9 Replies View Related

Linksys Access Point :: WAP610N - Setup Not Finding Device

Jul 2, 2011

I've got a WAP610N access point and 4 WET610N to connect to it - however, no matter what I do when trying to install the WAP610N the setup tells me it cannot find the device.I've got the WAP610N connected to a homegateway (SAGEM) and my computer connected wired to the HGW. The HGW is setup as a DHCP server, everything beside the WAP610N works. It gets an IP address, and I can login to the web interface of the access point - but is still unable to use the setup and unable to connect any of the WET610N.

View 2 Replies View Related

Linksys Access Point :: WAP610N AP For Extending WRT320N Router

Jul 30, 2012

I'm trying to configure WAP610N access point to enlarge my existing wifi network (WRT320N router). I configured WAP610N with the same SSID. WAP610N is on channel 6 and WRT320N is on channel 1. Both have WPA2-Personal encryption, the same key.The problem is that no matther what, my laptop connects only to the router (WRT320N):I tried to put the laptop near the WAP610N, disconnect / connect to the network, walk with the laptop between the router and ap... it only connects to the router.

View 3 Replies View Related

Linksys Access Point :: Download WAP610N Firmware Version 01.0.00 Build 832?

Dec 21, 2011

Is there anywhere I can download  WAP610N Firmware Version 01.0.00 build 832?  I have two units with this firmware version that work OK.  I recently purchased another unit that has WAP610N Firmware Versions 1.0.01 and and can only access an IP address if I do not use any security. I also spent a lot of time on the phone with Linksys support to no avail.

View 6 Replies View Related

Linksys Access Point :: WAP610N - Random Disconnections With Mobile Devices

May 17, 2012

I have installed 4 of these units in a commercial premises offering free wifi. Since the day they were installed (5Months ago) we had connectivity issues with mobile devices. This was somewhat resolved in the latest FW 1.0.04 but we are still having random disconnections on the units every 2 - 4 days and have to reboot the units. Lately the units have become unresponsive and reset themselves back to factory settings.
 
What we have done so far:
 
Changed router models - No change
Changed from Static IPs & DHCP - No change
Turned on isolation - No change
Performed a wifi analysis to pick the best channel for each unit - Slight signal gain but still disconnects
Changed to 20Mhz only (And all other variations) - No change
 
I think I am left with no option but to return these for some other brand. I'm really regretting buying these units at the minute...

View 8 Replies View Related

Linksys Access Point :: WAP610N - WLAN Printer Network / DHCP Server?

Oct 27, 2011

I use the WAP610N as an Accesspoint for only an small Mobilephone to WLAN Printer Network.My big Problem is that i have therefore no DHCP Server in this special small WLAN Network.And now i need an own DHCP Server from the Accesspoint side because otherwise i must use static IP Adresses in all Mobilephones to connect with the WLAN Network .In the WAP610 unfortunately there is only the choose between static IP Adress and IP Adress FROM an existing DHCP server .

View 2 Replies View Related

Linksys Access Point :: Wap610N After Establishing Connection / IPhone See Network Domain But Doesn't Connect

Jul 11, 2012

I reset the wap610N,after establishing connection, my iphone see my network domain but does not connect. I heard of dual band setting,how do i go about that. What must i do to establish connection with the iphone.

View 4 Replies View Related

Cisco WAN :: Linksys WRT120N As Access Point - Very Slow

Jan 14, 2011

I am using a linksys WRT120N router as a Access point in my student dorm (according to the rules!). As long as i used it as a router, I never had problems with the speed. But now, the connection is very slow.For example, when I am wirelessly connected to the AP, and when I ping the main router of the building, I see packet drops and some packets have more than 4000ms rtt. (while normally it should be b/w 0 and 1 ms). So as I understand it, there is some problem between the AP and my computer in the wireless channel or something but I have no clue.I am using the latest firmware from the CISCO website.

View 1 Replies View Related

Linksys Wireless Router :: E4200 As Access Point / Bridge Mode?

Sep 6, 2011

I have spent most of the weekend trying to get this router to act as a proper Access Point.
 
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
 
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
 
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
 
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
  
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
 
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.

View 4 Replies View Related

Linksys Access Point :: Use Two WAP54G APs In Bridge Mode To File Share?

Aug 16, 2011

Can I use two WAP54G APs in bridge mode to file share. I'm not interested in sharing internet. Just need to share files between two desktops. Would this work if I set a static IP on the two computers or do I need to have a router in the network as well?

View 1 Replies View Related

Linksys Access Point :: WAP54G V3.1 Bricked After Enabling Client Mode

Sep 15, 2009

I was using WAP54G in our company in AP client mode to support "wired" connection to far workstation being part of Windows Domain (it needed network connection before logging to windows). It was working fine for a year, secured with WPA. this AP client was wirelessly connected to another WAP54G unit running regular AP mode.
 
Today was changing configuration on "AP client" , wanted to cvheck if WPA2 is supported while in AP client mode. well it wasn't, so ireverted the config back to what it was. after power cycle device stays in "bricked mode".
 
it doesn't boot up, LAN port inactive (like a cable unplugged), no WiFi, only 2 LEDs are lit permamently red POWER and yellow LINK. green ACT is dead. resetting is no luck, tried resetting it multiple times holding it with device powered on or off, tried 30/30/30 method, no luck.
 
finally took it apart (was out of warranty anyways) and shorted pin 16 (A18) on flash chip (Spansion) while powering up and it worked to the point when LAN interface becomes operational with 192.168.1.245 IP and i get ping response.
 
I thought that's it, would just re-load firware (original latest 3.04.03)  and done. i was wrong. device takes fw via tftp, but immediately after tha it stops responding, green ACT never comes back online, reset still do not work. after power cycle LAN port is dead (as well as device) again. what has happened to it?

View 9 Replies View Related

Linksys Wireless Router :: WRT54G In Access Point Mode Impossible

Jul 18, 2011

I have a network with 2 WRT54Gs in it. One in the besement connects to my cable modem and serves as a gateway and DHCP server as well as a wireless access point. That WRT54G is perfectly accessible. I have another in my room set up as a router and access point only, connected by its ethernet port to the gateway. This one proves a bit trickier. Thet network works flawlessly, and if I couldn't see it sitting right there I would doubt it even existed. I can't ping it (I forgot the IP but tried all the ones that seemed logical), it doesn't show up in my network map, etc. From what I gather that's how a switch is supposed to work. But since this is also a managed router, I would think there should still be some way to connect to it to administer it. How can I log in to this router to change settings if I need to?

I'm not sure if maybe 192.168.2.0 is the other router or if that's some kind of special address (My network is on the 192.168.2.* subnet, don't even ask why...). I've seen it in other posts about routing tables but they all had it routing to 0.0.0.0 instead of the router's own IP. I tried pinging 192.168.2.255 and got no responses at all, not from any computers or from either of the routers, so that was not useful. Tracert from my computer to the gateway doesn't show the router (my computer connects to the gateway through the router).

View 4 Replies View Related

Linksys Wireless Router :: E1200 - IP Ranges As Access Point / Bridge Mode

Mar 18, 2013

I have a Cisco 880 (supplied by my company and as such I have little access to the control panel). I have a Linksys (Cisco) E1200 to use as an access point. Cisco setup (love it!) but the simple setup gives the E1200 an ip range starting at 192.168.1.1 while the Cisco 880 range is 192.168.185.113. I need to have all connections in the same ip rage (192.168.185.xxx) for remote monitoring. What is the best way to accomplish this? Bridge mode (I don't need Guest Mode which I read is not possible in bridge mode)? Disable DHCP on the E1200?

View 1 Replies View Related

Linksys Access Point :: X3000 And WAP200 - Can't Adjust Wireless Repeater Mode

Feb 7, 2013

Bought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?

View 4 Replies View Related

Linksys Access Point :: WAP54G - Client Mode Doesn't Work With WPA2?

Mar 12, 2012

I have a WAP54G v3.1 running firmware version 3.05.01 and a WRT54G v3 running Tomato v1.28. The  WAP54G is configured client mode and works perfectly. However, I was not able to get the two to communicate with WPA2 security - maybe, I just didn't try hard enough?  Both devices are capable of doing WPA2 with AES but client mode doesn't seem to work with WPA2?   I had to drop back to WPA-AES to make it work.   Why is this?

View 4 Replies View Related

Linksys Wireless Router :: Connect To EA6500 In Bridge Mode Acting As Access Point?

Mar 4, 2013

How do I connect to the EA6500 once it's in Bridge mode acting as a wireless access point? Checked the posts and some seem to be able to do this but, we cannot.

View 6 Replies View Related

Linksys Access Point :: To Work The Wireless Repeater Mode Work With WPA2-AES

Sep 6, 2011

Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?

View 4 Replies View Related

Belkin Routers :: N600 - Unable To Access Dashboard In Access Point Mode?

Mar 6, 2013

Setup N600 DB as an access point using the most recent firmware,3.03.12? Once I do I'm not able to access the dashboard even through I enabled the remote management option.

View 2 Replies View Related

Belkin Routers :: F9K1102 V1 Guest Access While In Access Point Mode

Jan 17, 2013

I have an n600 ( F9K1102 v1 , firmware 1.00.09 ). My ISP provides my main router for my network, but I want to use the N600 as an access point, I have activated the "Use as Access Point" feature.Is it possible to still utilize the Guest Access feature in this case?

View 1 Replies View Related

Ea4500 As A Wireless Access Point Only Mode

Aug 18, 2012

Ea4500 as a wireless access point only mode

View 1 Replies View Related

Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?

Nov 1, 2012

How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.

View 1 Replies View Related

ADVERTISEMENT